Question about 1995 Jaguar XJ6

1 Answer

Need to replace the driver's door interior door opening assembly

How do I remove driver's door interior panel?

Posted by on

  • Anonymous Mar 13, 2014

    How to remove interior door panel on driver's side

  • Anonymous Mar 14, 2014

    need to access faulty door lock

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jaguar Master
  • 19,396 Answers

Hi there.

The procedure is roughly the same for all mk3 x types.
You need to remove all the screws on the armrest and on the ashtray, then undo all the plastic clips using screwdrivers on the panel.

You find detailed instructions on links below, I quote:

" remove two screws at the bottom of the armrest.
pull out ash tray.
remove screw in the middle of the ash tray holder.
pull up on armrest, it should pop up, then pull it out
start at bottom right of door and start popping out the plastic clips (all the way around the door)
(remove speaker wires)
push up door panel - done"



WikiAnswers - How do you remove a rear door panel in a Jaguar XJ6


Also from manual:

Disconnect vehicle battery ground lead.
Remove the door trim pad veneer panel.
Remove the upper trim pad.
Remove the door armrest.
From inside the door pocket, release the puddle lamp (1 Fig.1) securing quarter turn fastener.
Undo and remove fixing (3 Fig.1), (front door only)
Carefully release lower trim pad fir tree fasteners.
To avoid damage and distortion of the door metal, lift the lower trim pad complete with clip and clip retainer.
Carefully pull the trim pad away from the door panel.
Disconnect the multi-plugs (1 Fig.2) and remove the lamp.
Carefully displace the trim pad (2 Fig.1) from the door retaining clips.
Disconnect the multi-plugs (2 Fig.2) and (3 Fig.2).
Remove the door pocket.
Displace and remove the retaining clips and remove the trim..
Refit in the reverse order of the removal procedure. Check the trim pad retainers for damage before refitting.

Before refitting the lower trim pad, remove the clip retainer from the pad and and reposition retainer to the door.

ndo door handle escutcheon screw and remove escutcheon
Remove the door trim pad veneer panel.
Undo and remove the upper trim pad securing screws.
Remove the chrome strip.
Undo and remove the top channel securing nuts.
Displace and remove the top channel assembly.
Place the trim pad aside (Fig. 1).
Refit in the reverse order of the removal procedure.

Need to replace the driver's door interior door op - bbad647.gif



cc1f9fe.gif

Thanks Jaguar XJ6 Interior Lights

I will be grateful if you can rate the solution given.

Many thanks.

G.

Posted on Feb 25, 2009

  • bugeye600 Apr 10, 2011

    There is no advice on how to remove the panel (trim) directly below the arm rest, this panel needs to be removed to obtain access to the 2 screws holding the arm rest in position at the bottom

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the driver side door panel on a 1994 Lincoln Mark VIII


Remove mirror mount cover assembly.
Remove inside door handle cup (22634).
Remove door lock control bezel.
Remove window control bezel.
Remove interior lamp lens.
Remove screw from interior lamp assembly body.
Remove screw from window control bezel opening.
Disconnect mirror, lock switches and memory seat on driver side from bezels and wire harness.
Disconnect window switches from window bezel and wire harness.
Lift front door trim panel (23942) vertically, out of weatherstrip and over lock rod.
Disconnect interior lamp (13776) from wire harness.
Remove front and rear door trim retention hooks into door inner panel.
To install, reverse Removal procedure, paying special attention when inserting inner door trim into weatherstrip. Rock inner door trim into weatherstrip and push downward until lower trim belt character ditch lines up with score mark on inner door panel.

Aug 16, 2014 | 1994 Lincoln Mark VIII

1 Answer

Drivers side will not open from either side


There is a small spring in the locking/closing mechanism that is prone to break off. It is very difficult to get the door open once this happens, if you work with it enough you may get the door open so you can remove the interior door panel and replace it. It's just as easy to go to a salvage yard and purchase the entire lock assembly as trying to replace the spring. I had to cut a hole in the inner door to gain access but the door panel when replaced, covers it. This may be something you want a dealer or shop to do for you.

Mar 18, 2011 | Ford E-Series Cars & Trucks

1 Answer

Passat door 2006vw will not open from outside,but opens from inside


You need to get inside the door and reattach or replace the interior latch assembly that connects the handle to the latch release. This sounds like a lot of work but it really isn't and should take about 30 minutes to get the interior door panel off, repair the problem and get everything back together. The the door panel for any screws that maybe hidden under plastic caps and remove them. These are normally a #2 or #3 cross tip. Once those are removed use a flat screwdriver at the base of the door and pry up on the interior panel to separate the panel from the door, do this carefully and as you locate the push pins that hold the panel in place move the screwdriver close to the pin to do most of the prying. The closer you are to the pin the less damage is likely to happen to the door. These should pop out but are sometimes difficult. Once you have removed them the panel should lift off and you can access the latch mechanism and make repairs.

Feb 24, 2011 | 2006 Volkswagen Passat

1 Answer

Bracket for a grand wagoneer window on driver side. how do you install new peaces to hold window in place


The nylon gear track assembly that controls those window systems fail all the time. You've got to remove the interior door panel and most likely replace the gear track assembly. Once the panel is removed you can work on it through the cutouts in the door metal on the inside of the door. It's not easy to get to even with the panel removed. Good luck!

Dec 26, 2010 | AMC Wagoneer Cars & Trucks

1 Answer

Problem with dual zone heating only one side i check control thermost botton is ok


Sounds like the blend door actuator. It separates the driver and passenger side from getting air on the AZC system. Here are some instructions on replacing it:
The passenger side blend door actuator is used on all models equipped with Automatic Zone Control (AZC). This actuator is located on the front of the HVAC housing to the right of the floor panel transmission tunnel and cannot be removed from the passenger compartment without instrument panel or HVAC housing removal.

NOTE: This procedure is for AZC Systems (Passenger side only).

  1. Disconnect and isolate the battery negative cable.
  2. Remove the glove box door. See: Body and Frame\Interior Moulding / Trim
  3. Remove the lower I/P glove box door surround panel.
  4. Remove the dash assembly. See: Body and Frame\Interior Moulding / Trim\Dashboard / Instrument Panel\Service and Repair\Instrument Panel Assembly
  5. Remove the HVAC assembly. See: Housing Assembly HVAC\Service and Repair
  6. Unplug the wire harness connector from the blend door actuator.
  7. Remove the 2 screws that secure the blend door actuator to the HVAC housing.
  8. Remove the blend door actuator from the HVAC housing.
INSTALLATION - AZC (Passenger side only)


  1. In stall the blend door actuator on the HVAC housing and tighten the two mounting screws to 2.2 Nm (20 in. lbs.).
  2. Plug in the wire harness connector to the blend door actuator.
  3. In stall the HVAC unit into the vehicle. See: Housing Assembly HVAC\Service and Repair
  4. Install the instrument panel assembly into the vehicle. See: Body and Frame\Interior Moulding / Trim\Dashboard / Instrument Panel\Service and Repair\Instrument Panel Assembly
  5. Evacuate the HVAC system.
  6. Recharge the HVAC system.
  7. Connect and the battery negative cable.
Hope it helps! If you need more, just send me an email at familyguy77351 at yah I wil be glad to finish helping you with more detail.

Dec 12, 2010 | 2000 Jeep Grand Cherokee

2 Answers

The drivers front door will not open from the inside. The interior door handle won't activate the mechanism to open the door. Yet, the exterior door handle will open the door. Please advise! Thank you!


It could be the latch, but look to see if the interior door handle rod is still connected to the latch assembly. You will need to remove the interior door panel.

Jan 27, 2010 | 1995 Oldsmobile Cutlass Ciera

1 Answer

How do I remove the drivers window controls on a 2004 Mercedes Benz C240


Hi,

If you cannot see any bevelled edges to remove the master switch control, my suggestion would be the most common.... to remove all visible screws securing the interior panel to the door frame, e.g. behind door release handle, behind inside grip hande (as circled in photo), then slide & lift the interior door panel away slightly as one assembly, just enough to reveal any electrical wires.

Disconnect all wire looms from behind interior door panel...

Then, view switch assembly from behind the door panel, to determine best method to remove. Most modern switch assemblies are simply held in place by molded clips on the switch body, which need to be pushed out from behind.

36e466a.jpg

Cheers,

"If this has helped you in any way, please rate this solution"

Jan 25, 2010 | 2004 Mercedes-Benz C-Class

1 Answer

The interior door handle on the driver's side of my 2000 Tundra does not open the door. The exterior door handle works fine. I would assume the cable has broken on the door latch portion. What is the...


remove the screws that fasten the interior door panel to the door.  Visually inspect the handle assembly. there will be two cables that connect the handle and lock button to the door lock assembly.  I would bet that the L-shaped end of the interior door handle cable broke.  The replacement is self explanatory for the handle. Google the door lock assembly which isn't as visable.  Bob

Jan 10, 2010 | 2000 Toyota Tundra

1 Answer

Need to remove door interior panel on driver side of a 1989 Lincoln Mk VII to be able to repair the window open mechanism.


Door Panel
  1. Remove the retaining screws from the armrest assembly.
  2. Remove the screws retaining the switches to the housing and remove the cover assembly.
  3. Remove the door trim panel retaining screws.
  4. Using the trim pad removing tool, pry the trim panel retaining clips from the door inner panel.
  5. Disconnect all the wiring, if so equipped, and remove the trim panel.
To install:
  1. Position the trim panel to the door inner panel and connect the wiring, if so equipped.
  2. Push the trim panel and retaining clips into the inner door panel holes and install the retaining screws. Install the screws retaining the switches to the housing.
  3. Position the armrest to the trim panel, and install the retaining screws.

Dec 07, 2009 | 1989 Lincoln Mark VII

1 Answer

Drivers door wont open inside and outside on a 98 accord


You need to adjust or replace interior latch assembly. You can find out by removing interior door panel and inspecting latch assembly.

May 16, 2009 | 1998 Honda Accord

Not finding what you are looking for?
1995 Jaguar XJ6 Logo

1,657 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Raygin
Raygin

Level 2 Expert

322 Answers

yadayada
yadayada

Level 3 Expert

60960 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...