Question about 2000 Ford Ranger SuperCab

2 Answers

Location of the egr sensor on 2000 ford ranger

Where is the egr sensor located on a 2000 ford ranger?

Posted by on

  • Anonymous Mar 17, 2014

    show location of egr sensor 401 code on 02 ford focus

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 22 Answers

The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

Posted on Feb 27, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 30 Answers

Look on the top of the engine. The EGR valve is usually shaped like a UFO with a vacuum line going from the top of it to the EGR valve sensor. That's how it is with my 4.0L SOHC. Hope this helps. God bless

Posted on Oct 23, 2009

  • flamerider
    flamerider Jun 08, 2012

    Thank you Adam it's folks like you that make the world a better place I appreciate your valuable time in answering my question. you answer has solved my problem Kindest Regards and God Bless you as well John

×

1 Suggested Answer

the recycler
  • 22 Answers

SOURCE: need location of the erg sensor 2000 ford ranger

The egr valve has two sensors. One is an EGR position sensor which is physically attached to the EGR valve. The other sensor is the DPFE (Delta Pressure Feedback EGR) sensor, commonly called the EGR pressure sensor. It's location varies depending on the engine you have. You can fine this sensor by following the vacuum hose on the EGR valve. It will be with in inches of the EGR valve. The sensor will be black (plastic) or silver (metal), have two or three vacuum ports and an electrical connection on it.

The vacuum pressure sensor is a high failure item on fords. Any Ford parts department will have one in stock, as well as some aftermarket parts stores.

The new sensor may not look exactly the same as the old part, but will have all the hook ups as the old one. You may also need to replace the vacuum hose to the sensor as well

Posted on Feb 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where egr dpfe sensor is located on a 2000 ford taurus


The EGR is on the Differential Pressure FEedback system. The EGR is located on top middle of the backside of the engine It is round and has a hose attached to it.

Sep 03, 2014 | 2000 Ford Taurus

1 Answer

Where is egrpressurefeedback sensor located on a 1999 ford ranger 2.5l


I believe it's on the right hand side near tranny dipstick. .simple thing to do is follow the egr steel exhaust tube from the back of the motor, the D.P.F.E will be off of that tube connected with 2 black rubber hoses and have a single electric connection.

May 09, 2014 | 2000 Ford Ranger SuperCab

1 Answer

I need to know if my 2003 ford ranger 3.0 liter engine has a egr valve and where is it located


yes you have egr valve
its on the passenger side of the motor back at the fire wall
you can also locate it by looking at you exhaust
you will see a tube that goes from the exhaust up the fire wall and into the egr hope this helps
give feed back

Dec 28, 2010 | 2003 Ford Ranger Regular Cab

2 Answers

Ford Ranger check engine light. I had it diagnosed as an EGR Valve, replaced it and the light cam back on after about 5 miles.


They all say the EGR valve is the problem but most of the time its the mass air fow meter is at fault.So i would recomend changing that.

Dec 29, 2009 | 2000 Ford Ranger SuperCab

1 Answer

2000 Ford Ranger- engine stalling when slowing down to idol


replace th air idle bypass valve this is located on the throtle body and has 2 screws with 1 plug with 2 wires to it

Dec 29, 2009 | 2000 Ford Ranger SuperCab

1 Answer

1996 ford ranger obd2 code 0402


check your egr valve its probably stuck open from carbon buildup and is letting too much exhaust recirculate you can take these off and clean them but with the age of your vehicle i would replace it

there is also a sensor that measures this that sometimes fails its called DPFE sensor it measures the amount of exhaust that is recirculate

not knowing what engine you have its hard to tell you ware the egr and DPFE sensor is located

May 17, 2009 | 1996 Ford Ranger SuperCab

2 Answers

Need location of the erg sensor 2000 ford ranger


The egr valve has two sensors. One is an EGR position sensor which is physically attached to the EGR valve. The other sensor is the DPFE (Delta Pressure Feedback EGR) sensor, commonly called the EGR pressure sensor. It's location varies depending on the engine you have. You can fine this sensor by following the vacuum hose on the EGR valve. It will be with in inches of the EGR valve. The sensor will be black (plastic) or silver (metal), have two or three vacuum ports and an electrical connection on it.

The vacuum pressure sensor is a high failure item on fords. Any Ford parts department will have one in stock, as well as some aftermarket parts stores.

The new sensor may not look exactly the same as the old part, but will have all the hook ups as the old one. You may also need to replace the vacuum hose to the sensor as well

Feb 24, 2009 | 2000 Ford Ranger SuperCab

2 Answers

Speed sensor diagram for 2000 ford ranger


This video shows the speed sensor and its location for a 2000 ford ranger xlt. It also describes the problems a bad sensor can give.

Nov 06, 2008 | 2000 Ford Ranger SuperCab

1 Answer

Diagrams


your oxygen sensor or sensors are located on your exhaust pipe just after your exhaust manifold

May 26, 2008 | 2000 Ford Ranger SuperCab

Not finding what you are looking for?
2000 Ford Ranger SuperCab Logo

Related Topics:

1,540 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...