Question about 2000 Ford F250 Super Duty Crew Cabs

2 Answers

2000 f350 shakes when hits a bump?

I a had my passenger baring changed and they had two rings that they couldt put back on, they told me i could run it like that so i did but then i hit a bump and it started shaking and broke my 4x4 hubs. I put some new ones on and was ok for two months and started again they told me it was the iner barings on the axel.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

Ok well there are no bearing on any axel. you may need to get the rite bearings or better ones. Or get really good ones you get wat you pay for always remember that

Posted on Feb 25, 2009

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 3 Answers

Steering stabilizer ?

Posted on Feb 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Ford F250 4x4 vibrates when it hit's a bump and then doesn't quit until you come to a stop or hit another bump


Steering shake ? Begin with have the steering & suspension expertly inspected & vehicle road tested....

Jul 03, 2014 | 2004 Ford Excursion

1 Answer

99 ford f150 4.2 started fine after getting at running temp. shuts off very hard to restart has code 320 changed crank sensor cam sensor no spark


The wiring harness which leads to the crankshaft sensor can rub on the A/C hose on the passenger side. When you restart the engine, it will shake and Torque the engine to the Drivers side until the RPM stabilizes. This will break contact with the bare wire until the wire settles back into position, ready to repeat the cycle. I imagine road bumps can have the same wire flopping around to cause intermittent failures again.

Try putting some electrical tape on the feed wire and then plastic tie the wire to give you clearance.

Mar 17, 2014 | 1999 Ford F150 Regular Cab

1 Answer

92 chevy c1500 shakes when braking or hits a bump


Thats called a shimmy. And you have shocks instead of struts.
Chances are you have a ball joint or tie rod end about to fail. Something is very loose in the front steering or suspension. I'd put money on it being a ball joint.

Sep 26, 2013 | Cars & Trucks

1 Answer

My car bounces whenever I hit a bump.


You need to change your STRUTS, depending on your Springs, you may need to change them too if you want a Smoother Ride

Apr 12, 2013 | Cars & Trucks

1 Answer

95 f-150 3 inch lift hit bumps at 35 mph and front shakes bad


Check your wheelbearings for play and your tierod ends for play,I'm sure one of these two are at fault.

Sep 25, 2009 | 1995 Ford F150 Styleside Regular Cab

2 Answers

Power shut off on ford f350 after hitting bump


is the battery connected or did the bump disconnect it?

Aug 31, 2009 | 2002 Ford F350 Super Duty DRW Reg. Cab

4 Answers

04 Dodge 2500 4X4 shakes violently after hitting bump at 55 mph +


The bumps do initiate the shaking. When my 2006 Ram 2500 4x4 started shaking, I had just had it aligned that morning. A month or so before that alignment, my passenger side outer tie-rod broke while driving down a rock road. I replaced it with a heavy duty MOOG tie-rod end. Anyway, the same day I had it aligned I was driving back home from a job and towing my bobcat behind me. I hit a bump and the truck did the "death wobble" with the front end shaking violently up and down in an alternating fashion (one tire in the air while one tire on the ground and then vice-versa). I changed the tires first (which were worn-out 305/75/17 mud tires). Since the day I bought the truck new in Jan. 2006, I've had larger tires on the truck than the tiny 235/75/17s that came with it and I've done a lot of heavy towing with it and never had a problem until this alignment was done at Sears. I;m still trying to figure out if it was the alignment specs that they used or if the problem coincidentally started that same day. I also changed the steering stabilizer. Neither the new tires nor the stabilizer/damper helped the problem. So I changed the other outer tie-rod end and the upper and lower ball joints (all MOOG with grease fittings). I turns out they were worn out. So, the truck no longer shakes violently up and down when I hit a bump. That problem seems to be in check. However, now when I hit a bump the truck's front end wobbles side-to-side. I can do a few things to recover from it. I can hit the brakes pretty hard and sudden (which can cause an accident on the interstate), or I can **** the steering wheel side-to-side a few times (from 10 o'clock to 2 o'clock) and that stops it immediately...until the next bump in the road. Also, if I let my foot off the accelerator just before hitting a bump and let the truck coast over it instead of power through it, sometimes the truck will ride over the bump without incident. I found out yesterday on a 5 1/2 hour road trip that if I did 80 to 90 miles per hour and powered through every road blemish, the truck rode fine...no shaking at all. I suppose the high speed forces the tires to stay straight when they hit a bump. Lastly, to confuse my problem solving attempts further, sometimes the truck rides like a cadillac (for an hour or so) at regular speeds and no matter what bumps I hit. Then without worning, the front end will loosen up and get that sloppy feeling again and the wobbling comes back at every bump...until the next time it feels like tightening up and driving right again. I have no idea what to do now. I'm going back to Sears today to have them check their alignment. Other than that, all I can think of is to change the rest of the steering components and check the steering box for malfunction. I hope someone can help all of us Dodge owners out off of the road tested info that I've just provided. Dodge doesn't seem to care to address the problems with their trucks front ends, and we need a solution before people get hurt or die. I was almost run over by an 18-wheeler trying to figure out how to handle the shake. I can't afford to buy another truck. So I need to fix this one so I can keep working. If anybody has a concrete solution to these problems, please let us know. I've read 20 different opinions from mechanics on these blogs, but nobody has said yet that they fixed someone's truck with these problems and have since heard from that customer and everything is still working fine. Opinions are helpful sometimes, but they're also confusing when they're conflicting.

Jun 24, 2009 | 1998 Dodge Ram 1500 4WD

2 Answers

My ac only works when i hit a huge bump and never again


I've had a similar problem. For me, the armature had some bad spots... or the bearings were going bad. So, I'd open the hood and tap the motor with a rubber mallet. Then, I'd reach through the open passenger window to feel if the air was coming from the vent. This would work very well until the blower motor finally went completely bad.

Apr 30, 2009 | 2000 Lincoln Town Car

Not finding what you are looking for?
2000 Ford F250 Super Duty Crew Cabs Logo

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...