Question about 1984 Toyota 4Runner

2 Answers

Headlight installation 1986 Toyota pickup. How do you take off the headlight housing?

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 42 Answers

You must first, remove the grill on the front of the car. Above the bumper. It has very fragile clips, they have two tabs each, you must line them up with the small slots. Then pull the grill off. Then use a Philip screw driver to unscrew the head light hold down covers then pull the light out and unplug the three wire plug.

Posted on May 06, 2009

  • Toyota Guy
    Toyota Guy May 06, 2009

    First remove the grill. To do this you must line up the tabs on the clips on the grill with the small slots on the grill. Then pull it off. then use a phillips screw driver to unscrew the head light housing. pull the light out and unplug the three wire connector. Good luck

  • Toyota Guy
    Toyota Guy May 06, 2009

    Sorry that was repetitive.

×

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

You will have to take the grill off and after you to that you will see 3 screws around the headlights, there will be a spring holding the headlight housing on as well

Posted on May 15, 2009

1 Suggested Answer

Toyota Guy
  • 42 Answers

SOURCE: Headlight installation 1986 Toyota pickup. How do

Take a long flat head screw driver and a good flash light and move the tabs on the clips in to the slots. when you get the grill off then use a philpps screw driver to remove headlight holder. be care full those clips break easy and some people put wood screws in to replace the broken clips.

Posted on May 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do to change headlights on my 1990 toyota pickup


On my 1986, you have to take the grille off which is held in place by plastic push and twist fasteners. It's a pain. Then you have access to remove the headlight securing frame that fits around the perimeter edge of the headlight. Once that is removed the headlight pull out, pull the plug off the back connectors, and reverse the process.

Jun 22, 2014 | 1990 Toyota Pickup

2 Answers

How do I get to the front headlight to change it


Re: Replace headlight bulb

  1. INSTALLATION GUIDE:
  2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
  3. Parts Identification:
  4. Projector Headlight
  5. Halo & L.E.D.
  6. Bottom of the Headlight:
  7. Ballast Bracket, Halo Wires(red/black)
  8. Turn Signal Adaptor
  9. TOOLS REQUIRE
  10. 10mm - 8mm socket
  11. Philip Screwdriver
  12. Crimper/Pliers
  13. For more information about how to install your vehicle, come visit our youtube page on
  14. http://www.youtube.com/spyderauto
  15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
  16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
  17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
  18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
  19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
  20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
  21. STEP:
  22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
  23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
  24. Factory Xenon Headlight
  25. Spyder Projector Headlight using Factory Xenon Lights
  26. STEP:
BMW e46 HID Headlight Replace
get-front-headlight-change-afy5cnsznmokzumyhdcbeseq-5-0.jpg

get-front-headlight-change-afy5cnsznmokzumyhdcbeseq-5-2.jpg

Nov 22, 2012 | Cars & Trucks

1 Answer

Replacing headlight on 1989 Toyota


if the turn signal cover is loose, and you are not really sure and dont want to break yours, visit your local junk yard and try the exact same thing there. But you could always try a rag and a flat head screwdriver, use the rag to cover the screwdriver and gently pry the turn signal lens out from the back of the housing. Usually the rubber grommets have just gotten old with age and weather. have you tried removing your headlight? although rare, somethimes the headlights need to come out first with certain models.

Oct 29, 2011 | 1989 Toyota Pickup SR5

1 Answer

1986 Supra. Head lights pop up but does not turn on.


the headlight pop-up circuit is different from the lights themselves. Check the headlight fuses in the engine compartment fuse box. If the fuses are good then check the headlight relay. It is in the same fuse box just behind the headlight fuses. (The headlight relay is the second relay from the right side of the fuse box. the relay at the far right is the electronic fuel injection main relay.)

Jan 30, 2011 | 1986 Toyota Supra

1 Answer

How to install headlights on a 1992 toyota 4x4 pickup


To remove old light, remove screws holding the trim around the headlight. Some models require removing the grille to access them. Headlight should pull out and you can detach the plug. Install in reverse order.

Sep 01, 2010 | 1992 Toyota Pickup

1 Answer

How to replace headlight of 1993 toyota pickup truck


Remove screws holding trim around headlight, some models require the grille to be removed. Headlight then pulls out and can be unplugged.

Aug 28, 2010 | 1993 Toyota Pickup

1 Answer

How to replace headlight on 1990 toyota pickup


My son fixed the headlight. There were some odd clips holding the headlight in.

Nov 25, 2009 | 1990 Toyota Pickup

1 Answer

Headlight installation 1986 Toyota pickup. How do you get the headlight housing off? There are little clips around it, but I can't remember how to undo them.


Take a long flat head screw driver and a good flash light and move the tabs on the clips in to the slots. when you get the grill off then use a philpps screw driver to remove headlight holder. be care full those clips break easy and some people put wood screws in to replace the broken clips.

Feb 26, 2009 | 1984 Toyota 4Runner

1 Answer

1986 toyota pick up headlights blink on and off


on1986 toyota both headlight share common ground. first chek bulbes and make sure they are o.k.
if bulb are fine check ground for headlight (black wire) if o.k you need a headlight switch.

Jan 27, 2009 | 1986 Toyota Pickup 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

890 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...