Question about 1993 Toyota Camry V6

2 Answers

Need instructions to replace 1993 Toyota Camry Timing Belt

Posted by on

  • 1 more comment 
  • Anonymous Mar 10, 2009

    1994 Camry, Cambelt snapped, I cant find the tensioner!!! : (

  • Anonymous Mar 19, 2009

    i need more help

  • Terry spearman May 08, 2013

    Thanks a bunch

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 39 Answers

Hi Kmcarroll77

TIMING BELT REPLACEMENT - 2.2L -1993 Toyota Camry

Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence. See Fig. 6 . On MR2, tighten engine
Need instructions to replace 1993 Toyota Camry - b7619be.jpg
92cabaf.jpg
Hope this helps, don't forget to rate.

Lazaruselite

Posted on Feb 25, 2009

  • Don Jones Sep 28, 2013

    thanks you were a big help. I have several manuals for many cars but didn't have this one. really appreciate your help!

×

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I can show u how to do it or email u instuctions. email me on atarikid@live.com

Posted on Mar 15, 2009

5 Suggested Answers

  • 1 Answer

SOURCE: i need a diagram of a 1991 toyota camry motor to replace a timing belt

some one directed me to autozone.com where i found what i was looking for. it is free once you register your car information. thank you so much.

Posted on May 19, 2009

emissionwiz
  • 60769 Answers

SOURCE: need marks for timimg belt

On the crankshaft gear there is a VERY small dimple that aligns with a mark on the motor. The mark on the motor (a small triangle) is at roughly 11 o'clock. After you line these timing marks up look at the camshaft gear and you will see that on one of the spokes there is a hole. You need to use a mirror to line this hole up with the dimple on the cover that is behind the camshaft gear. (It is at roughly 1 o'clock) If this hole is 180 degrees from where it should be you need to rotate the motor 1 more revolution at the crankshaft and it should now be lined up, or close. Once lined up I like to take a silver (metallic) Sharpie and make my own mark on the camshaft gear and on the backing plate that is behind it. You can make this mark where ever it is convenient for you. As long as you know where your marks line up, that is all that matters. This way I don't have to use the mirror as often.

  • Step 5 Once you have your timing marks aligned you need to locate the tensioner. The tensioner obviously keeps the appropriate amount of tension on the timing belt.
  • Posted on May 26, 2009

    • 101 Answers

    SOURCE: 1993 Toyota Camry V6 Timing Settings

    Get a T belt from toyota. It has 3 white lines on it and and arrow mark. 2 lines are solid and one is broken. Put the arrow facing away from the engine. The cam gears have a dot punched into them near a certain tooth. This is where the solid white lines will line up with. The crank gear will have a dot also. It will line up at 90 degrees from the top, towards the front of the car. This is where the broken line will match up with. With the belt installed with all lines on their proper dots and arrow away from the engine, you valve timming is correct.
    Of course you need to remove and compress the tensioner also. I assume you know this already since you didn't ask.

    Posted on Apr 16, 2009

    projdoc
    • 2236 Answers

    SOURCE: replace alternator belt only for 1993 toyota camry

    loosen the mounting bolts on the alternator, remove the old belt, replace with the new belt, slightly tighten the top mounting bolt, pull the alternator up until the belt is tight or if there is an adjustment bolt, crank down until tight (shouldn't bow more than 1"), and tigten other hardware.

    Posted on Aug 12, 2009

    • 285 Answers

    SOURCE: 2002 toyota timing belt replacement

    if this vehicle has the 2.4 ltr i has a chain,not a belt

    Posted on Sep 05, 2009

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Toyota Camry 1993 4 cyl water pump failing, have removed thermostat, considering Electric inline pump as replacement as option ? Please advise me of pro's and con's.


    i owned the 1995 4 cyl wide body camry till the cooling system failed in heavy traffic and over heat stripped out the head bolt threads in the block

    the toyota camry engine designation is a 5S-FE

    water pump is driven by timing belt
    behind timing belt covers
    they have to be removed to get to the water pump

    normally timing belt, seals ,tension er pully and water pump are replaced at the same time ..comes in a kit

    i dont have the 5S-FE cooling system hot under pressure specs

    so I cant answer which inline electric pump pressure is required to work on the 5S-FE


    engine repair manual free download pdf
    5S-FE 431 pages
    http://www.turboninjas.com/camry/eg1.pdf
    ENGINE MECHANICAL to page 144
    EMISSION CONTROL SYSTEMS
    MFI/SFI SYSTEM page 164
    COOLING SYSTEM page 238
    LUBRICATION SYSTEM page 268
    DIAGNOSIS SYSTEM page 296
    CIRCUIT INSPECTION page 336
    water pump as a part

    timing belt water pump kit
    water pump
    ,location on the engine with timing covers removed


    e7622159-98af-4a83-8989-bd6dd48bcde3.jpg26279563-dp42dlzfhn4dbdhi1rc14q4e-1-2.jpg26279563-dp42dlzfhn4dbdhi1rc14q4e-1-3.jpg

    Sep 10, 2016 | 1993 Toyota Camry

    1 Answer

    Do u have to change timing belt when u replace a water pump on 1993 camry


    Depending on the amount of miles on your vehicle it may be time to service the timing belt. Personally if it was me and I had to replace the water pump I would probable replace the timing belt at the same time since the cost is minimal. You can always check it for wear and cracks when you take it apart.

    Apr 02, 2014 | 1993 Toyota Camry V6

    1 Answer

    Instructions to replace 1994 toyota camry timing belt


    I have been trying to adjust my timing belt on my 94 camry. The timing is completely off so the car will not start. There are 2 indent marks and 2 spoke holes. The marks are 1 on the back cover and the other one is on the circle bit the belt goes around (sorry not good with car terms) and there and 2 spoke holes, one is see threw and the other is white. So having trouble working out what to line what with and do you line all of them the same. Please help. Thankyou.

    Jul 10, 2012 | 1993 Toyota Camry V6

    1 Answer

    Im replacing a timing belt on a 93 toyota camry 1.6 ltr. need instructions


    I would purchase a Haynes repair manual for this job the manual is $20.00 and is worth every penny for jobs like this, It would take 300 - 500 words on this forum for me to describe the procedure.

    Sep 11, 2009 | 1993 Toyota Camry V6

    1 Answer

    I need to know if the water pump freezing up can jar the timing belt loose. 2000 toyota camry le orgifly@yahoo.com


    The timing belt runs the water pump. If the pump bearing is bad, yes it could cause the timing belt to jump or even strip some of the teeth from the belt.

    Jul 14, 2009 | 1993 Toyota Camry V6

    1 Answer

    Car turns but wont start


    The mechanic is correct. Let him replace the timing belt for you.

    Jul 07, 2009 | 1993 Toyota Camry V6

    1 Answer

    Need instructions and illustrations to replace timming belt on a


    If you can tell me what engine you have I can try and send you the timing belt Illustration.

    Jun 26, 2009 | 1993 Toyota Camry V6

    1 Answer

    Timing belt needs to be replaced on a 4 cylinder 1993 toyota camry


    hi..The belt is accessed by removing the fan guard, fan
    and heater hoses.Then remove the belt covers.The lower
    cover will require you to remove the belt drive.once removed
    you can remove the old belt and reinstall it.
    try this out..
    thank u..
    kindly rate my response..

    Jun 09, 2009 | 1993 Toyota Camry V6

    Not finding what you are looking for?
    1993 Toyota Camry V6 Logo

    13,649 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    60667 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21936 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6811 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...