Question about 1988 Toyota Pickup

1 Answer

How to remove the driver's interior door handle on a 93 Toy p-u?

See above...

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Large philips screw driver

Posted on Feb 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove door handle driver side 2009 pontiac g3


Remove the interior door panel and interior seal.

That will give you access to the back side of the door handle.
And your should be able to remove then.

Mar 12, 2015 | Pontiac Cars & Trucks

1 Answer

Why won't the inside Driver Door Handle work after being replaced


Make sure if it is equipped with a child safety lock on the inside of door jamb below or above the latch is unlocked. If that is ok then check to be sure the cable or rod to the interior handle is properly connected to the latch, remove door panel and if you can't see it directly you may have to use a mirror and flashlight to see if all is connected if so work the interior door handle while looking at all moving parts and tracking down where it is not doing it's function.

Aug 24, 2014 | 1998 Toyota Camry

1 Answer

How do I remove the interior door panel on a 93


remove screw and bolts holding your trimboards to its door panel using screw drivers covered its tip with masking tape to avoid damaging the trimboards upholstery and simply lift off the trim panel which light in construction.

Apr 07, 2010 | 1993 Nissan Pathfinder

2 Answers

The drivers front door will not open from the inside. The interior door handle won't activate the mechanism to open the door. Yet, the exterior door handle will open the door. Please advise! Thank you!


It could be the latch, but look to see if the interior door handle rod is still connected to the latch assembly. You will need to remove the interior door panel.

Jan 27, 2010 | 1995 Oldsmobile Cutlass Ciera

1 Answer

The interior door handle on the driver's side of my 2000 Tundra does not open the door. The exterior door handle works fine. I would assume the cable has broken on the door latch portion. What is the...


remove the screws that fasten the interior door panel to the door.  Visually inspect the handle assembly. there will be two cables that connect the handle and lock button to the door lock assembly.  I would bet that the L-shaped end of the interior door handle cable broke.  The replacement is self explanatory for the handle. Google the door lock assembly which isn't as visable.  Bob

Jan 10, 2010 | 2000 Toyota Tundra

1 Answer

How do I replace the driver's side door handle on a 2001 Chevy Tracker 4 door


Interior or exterior handle? Remove the door panel first. They make a special tool for removing the window crank, but usually you can get it off with a screwdriver. There is a little clip under the crank that needs to be removed first. Then remove the door handle itself, this has a screw in it. Then pull the panel off. With the window in the fully down position or the up position you should be able to get to the handle itself for the exterior. If it's an interior handle just remove that without taking the door handle off. This is all pretty self explanatory once you see it.

Dec 15, 2009 | 2001 Chevrolet Tracker

1 Answer

Door handle pulls but door doesn't open, 93 chevy lumina coupe 3.1 engine


Sounds like clip holding linkage(rod) may have come off, and linkage did the same because of it. You may have to remove interior door panel to investigate & re-attach.

Oct 28, 2009 | 1993 Chevrolet Lumina

1 Answer

Need directions to remove driver door interior panel 1997 deville


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Apr 21, 2009 | 1997 Cadillac DeVille

2 Answers

Removing interior door trim '93 suzuki swift


Assume you have been able to remove window winder.
The surround of the the door handle (interior) is clip on at four points. Tabs are about an inch in from each corner and slide over a plastic nub to lock in place. . Start at top right corner. Get a small flat blade screwdriver with blade horizontal and gently - repeat gently, prise tab upwards while applying gentle pressure away from door and pushing slightly upwards. Tab should just slide off nub holing it in place. Do same for other side on top tab. Gently wriggle downwards so bottom tabs disengage. Installation is reverse.

Sep 14, 2008 | 1993 Suzuki Swift

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...