Question about 1999 Ford Taurus

1 Answer

How do you replace passenger window in 99 ford taurus

I cant get the x bars to snap into the track on the bottem of the window

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 162 Answers

This is more a job for a contortionist than a member of public. you will find that at one position half down and half up(not exact) but you will be able to just about get your hands in enough to push them together. also yu should find a little chisle shaped thing in the ball and socket connection which you will have to pull out to enable them to go together, remembering to puish back in when connected.

Posted on Feb 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install replacement window on passenger side


you take off the door panel by using a panel clip tool to pop the clips for the panel to come off also check for any screws holding the panel to the door by the inside door handle the bottoms of the panel once you get it off unplug the window door switches to move the panel out of the way but first lower the window track so you can see it remove the weather seal plastic and then when you can get to the track and the glass you'll see that there should be yellow circle clips that pop together to hold the glass with rivets I'm assuming the glass is broken and this might have come off and is in the bottom of the door use these for the new glass after drilling out the old rivets snap them together one on each side of the new glass and then put bolts and nuts on to tighten or use a rivet gun to the track reconnect the switches for door window power and raise the glass

Feb 22, 2015 | 2004 Ford Taurus

2 Answers

I own a 99 Ford Taurus wagon. I can roll the rear window up & down but it won't go all the way up!! What causes this & can I fix it??


The window may be binding in the track and the motor is too weak to close it completely. Try cleaning the track. If that doesn't help the motor may need replacement

Jul 12, 2013 | Cars & Trucks

1 Answer

Passenger window


to me, it seems as if the window regulator is bad, wire snapped internal ,

Jul 08, 2009 | 1998 Buick Regal

1 Answer

OUTSIDE PASSENGER SIDE MIRROR. 2001 TAURUS


the Glass element or the glass and backing assembly? if just the glass it is just glued on, Scotch two sided tape works as well, if the Glass and backing fixture it just snaps in and out of the drive motors.

May 28, 2009 | 2001 Ford Taurus

2 Answers

Inner tie rod end on passenger side needs replaced


its not that hard its just a pain getting access to it as you will find the unit is tight and there is not a lot of room for leverage.

regards JR

May 27, 2009 | 1999 Ford Taurus

1 Answer

Replacing window motor


Start by disconnecting your negative battery cable. Then you need to locate and remove the screws that hold your interior door handles in place (they may be hidden by snap in, or snap on clips). Once you remove the screws that hold the door handles, remove any wire connectors to the handles. The door panel itself, is held on by snap in clips, and you will need a small pry bar to pull them from the door (try to get as close to, or directly under the clips to prevent them from tearing out of the door panel). Once the clips are removed from the door, pull the panel upward to remove it from the door. Once you gain access to the interior of the door, you will need to remove the motor and regulator as a single unit. Once you have removed the regulator you will be able to replace the motor.

Install in reverse.

I hope this helps you, and I wish you luck on your repair

May 10, 2009 | 1998 Ford Taurus

2 Answers

Snapped a bar that holds rear tire from moving front and back


yes you are right . and it can be replaced BUT i would look a little more.he may have a bent sturt and other parts.he hit the curb very hard to break the stablizer bar.

Mar 22, 2009 | 1992 Ford Taurus

1 Answer

1999 Ford Taurus passenger window button doesn't work


If all other window swtiches are working then that window switch needs to be replaced. Very simple to do. Good Luck

Dec 10, 2008 | 1999 Ford Taurus

1 Answer

Power window will not work


Test the window switch for proper operation at both switches, if neither works then you will have to replace the power window motor.

Oct 02, 2008 | 1999 Ford Taurus

Not finding what you are looking for?
1999 Ford Taurus Logo

Related Topics:

173 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...