Question about 2004 Volvo XC90

1 Answer

The ingnition switch will only turn from 0 to 1

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 76 Answers

Most likel the ignition cylinder has failed and will need to be replaced. It has break away bolt that have to be drilled out. I suggest you take it to a reputable shop for the repairs since the steering wheel, contact reel, and steering wheel module have to be removed to get to it.

hope this helps.

Posted on Feb 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Toyota sequoia that shut off going down the road. When you try to start it the key doesn't spring back it stays in the starting position and you have to manually turn it back.


Go to the back of the ingnition switch take two screw off and the switch will come out take a screw driver and try to turn the switxh
by hand if the switch returns then you need to look further into
the steering colume if the switch does not return on its own
replace it.its white if you cannot get to the screws on the back of the ingnition switch take a chizzle and turn the break away bolts
until they come out and pull the whole assemble.

Jun 22, 2015 | Toyota Cars & Trucks

1 Answer

How do I remove the top steering column cover on a 2005 Buick Rendezvous?


you take the front off of the wheel and access the screw for the arm,through a hole in the center of the wheel

May 27, 2015 | 2005 Buick Rendezvous CX

2 Answers

What is the proper way to check voltage to ingnition switch (key)


isit a electronic speedometer douse the dashboard go dead???mick
only if so could be faulty egnisstion switch????MICK

Feb 19, 2013 | 1995 Chevrolet K1500

1 Answer

Key won't turn ingnition


your switch has jammed up force key to turn at same time turn back and forth on steering wheel even if it will turn the key side of the switch will have to be replaced a ford dealer will have to program the new key it takes about a 1 1/2 hours to do.

Jul 29, 2012 | 2001 Ford Taurus

1 Answer

Ingnition won't turn past the accessory position


There is a piece of forged metal that is called a rack that attaches to a rod that gies down to the bottom of the column to the Ignition switch these racks have been known to break and jamb up and I have also seen Ignition switches jamb also. Go to the base of the column and remove the switch and see if the key lock cylinder moves all the way now. Then trace your problem to either a jambed Ignition switch or a bad rack and rod.

Jul 26, 2010 | 1989 Chevrolet Camaro

1 Answer

Replace ingnition switch on a 1995 vw passat ?


You must also remove the wiper / turn signal switch cluster. Before you can do this... Most of the 1995 Passats were fitted with a splined cone fitted on the steering columb just under the steering wheel. However a special pullers is needed to remove this cone. With this cone and the trim around the switches removed its a simple enough to remove the ignition switch.
All the best
John

Aug 15, 2009 | 1995 Volkswagen Passat

1 Answer

I installed a new ignition switch in my 1988 mustang


there is a ingnition rod going from key switch to ingnition switch ,it is probly not in the slot any more or the ingnition cam is broken

Jun 28, 2009 | 1988 Ford Mustang

1 Answer

97 cavalier was running but just stopped.


Question:
Did you replace the ignition switch or the KEY AND CYLINDER?

These are the only 2 things that can make your engine turn off when you release the ignition switch after starting the engine.

I hope this helps you.
ramonalees.com

Jan 30, 2009 | 1997 Chevrolet Cavalier

1 Answer

Key in ingnition will not turn steering whelel


Push in the key, while turning at the same time. If it still does not turn freely. Try wiggling the wheel a little bit. Do not put too much force, the key may break inside the switch. If that does not work, make sure the car or truck is level . Preassure on the wheels places preassure on the sterring wheel also.Then try again.

Oct 18, 2008 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
2004 Volvo XC90 Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Mark Jones

Level 2 Expert

76 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...