Question about 2001 Chrysler Town & Country

1 Answer

I have a problem there is two cable that comes from the negative battery and it goes down to the engine starter can some one tell me were those two cable goes its a Chrysler town and country

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 41 Answers

One should go to the engine block/starter and another one should go to a body ground, usually right on the fender next to the battery

Posted on Feb 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the starter located on a 2008 pontiac g 6 4 cylinder


Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle. Remove the "S" terminal connector from the starter solenoid. Remove the engine harness lead (2) from the starter
Remove the positive battery cable nut (2) from the starter solenoid. Remove the positive battery cable (3) and engine harness terminal (4) from the starter solenoid.
Remove the starter motor bolts. Remove the starter motor.
Has four engines possible in your G6 ,starter removal is simalier for all except one the catalytic converter has to come off.

Mar 30, 2015 | 2008 Pontiac G6

1 Answer

Unable to figure out how to remove negative battery cable from starter


The negative of a vehicle goes to the chassis (ground) the positive goes through the solenoid to the starter. The smaller wire comes from the ignition. The starter has no ground wire since the case of the starter is bolted to the engine block to make it's negative connection. I always remove the starter and using emery cloth i clean the bolts and wherever the bolts touch. I also clean where the starter presses against the engine block. This is to ensure that the connection is tarnish and oil-free. Remove the ground cable from the battery before beginning to remove the starter.

Nov 07, 2013 | 2003 Pontiac Grand Am SE

1 Answer

1979 C20 starter cable replacement


corroded at the battery I guess..or the entire wire..these come in certain lengths but I guess you will need about 4 ft or longer it goes from the battery positive (red cable) all the way to the big top stud on the starter solenoid which is above the starter..black cable(negative) goes between the battery negative and the engine block either on the alternator top bracket or some metal spot toconnect to.. the starter has a secondary wire which will activate the starter with the key switch and it is usually a brown wire with an eye on the end with a smaller stud nut to connect to the solenoid..good luck

Jan 20, 2013 | Cars & Trucks

2 Answers

I have a Triumph Spitfire MK2 1965. How do I tell if it is a pos gnd or neg gnd


Easiest way is to follow the battery cables. if the Negitave (-) goes to the engine block , frame or body, that is a negitive gorund system. If the Positive (+) does, it is a Positive ground system.

Mar 23, 2011 | Triumph Tr 7 Cars & Trucks

1 Answer

Where is the starter located on my 2003 nissan sentra ser


Starter Motor -located to articulate with flywheel that has gear teeth between the engine and transmission accessible from down below. REMOVAL & INSTALLATION 240SX WITH AUTOMATIC TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Support the transmission with a jack and remove the 4 rear mounting bracket bolts.
  3. Lightly lower the transmission to make room and pull out the dipstick tube.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  5. Install or connect the following:
    • Starter and torque the bolts to 30-37 ft. lbs. (40-50 Nm)
    • Harness connector
    • Connector bracket to the front mount bracket
    • Dipstick tube
    • Transmission into position
    • 4 rear mounting bracket bolts
    • Negative battery cable
  6. Remove the transmission jack
WITH MANUAL TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  3. Install or connect the following:
    • Starter and torque the bolts to 30-37 ft. lbs. (40-50 Nm)
    • Harness connector
    • Connector bracket to the front mount bracket
    • Negative battery cable
1.6L and 2.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Wiring at the starter
    • Bolts attaching the starter to the engine
    • Starter
    To install:
  3. Install or connect the following:
    • Starter and torque the bolts to 70 inch lbs. (8 Nm)
    • Starter electrical connections
    • Negaative battery cable
Maxima
  1. Remove or disconnect the following:
    • Negative battery cable
    • Air duct
    • Harness protector from the harness
    • Starter wiring at the starter
    • Starter-to-engine bolts
    • Starter from the vehicle

      Image 89612G12l Not Found

    To install:
  2. Install or connect the following:
    • Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) and the short bolt to 22-30 ft. lbs. (30-41 Nm)
    • Starter wiring
    • Harness protector
    • Air duct
    • Negative battery cable
Altima
  1. Remove or disconnect the following:
    • Negative battery cable
    • Air inlet tube
    • Harness bracket
    • Wiring at the starter
    • Starter
    To install:
  2. Install or connect the following:
    • Starter and torque the bolts to 60 inch lbs. (7 Nm)
    • Starter electrical connectors
    • Harness bracket
    • Air inlet tube
    • Negative battery cable

Nov 03, 2010 | 2003 Nissan Sentra

1 Answer

How do you remove a 1999 Nissan Altima starter?


Nissan Car Altima & Sentra 1999-06 StarterRemoval & Installation
  1. Remove or disconnect the following:
    Negative battery cable Air duct Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle


  2. b53bb6c.jpg
    Fig. Starter location and mounting detail-3.0L Maxima with a manual transaxle


    b2eb267.jpg
    Fig. Starter location and mounting detail-3.5L Maxima

To install:
  1. Install or connect the following:
    Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) on Altima and Maxima and 41 ft. lbs. (55 Nm) on 350 Z. torque the short bolt to 22-30 ft. lbs. (30-41 Nm) Starter wiring Harness protector Air duct Negative battery cable
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1.6L & 2.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negaative battery cable

1.6L, 1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

2.4L & 2.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.4L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.5L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner cover and duct Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

3.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner case (upper) and air cleaner to electric throttle control actuator tube. Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle

    42c548c.jpg
    Fig. Starter location and mounting detail-3.5L engine

continue...

Apr 05, 2010 | 1999 Nissan Altima

2 Answers

Battery terminal does this come from starter to battery or the the black box next to battery?


the positive battery cable goes to the starter and the black box.there are some other wires involved with the pos cable. if your trying to replace it with a generic cable you cause more problems down the road than its worth.get a factory one at the dealer it will be easier to install and wont create problems

Apr 04, 2010 | 1994 Jeep Grand Cherokee

2 Answers

Battery cables


black (negative side) to ground. Other (red) should go to starter or starter relay

Mar 18, 2010 | 1992 Ford Ranger

2 Answers

1996 pontiac sunfire battery cables gone .


Positive goes to the starter motor and negative goes to the engine block for grounding.

Sep 01, 2009 | 1996 Pontiac Sunfire

Not finding what you are looking for?
2001 Chrysler Town & Country Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...