Question about 2005 Toyota Camry Solara

Open Question

Steps to replace low beam headlight bulb solara 2005

Posted by on

  • Anonymous Apr 02, 2009

    Same basic problem except it's a 2000 Solara that I need the steps to replace the low beam headlight.

×

5 Suggested Answers

  • 2 Answers

SOURCE: Headlights

I READ ONLINE THAT THERE WAS A RECALL ON THIS YEAR AND MAKE, CHECK WITH TOYOTA WEB SITES TO RECTIFY YOUR PROBLEM

Posted on Jul 25, 2008

j_del
  • 1586 Answers

SOURCE: burned out headlight/bulb bmw 1991 325i 2dr

It's a bulb replacement. If it's anything similar to my Audi, there is a cover on the back of the headlight housing that you pop off. Then you can reach in, pull the wire connector off the bulb, and unclip a metal retainer over the bulb, and pull the bulb out. Installation of the new one is the reverse. Just be SURE not to touch the glass part of the bulb. Skin oils can cause a halogen bulb to burn very hot and burn out very quickly. If you do touch the glass, wipe it gently but thoroughly on a cotton cloth to clean it off before you install it.

Posted on Oct 31, 2008

  • 140 Answers

SOURCE: how do you resolve low beam bulb failure?

I CHECKED THIS ISSUE OUT FOR YOU. ALL YOU ARE REQUIRE TO DO IS REPLACE THE LOW BEAM.. GO TO ANY ADVANCED ATUO PARTS STORE AND PICK UP FOR ABOUT$13.. WHEN INSTALLING THE NEW LOW BEAM USE A RAG, OR CLOTH TO HANG ON THE GLASS OF THE NEW BULB..YOU CANT USE YOUR FINGERS TO PUT THE NEW BULB IN, THE OILS OFF OF YOUR FINGER TIP WILL MESS WITH THE LIFE OF THE NEW LOW BEAM... SHOULD BE A VERY SIMPLE TASK.. GOOD LUCK KEITH...

Posted on Mar 12, 2009

  • 10865 Answers

SOURCE: Low beam, driver's side headlight

The low beam bulb needs to be replaced. Go to an autozone store as they will sell you the bulb, and even assist you in their parking lot with installing it.

Posted on May 06, 2009

  • 1 Answer

SOURCE: how do you replace low beam right headlight

how do you replace the low beam lamp on the 2005 E320?

Thanx.

Posted on Jan 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i get to my low beams on my chrysler 2005 sebring sedan i got to the high beams perfect but the low beams right next to it has a metal barrier surrounding it which makes it impossible


Unfortunately, the answer I have is not a happy one =(. My wife has a 2005. In order to replace the bulb you will have to pull the Crutons (plastic push pins) that hold the front bumber cover on, remove the Headlight housing & replace the bulb that way. Shame on Chrysler for making it so difficult, in my opinion. But I hope this helps you to change the bulb =)

Aug 26, 2011 | 2004 Chrysler Sebring

1 Answer

I have a 2005 chev impala can i replace my high beams headlights with just low beam lights


NO YOU HAVE TO REPLACE HIGH BEAM LIGHT BULBS WITH HIGH BEAM LIGHT BULBS BECAUSE HIGH BEAM LIGHT BULBS AND LOW BEAM LIGHT BULBS TWO DIFFERENT TYPES OF BULBS.WEAR CLEAN LATEX GLOVES HANDLING THE HEADLIGHT BULBS WHICH IS HALOGEN LIGHT BULBS, OIL FROM FINGERS OR HAND WILL CAUSE HALOGEN BULBS TO OVER HEAT BLOW OUT.

Jul 05, 2011 | 2005 Chevrolet Impala

2 Answers

How do I replace the headlight bulb on a 2005 Town Car?


1. Remove the three pin-type retainers, two screws and the radiator defector.
2. Remove the 4 bolts securing the headlamp assembly and remove headlamp assembly.
- Disconnect electrical connector
3. Remove the 3 hex-head bolts and 2 torx-head screws and remove headlamp protective cover.
4. *****Standard low-beam bulb*****
Disconnect the connector from the bulb and remove the low beam bulb.
5. *****HID low beam bulb*****
Release the spring tabs and remove the HID low beam bulb
Disconnect the connector from the bulb
6. *****High beam bulb*****
Disconnect the electrical connector and remove the high beam bulb.
Reverse order to install
dttech_6.gif
.
.

dttech_7.gif

Jan 27, 2011 | 2005 Lincoln Town Car

1 Answer

How do I replace a headlight bulb in my 1996 Olds achieva


How to Replace a Headlight Bulb
(DIY Complexity: Easy / Time: 0.9 hour)

Parts:
1. Headlight Bulb

Tools:
1. Screwdriver
2. 1/4 in. Drive Ratchet
3. Socket Set

0fc6099.jpg

HIGH PERFORMANCE HALOGEN HEADLIGHT BULB -- Low 45/high 65 watts, Dual C-8 filament for both high beam and low beam; 100 percent legal halogen headlight bulbs; Features the whitest and brightest light color similar to daylight for safer night driving; Meets all US FMVSS 108 and Canadian CMVSS 108 requirements.

Steps:
Step 1 Open the hood and locate the headlight assembly.
o Tip: Most headlight assemblies have a place in the rear to gain access to the headlight bulb.
o Tip: It is recommended that headlight bulbs are replaced in pairs.
o Tip: Always make sure the struts on the hood can fully support the weight of the hood so that it does not close on you while working. The use of a hood prop can securely hold it in place.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 Gain access to headlight bulb.
o Tip: It is a good idea to check the high beam and low beam headlight bulbs at this time.

Step 3 Disconnect the wiring harness and replace the old headlight bulb with a new one.

35e674e.jpg

Remove the retaining ring from the base of the bulb, then...


99dfc4e.jpg

...turn the bulb and remove it from the headlight assembly.

Step 4 Turn on the headlights and check high and low beams to verify repairs.


Hope this help (remember comment and rated this).

Mar 30, 2010 | 1996 Oldsmobile Achieva

1 Answer

Need to replace headlight bulb 2007 hhr


H13 HALOGEN HEADLIGHT BULB, SOLD INDIVIDUALLY -- Low 55/high 65-watt halogen bulb; 12.8 volts; P26.4t base; A high quality, direct fit OE replacement headlight bulb

3c8c3dc.jpg


How to Replace a Headlight Bulb
(DIY Complexity: Easy / Time: 0.9 hour)

Parts:
1. Headlight Bulb

Tools:
1. Screwdriver
2. 1/4 in. Drive Ratchet
3. Socket Set

Steps:
Step 1 Open the hood and locate the headlight assembly.
o Tip: Most headlight assemblies have a place in the rear to gain access to the headlight bulb.
o Tip: It is recommended that headlight bulbs are replaced in pairs.
o Tip: Always make sure the struts on the hood can fully support the weight of the hood so that it does not close on you while working. The use of a hood prop can securely hold it in place.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 Gain access to headlight bulb.
o Tip: It is a good idea to check the high beam and low beam headlight bulbs at this time.

Step 3 Disconnect the wiring harness and replace the old headlight bulb with a new one.

Step 4 Turn on the headlights and check high and low beams to verify repairs.

Hope this help (remember rated this help). Good luck.

Mar 30, 2010 | 2008 Chevrolet Hhr

2 Answers

2005 kia sedona low beam headlight's don't work


CHECK THE BULBS, YOU MAY NEED TO REPLACE THEM, ALTHOUGH IT WOULD BE ODD THAT BOTH LOW BEAM SIDES OF THE BULBS WOULD BE BAD, ALSO CHECK YOUR FUSE BOX AND LOOK FOR THE LOW BEAM FUSE, MY SEDONA HAS ONE, YOURS MIGHT HAVE FUSED OUT

Jan 04, 2010 | 2003 Kia Sedona

1 Answer

Replacing headlights and adjustment


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jun 02, 2009 | 2005 Chevrolet Monte Carlo

1 Answer

2005 Honda CRV High Beam


Honda Headlight Bulb(H1) - This bulb is the high and low beam bulb for your vehicle. One bulb required for each headlight.

This headlight bulb fits:
  • CR-V 2005-2006 (requires 2 bulbs per side)

Mar 21, 2009 | 2005 Honda CR-V

1 Answer

How to change my headlights on Honda 2005 CRV


easy cheesy! Ive changed mine twice. The headlights are small bulbs. Make sure you get the right one (hi-beam vs low-beam). Unplug connector at back of bulb / headlamp unit, remove rubber weather seal (pops right ot). The bulb is held in with a small wire clip that is hard to get back on but can be done. Its spring loaded. Drop wire clip, turn bulb assya 1/4 turn, and it comes right out. Remove bulb from holder and replace. Reverse steps and VOILA!

Dec 27, 2008 | 2005 Honda CR-V

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,323 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...