Question about 2006 Hyundai Tucson

1 Answer

Fog Lamp Bulb Replacement, 05 Tucson

I'm having truble getting at and replacing the fog lamp light bulbs on my 05 Hyundia Tucson. Does anyone know an easy way?

Posted by on

  • Anonymous Mar 23, 2014

    indicator and fog light working

  • Anonymous Mar 28, 2014

    2009 tucson parking light replace

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 67 Answers

Remove headlamp assembly and you can get it from the top pretty easy

Posted on Feb 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How hard is it to change a fog light bulb on a 2005 Subaru Forester? Can anyone do it?


Front Fog Light Assembly

REMOVAL


  1. Disconnect the ground cable from battery.
105919447



  1. Remove the two clips and lower mudguard on side that bulb is being changed.
  2. Disconnect the harness connector from bulb on back of fog lamp.
105919448




Front Fog Light Bulb

REMOVAL


1. Locate back cover on fog lamp assembly where bulb is located inside.

105919462



  1. Remove the back cover.
105919463



  1. Remove the spring retainer, and then detach the fog light bulb.
  2. DO NOT TOUCH HALOGEN BULB!! Oils from skin will cause bulb to explode during operation.

Jul 27, 2011 | Subaru Forester Cars & Trucks

2 Answers

How do you replace a fog light bulb on a 2005 hyundai tuscon"?


undo the hatch back {life the tail up as if you were wanting to gain access to the boot ..you will notice on either side both lighting clusters .depending on what side needs replacing .all you have to do it use a size 2 Philips screw driver to remove the black screws holding in the lighting clusters the locate the broken lamp{bulb} then twist the holder half a turn then replace the lamp {bulb} and then refit the cluster ..PLEASE note when you remove the screws you will have to gently ease the lighting cluster away from the body of the vehicle as if you try to rip it of you will damage it .there are two lugs that slide in to the bodywork of the car .make sure that you take a little time to locate them and check that the lighting cluster fits nicely to the vehicle before you replace the screws ..its worth trying the replacement lamp/bulb before you replace the screws ..just in case you have replaced a fault one with a faulty one !!! it can happen .

Jan 04, 2011 | 2005 Hyundai Tucson

1 Answer

How to replace a front fog lamp


  • If your fog lamp is connected to or behind a grille, pop it out. This can be done by first removing the clips or screws connecting it to the car and gently pulling it out. (If your fog lights are not connected to a grille, proceed to step 2.)Find the bolts that hold the fog lamp in place; you may have to get underneath the automobile to do so.Using your ratchet wrench, remove the bolts.4Grab the connector on the back of the fog lamp, turn it counter-clockwise and pull it out. This should remove the actual light bulb from the lamp fixture.Remove the fog lamp from the car and place the new one in.6Place the light bulb into the new fog light and turn clockwise to lock into place.Bolt the fog lamp back into place, if you had to remove the grille, put it back now and screw/clip it back into place.Turn on the fog lights and make sure everything is working properly


  • Oct 02, 2010 | 2004 Ford Explorer

    1 Answer

    How to change Ford Explorer fog light


    p, li { white-space: pre-wrap; }

    Open the hood and remove the electrical plug from the back of the fog light ballast below the headlight assembly.



    Turn the fog lamp counterclockwise to unlock it from the fog light housing.



    Insert the new fog lamp. Align the notches on the fog lamp housing with the tabs on the new bulb and turn the bulb clockwise to lock it into the housing.



    Reconnect the fog lamp electrical plug.

    Sep 13, 2010 | 1999 Ford Explorer

    1 Answer

    How do you replace the fog light bulbs on a 2004 buick regal?


    Notes FOG LAMP BULB REPLACEMENT - FRONT

    REMOVAL PROCEDURE
    f98bf40.gif
    1. Remove the front bumper fascia deflector.
    2. Disconnect the electrical connector from the front fog lamp bulb/socket. CAUTION: Refer to Halogen Bulb Caution in Service Precautions.
    01c84b0.gif
    1. Rotate the front fog lamp bulb/socket counterclockwise to release.
    2. Remove the fog lamp bulb/socket from the front fog lamp assembly.
    4065803.gif


    1. Install the fog lamp bulb/socket to the fog lamp rotating clockwise until fully seated. CAUTION: Refer to Halogen Bulb Caution in Service Precautions.
    b182709.gif
    1. Connect the electrical connector to the front fog lamp bulb/socket.
    2. Install the front bumper fascia deflector.

    Jun 16, 2009 | Buick Regal Cars & Trucks

    1 Answer

    Hyundai Sonata 2003 FOG LIGHTS DONT WORL


    No.. power is supplied to both bulbs in parallell... when power is present at one, it's also present at the other. Clarification needed - have you checked to see if you have power (battery voltage) and ground at the fog lamp connectors?.. if so, the problem is the bulb(s) it/them/self/selves. If you have an ohm meter or a test light, it's a simple procedure. Check the bulbs with an ohm meter. Then using a test light (12 volt, make sure the test light bulb is good by connecting it to a charges 12 v battery) connect the test light bulb to each of the fog lamp connectors with the fog lamp sw turned on and the ignition key in the 'run' position. If the test light illuminates at both fog lamp connectors, then the problem is in the fog lamp bulb(s) themselves. If not, there's a wiring/control circuit problem. You can go to http://www.hmaservice.com/ and register and gain access to lots and lots of technical info about your Sonata.

    May 26, 2009 | Hyundai Sonata Cars & Trucks

    1 Answer

    How to replace a fog lamp with replacement bulb only on 2002 toyota 4runner sport edition???? the three screws on the bottom?


    Well, these are the steps and I will post the pic here in a second...looks like 2 screws...but like I said, you can see the picture for direction on this.


    Remove or disconnect the following:

    Front turn signal lamp
  • Connector
  • 2 screws
  • 2 claw fittings
  • Fog lamp assembly
  • Fog lamp bulb as shown
  • Fog light unit

  • To Install
    1. Install or connect the following:
      • Fog light unit
      • Fog lamp bulb as shown
      • Fog lamp assembly latch the 2 claw fittings and 2 screws
      • Connector
      • Front turn signal lamp
    Trying to post the pics now....

    May 14, 2009 | 2002 Toyota 4Runner

    1 Answer

    Fog Lamp Bulb Replacement


    there are a couple of screws in the front of the fog light that will remove the lense so you can replace the bulb.

    May 11, 2009 | 2004 Chrysler Sebring

    1 Answer

    HOW TO REPLACE HEADLIGHTS ON 2000 CHRYSLER LHS


    ATTN: NIKKICARROLL

    here is how to replace the bulb in your vehicle


    1. Release the hood latch and open the hood.
    2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp.
    3. Remove the screws holding the headlamp module halves together.
    4. Separate the module halves.
    5. Disengage the wiring from the headlamp bulb.
    6. Remove the retaining ring from the back of the headlamp bulb.
    7. Pull the bulb from the lamp.
    To install:
    1. Push the bulb into the lamp.
    2. Install the retaining ring to hold the bulb in the lamp.
    3. Engage the wire connector to the back of the headlamp bulb.
    4. Place the module into position on the vehicle.
    5. Install the screws to hold the module to the vehicle.
    6. Install the radiator closure panel sight shield.
    7. Check the headlamp alignment and operation.
    88176gb1.gif Exploded view of the fog lamp with the bulb removed
    Click to Enlarge

    1. Release the hood latch and open the hood.
    2. Remove the radiator closure panel sight shield as needed to gain access to the headlamps.
    3. Remove the screws holding the headlamp module halves together.
    4. Separate the halves.
    5. Remove the fog lamp wire connector cover.
    6. Disconnect the wires from the fog lamp bulb.
    7. Disengage the retainer clip holding the bulb to the fog lamp.
    8. Remove the bulb from the fog lamp.
    To install:
    1. Place the bulb into position in the fog lamp.
    2. Engage the retainer clip to hold the bulb to the fog lamp assembly.
    3. Attach the wire connectors to the fog lamp bulb.
    4. Install the fog lamp wires connector cover.
    5. Place the module halves together.
    6. Install the screws to hold the headlamp module halves together.
    7. Install the radiator closure panel sight shield.
    8. Verify the fog lamp operation and alignment

    ATTN: WDSNEED1

    Removal & Installation 88176g87.gif Remove the screws retaining the headlamp module to the mount adapter
    Click to Enlarge

    1. Release the hood latch and open the hood.
    2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp fasteners.
    3. Remove the screws holding the headlamp module to the mount adapter.
    4. Separate the headlamp module from the mount adapter.
    5. Disengage the wiring from the headlamp and foglamp.
    6. Remove the headlamp from the vehicle.
    To install:
    1. Attach the wires to the headlamp and foglamp assembly.
    2. Place the headlamp module into position on the mount adapter.
    3. Install the screws to hold the headlamp module to the mount adapter.
    4. Install the radiator closure panel sight shield.
    5. Check the headlamp alignment and operation.

    Jul 28, 2008 | 1994 Chrysler New Yorker

    2 Answers

    Fog Light


    have you checked to make sure it's not just the bulb ? if it is there are likely two screws holding the lens on .... or you have to lay on your back and reach behind the light and see if you can remove the bulb that way....

    Robert

    Jul 17, 2008 | 2003 Mazda Protege

    Not finding what you are looking for?
    2006 Hyundai Tucson Logo

    517 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    yadayada
    yadayada

    Level 3 Expert

    60960 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...