Question about 1992 Daihatsu Charade

Open Question

Carburetor Vacuum Charade 660CC Mira Pit

Hello friends...does any body has the vacuum hose dispossal for this car? 
Please, let me know at genarobuy@hotmail.com or ls-laser@hotmail.com
Thanks

Posted by on

  • 1 more comment 
  • Anonymous Feb 25, 2009

    I have an 660CC Mira Pit Charade. The vacuums are crazy, so the carburetor is working, but not tuned, and at morning works bad. Also, with the AC works bad.

    Do you have a picture so I can see were must be located each vacuum hose?

    Thnaks a lot budy

  • genarobuy Feb 25, 2009

    I have an 660CC Mira Pit Charade. The vacuums are crazy, so the carburetor is working, but not tuned, and at morning works bad. Also, with the AC works bad.

    Do you have a picture so I can see were must be located each vacuum hose?

    Thnaks a lot budy

  • yadayada
    yadayada May 11, 2010

    does any body has the vacuum hose dispossal, what do u mean by this?

×

1 Suggested Answer

Benimur
  • 6966 Answers

SOURCE: Daihatsu Mira 3 cyl 660cc No

Hi,

In my past dealings with these 3 cylinder engines, common faults (depending on the engine) are:

  • contact point pitting/burns (clean, scrape/replace);
  • rotor;
  • distributor cap;
  • ignition coil;
  • ignition coil ignition B+12 connector;
  • ignition coil loose ground.
Please check above mentioned components.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Posted on Aug 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vacuum hoses diagram


You will probably need to look at a repair manual for your Omni to find a vacuum diagram. Parts stores would sell them, public libraries might have them. If you have throttle body injection, the vacuum hoses are much simpler and fewer than if you had a carburetor with all those emission requirements for those years. I have an '87 Sentra, carbureted. Miles and miles of vacuum hoses !

Jan 01, 2014 | 1988 Dodge Omni

1 Answer

Mitsubishi vacuum diagram


hello
please answer me to khalajy2@yahoo.com
i have mitsubishi lancer with 4G13 motor and sndlw body (1992 year)
the carburator is single(is not electrical) the all hoses are moved and i dont now how to fixe them please help me for a plan or map of hoses of carburator(i am teacher in iran i can buy a lancer 1992 after 29 year teaching do you beleave this this is iran)
thanks

Aug 04, 2012 | Mitsubishi Cars & Trucks

1 Answer

Need a carburetor vacuum hose diagram 1983 dodge rampage


Vacuum diagram? - Turbo Dodge

www.turbododge.com > ... > Carburetted and TBI Injected . you should be able to find every thing you want to know here

Feb 04, 2012 | 1983 Dodge Pickup

1 Answer

My 92 charade se idles too high when engine is at normal temperature. When i adjust the big screw at the back of the carburator to the normal rev when it is warm it is ok but when the engine cools and i...


Hello and welcome to FixYa!

Just an insight regarding the problem. On cold start up, let it rev high till it reaches it's normal temperature, the idle will drop then when engine is warm so you can leave the breather adjustment screw in it's normal position.

If it still fails, then you can be facing vacuum leaks or there can be worn out vacuum hoses that needs replacement. If vacuum hoses are good then the problem can be on the carb itself. The gaskets can be worn out that's why you have irregularities on the carburetor's vacuum supply.

If that's the case. The carburetor gaskets must be replaced.

Hope this helps and thank you for using FixYa! Have a good one!

Apr 12, 2011 | 1992 Daihatsu Charade

1 Answer

1989 Mira Automatic stalls when coming to a stop unless I pull the choke out


Your idle fuel mixture it too lean. What this means is that it is not getting enough fuel at an idle. The most common reason for such problems are either problems with the linkage or vacuum lines or dirt or water in the carburetor. Make sure all your vacuum lines are good and connected, especially the one that goes to your distributor. Unless your fuel system has water in it or has had the filter removed and replaced with a hose, it is unlikely that the problem is the carburetor, unless the car has been sitting for a long time. Check these other things, first. Also, before your pull your carburetor off if these other things are not the problem, make sure your engine ignition has been properly tuned. Ignition problems are the most common problems on gasoline engines.

Feb 19, 2011 | 1989 Daihatsu Charade

1 Answer

Starts good, takes throttle, no idle.


Hello,
You may have idle jet is get problem or vacuum leaks. For temporary remedy, use a carburetor cleaner to clean your carburetor and found the vacuum leaks. For complete cleaning, dissemble your carburetor and have the jets, linkages cleaned. And check hoses linked to your carburetor for leakages.

Dec 10, 2010 | 1987 Toyota Corolla 2 Door

1 Answer

Where is the carb on a jeep grand cherokee 1993 4.0 liter


There is no carburetor on any of the 6 cylinder or 8 cylinder Jeep Grand Cherokees. They have Fuel Injection and a throttle body which looks like a carburetor scaled down.

---
Instructions on how to remove and replace the throttle body follow:

Throttle Body REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Remove the vacuum hoses from upper bonnet, unfasten the retaining clips and remove the upper bonnet assembly.
  3. Remove the lower bonnet retaining bolts and lower bonnet.
  4. Remove the throttle cable and the return spring.
  5. Disengage the wire harness connector from the injector.
  6. Disengage the wire harness connector from the WOT switch, ISA motor and TPS.
  7. Disconnect the fuel supply and return lines from the throttle body.
  8. Tag and disengage the vacuum hoses from the throttle body assembly.
  9. Disengage the potentiometer wire connector.
  10. Loosen throttle body retaining bolts and remove throttle body assembly from the intake manifold. To install:
  11. Clean the intake manifold and throttle body mating surfaces of old gasket material.
  12. Install a new gasket and the throttle body assembly. Tighten the mounting bolts to 16 ft. lbs. (21 Nm).
  13. Engage the potentiometer wire connector.
  14. Engage the vacuum hoses to the throttle body.
  15. Engage the fuel lines to the throttle body.
  16. Engage the WOT switch, ISA motor, TPS, and injector electrical connections.
  17. Install the return spring and throttle cable.
  18. Install the lower bonnet and fasten the retainers.
  19. Install the upper bonnet assembly, retaining clips and vacuum hoses.
  20. Connect the negative battery cable.
  21. Start the vehicle and check for fuel leaks. Fig. 1: Exploded view of the throttle body and related components 86745g41.gif
prev.gif next.gif

Aug 17, 2010 | 1993 Jeep Grand Cherokee

1 Answer

1991 charade G100, 3 cylinder, 2 door. I have disconnected all of the environmental control hoses from the carburettor and cannot recnnect them properly, I realy need a easily read diagram to show what ECS...


GO TO AUTO ZONE BUY THE CD- ROM. ALL DATA DIY .COM IT HAVE ALL ENGINE VACUUM DIAGRAM.AND DRIVE BELT ROUTING DIAGRAM FOR DIFFERENT CAR SERPERTINE BELTS.IT HAS ELECTRICAL DIAGRAMS ALSO.

Aug 29, 2009 | 1991 Daihatsu Charade

1 Answer

Specs for 1992 3cyl diahatsu charade ignition timing


Timing set with vacuum hoses disconnected and blocked is 5° advanced when flywheel dimple lines up with notch plate.

centrif wieghts 10.5° @ 2800
vacuum two stage 11° @ -320mmHg.

Feb 19, 2009 | 1992 Daihatsu Charade

Not finding what you are looking for?
1992 Daihatsu Charade Logo

Related Topics:

407 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daihatsu Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Daihatsu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...