Question about 2008 GMC Yukon

2 Answers

Remove battery from 99 yukon

I have never removed a battery that has the cables side mounted. Help I can not figure out how to remove the cable?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

Your gonna need either a 5/16 or 8mm wrench.  loosen the negative battery cable (black cable) off first and move it to the side where it wont touch the battery or anything metal.  then loosen and take off the positive (red) cable off and then just loosen the battery hold down bolt and the battery should left out. just like a top post battery make sure you dont touch anything metal with the wrench while loosing the bolts.

Posted on Feb 24, 2009

  • Andrew Davis
    Andrew Davis Mar 10, 2009

    i wouldnt use vise grips, you could end up stripping the bolts and causing yourself a world of trouble. you should be able to get it with the right size wrench without a problem.

×

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

You should be able to get the side mount terminal loose with a pair of vise grips, break it loose and it should be easy to get of by hand...take the black one - the negative side off first. if you can't get to it you may have to take the air box out, it should be 4 screws around the sides, pop it off, you should be able to wiggle the battery past tthe bottom.

Posted on Feb 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change alternator 2005 chryler 300


This answer covers:
2005 Chrysler 300 6cyl VIN "G" 3.5L SFI HO (72% of 2005 300's)
2005 Chrysler 300 6cyl VIN "R" 2.7L MFI DOHC (28% of 2005 300's)
2005 Dodge Magnum 5.7L engine

Alternator

Removal & Installation


WARNING - Precautions Section:
Disconnect negative cable from battery before removing battery output wire (b+ wire) from alternator. Failure to do so can result in injury or damage to electrical system.

2.7L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable.
  3. Remove alternator drive belt.
  4. Disconnect alternator field circuit plug.
  5. Remove B+ terminal nut and wire.
  6. Remove 2 lower mounting bolts.
  7. Remove alternator.
To install:
  1. Install alternator.
  2. Install upper bolt mounting bolt.
  3. Install 2 lower mounting bolts.
  4. Tighten bolts to 48 ft. lbs. (65 Nm).
  5. Install B+ terminal nut and wire. Tighten nut to 115 inch lbs. (13 Nm).
  6. Connect alternator field circuit plug.
  7. Install alternator drive belt.
  8. Connect negative battery cable.
3.5L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable.
  3. Remove alternator drive belt.
  4. Remove bracket bolts.
  5. Remove upper mounting bolt.
  6. Raise and support vehicle.
  7. Remove middle splash pan.
  8. Disconnect alternator field circuit plug.
  9. Remove B+ terminal nut and wire.
  10. Remove lower mounting bolts.
  11. Remove alternator.
To install:
  1. Install alternator.
  2. Install lower mounting bolts. Loosen install the upper mounting bolt.
  3. Tighten lower mounting bolts to 48 ft. lbs. (65 Nm).
  4. Connect alternator field circuit plug.
  5. Install B+ terminal nut and wire. Tighten nut to 115 inch lbs. (13 Nm).
  6. Install middle splash pan.
  7. Lower vehicle.
  8. Remove loose installed upper bolt.
  9. Install bracket and bracket bolt.
  10. Install upper mounting bolt and bracket.
  11. Tighten upper mounting bolt to 48 ft. lbs. (65 Nm).
  12. Tighten the bracket bolt to 40 ft. lbs. (54 Nm).
  13. Install alternator drive belt.
  14. Connect negative battery cable.
5.7L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable at battery.
  3. Remove alternator drive belt.
  4. Raise and support vehicle.
  5. Unsnap plastic insulator cap from B+ output terminal.
  6. Remove B+ terminal mounting nut at rear of alternator. Disconnect terminal from alternator.
  7. Disconnect field wire connector at rear of alternator by pushing on connector tab.
  8. Remove alternator support bracket nut and bolt. Remove support bracket. See Figure 1.
  9. Remove 2 alternator mounting bolts. See Figure 2.
  10. Remove alternator from vehicle.

Fig. 1 Alternator Support Bracket - 5.7L engine

7309257c-afe6-4c17-9422-d7fa2e3bd4b1.jpg

Fig. 2 Alternator Mounting Bolts - 5.7L engine

22b81ff7-7912-467f-9eaf-13ba2ff3a1a4.jpg

Oct 13, 2014 | 2005 Chrysler 300

1 Answer

How to put the Starter in a Eagle Talon 1991.


from autozone.com


REMOVAL & INSTALLATION
See Figures 5, 6, 7, 8, 9 and 10

  1. Disconnect the negative, then the positive battery cables from the battery.
  2. For 1990-94 vehicles, remove the battery and battery tray from the engine compartment.
  3. For 1990-94 vehicles, detach the speedometer cable connector from the transaxle.
  4. For 1995-98 2.0L turbo engines, remove the air hose.
  5. For 1995-98 2.4L engines, remove the air cleaner and air intake hose.
  6. If equipped with 1.8L engine, remove the bracket on the lower side if the intake manifold.
  7. Detach the starter motor electrical connections.
6f8c23b.gif

Fig. Fig. 5: Exploded view of the starter motor and related components-1990-94 vehicles, others similar


458b681.gif

Fig. Fig. 6: Unfasten the BAT terminal connector from the starter motor


05a1691.gif

Fig. Fig. 7: Unplug the starter motor electrical connector

  1. Unfasten the starter motor mounting bolts, then remove the starter from the vehicle.
d0adab9.gif

Fig. Fig. 8: Unfasten the starter mounting bolts
d00c214.gif

Fig. Fig. 9: Remove all of the starter mounting bolts ...
c92a470.gif

Fig. Fig. 10: ... then remove the starter motor from the vehicle
To install:

  1. Clean both surfaces of starter motor flange and rear plate. Install the starter motor onto the engine and secure with the retainer bolts. Tighten the retainers to the specifications shown in the accompanying figure.
  2. Attach the electrical harness connector(s) to the starter.
  3. If removed, install the intake manifold stay and tighten the retainers to 18 ft. lbs. (25 Nm).
  4. For 1995-98 2.4L engines, install the air cleaner and air intake hose.
  5. For 1995-98 2.0L turbo engines, install the air hose.
  6. For 1990-94 vehicles, attach the speedometer cable to the transaxle. Install the battery tray and battery.
  7. Connect the positive, then the negative battery cables.
Operate the starter to assure proper operation.

Oct 29, 2010 | 1991 Eagle Talon

1 Answer

1997 golf need to see a picture of where the fuel pump and fuel filter is located...non turbo


Filter: Under hood, driver side, front side of strut tower, rear of battery, mounted on fender in fuel line
Pump: inside fuel tank but accessible from inside the car--see procedure below from autozone.com.

1993-99 Cabrio, Golf, and Jetta

  1. Remove the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Relieve the fuel system pressure.
  4. Remove the rear seat and the access cover.
  5. Disconnect the wiring and hoses.
  6. Remove the fuel lines from the pump.
  7. On 1993-99 Golf, Jetta and Cabrio vehicles, unscrew the fuel pump retaining ring.
  8. On all other models, remove the mounting bolts and the fuel pump.
  9. Carefully lift out the pump and gauge sending unit assembly.
  10. Empty the fuel pump into an approved container

Sep 18, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

99 ford contour hazard flasher unit where is it


Flashers - REPLACEMENT

Turn Signal Flasher
(see Figure 1)

e21631a.jpg

Fig. 1: The turn signal flasher is located on the multi-function switch in the steering column
  1. Disconnect the negative battery cable.
  2. Remove the upper and lower steering column shrouds.
  3. Pull the flasher from the back of the multi-function switch.

To install:
  1. Install a new flasher in the multi-function switch.
  2. Install the column shrouds.
  3. Connect the negative battery cable.

Hazard Warning Flasher
  1. Disconnect the negative battery cable.
  2. Remove the knee bolster panel from the underside of the driver's side of the instrument panel.
  3. Grasp and pull the flasher from the connector located near the top of the steering column.

To install:
  1. Install a new flasher in the connector.
  2. Install the knee bolster panel.
  3. Connect the negative battery cable.

Hope this help (remember comment and rated this).

Apr 02, 2010 | Ford Contour Cars & Trucks

1 Answer

I need a diagram to find my aluternator in my 1998 dodge strstus please.


2.0L DOHC Engine
See Figure 4
  1. Disconnect the negative battery cable.
  2. Disconnect the starter motor electrical connections.
  3. Remove the starter motor mounting bolts and remove the starter.


cb88b61.jpg Fig. Fig. 4: Exploded view of the starter motor mounting-2.0L engine
To install:
  1. Clean both surfaces of the starter motor flange and the rear plate. This is important since the starter grounds through its case and the transaxle flange to which it attached. Some remanufactured starters may have paint on these areas which should be cleaned off before installation. Install the starter motor onto the transaxle and secure with the retaining bolts. Tighten the bolts to 40 ft. lbs. (54 Nm).
  2. Attach the electrical harness connectors to the starter.
  3. Connect the negative battery cable and check the starter for proper operation.

2.0L SOHC Engine With Manual Transaxle
See Figures 4 and 5
  1. Disconnect the negative battery cable from the left strut tower. The ground cable is equipped with a insulator grommet which should be placed on the stud to prevent the negative battery cable from accidentally grounding.
  2. Remove the air cleaner resonator.
  3. Remove the positive battery cable retaining nut from the starter.
  4. Disconnect the positive battery cable and alternator output wire from the starter.
  5. Disconnect the push-on solenoid connector from the starter.
  6. Remove the 2 bolts that attach the starter to the transaxle.
  7. Remove the starter from the vehicle.

14f147d.gif

Fig. Fig. 5: Starter motor wiring terminal connections-2.0L engine To install:
  1. Install the starter and the attaching bolts to the transaxle assembly.
  2. Tighten the attaching bolts to 40 ft. lbs. (54 Nm).

Clean all dirt and/or corrosion from the wire terminals before reconnecting the wiring to the solenoid.
  1. Reconnect the push-on solenoid connector to the starter.
  2. Reconnect the alternator output wire and positive battery cable to the starter and tighten the retaining nut to 90 inch lbs. (10 Nm).
  3. Install the air cleaner resonator.
  4. Reconnect the negative battery cable.

2.0L SOHC Engine With Automatic Transaxle; 2.4L Engine
See Figures 4, 5 and 6
  1. Disconnect the negative battery cable from the left strut tower. The ground cable is equipped with a insulator grommet which should be placed on the stud to prevent the negative battery cable from accidentally grounding.
  2. Remove the air cleaner resonator.
  3. Remove the 3 bolts attaching the Transmission Control Module (TCM). Do not disconnect the TCM wiring. Move the TCM to gain access to the upper starter mounting bolt.
  4. Remove the upper starter mounting bolt.
  5. Raise and safely support the vehicle.
  6. Remove the positive battery cable nut and disconnect the cable from the starter.
  7. Disconnect the push-on solenoid connector.
  8. Remove the lower mounting bolt that attaches the starter to the transaxle.
  9. Remove the starter from the vehicle.


2f4680e.jpg

Fig. Fig. 6: Starter motor wiring terminal connections-2.0L SOHC engine with A/T; 2.4L engine To install:
  1. Install the starter onto the transaxle and the lower mounting bolt.
  2. Tighten the mounting bolts to 40 ft. lbs. (54 Nm).
Before reconnecting the wiring to the starter solenoid, be sure to clean the wiring of any dirt or corrosion.
  1. Reconnect the positive battery cable to the solenoid post and tighten the retaining nut to 90 inch lbs. (10 Nm).
  2. Reconnect the push-on solenoid connector.
  3. Lower the vehicle.
  4. Reinstall the upper attaching bolt and torque to 40 ft. lbs. (54 Nm).
  5. Reinstall the TCM to its original location and install the mounting screws.
  6. Reinstall the air cleaner resonator.
  7. Reconnect the negative battery cable

Hope helped.

Feb 01, 2010 | 1998 Dodge Stratus

1 Answer

NEED TO INSTALL SARTER ON 1997 EXPLORER ALL WHEEL DRIVE


  1. Disconnect the negative battery cable.
  2. Raise the front of the vehicle and install jackstands beneath the frame. Firmly apply the parking brake and place blocks in back of the rear wheels.



  1. Tag and disconnect the wiring at the starter.


WARNING When detaching the hardshell connector at the S-terminal, grasp the plastic shell to pull it off. Do not pull on the wire itself. Ensure to pull the connector straight off to prevent damage to the connector and S-terminal. If any part of the connector is damaged, replace the damaged component.


  1. Remove the starter mounting bolts and remove the starter.





To install:
  1. Position the starter motor against the engine and install the mounting bolts. Tighten the mounting bolts to 15-19 ft. lbs. (21-27 Nm).
  2. Install the starter solenoid connector by pushing it straight on. Ensure that the connector locks in position with a notable click.

Install the starter cable nut to the starter solenoid B-terminal. Tighten the nut to 80-123 inch lbs. (9-14 Nm).
  1. Connect any remaining wiring to the starter motor.
  2. Lower the front of the vehicle and remove the wheel blocks.
  3. Connect the negative battery cable.

RELAY REPLACEMENT

See Figures 7 through 13
  1. Disconnect the negative battery cable from the battery.
  2. If necessary, remove the power distribution box cover.



0900c1528018eb98.jpg
  1. Disconnect the positive battery cable from the battery terminal.
  2. Remove the nut securing the positive battery cable to the relay.



0900c1528018eb9b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 10: Remove the cable securing nuts ...
  1. Remove the positive cable and any other wiring under that cable.





Fig. Fig. 11: ... then remove all of the cables from the relay
  1. Label and remove the push-on wires from the front of the relay.
  2. Remove the nut and disconnect the cable from the starter side of the relay.





Fig. Fig. 12: Remove the relay-to-fender apron attaching screws ...




Fig. Fig. 13: ... then remove the relay from the fender
  1. Remove the relay mounting bolts and remove the relay.

To install:
  1. Install the relay and mounting bolts. Tighten the mounting bolts until snug.
  2. Attach all wiring to the relay.
  3. If equipped, install the power distribution box cover.
  4. Connect the positive (+) cable to the battery.
  5. Connect the negative (-) cable to the battery.

Nov 11, 2009 | 1997 Ford Explorer AWD

1 Answer

To remove an alternator on a 1998-99 Intrepid, on drivers side


FIRST OF ALL.TURN OFF RADIO SO YOU WONT LOSE RADIO CODE.FOR THE 2.7L ENGINE.DISCONNECT NEGATIVE BATTERY CABLE.REMOVE THE LOWER PLASTIC SPLASH SHIELD.REMOVE TRANSMISSION COOLER AND POSITION IT ASIDE.REMOVE THE LOWER RADIATOR CROSSMEMBER SUPPORT.LOOSEN BUT DO NOT REMOVE.ADJUSTING T BOLT AND THE PIVOT BOLT.LOOSEN DRIVE BELT ADJUSTING BOLT.REMOVE OR DISCONNECT THE FOLLOWING.DRIVE BELT.REMOVE ALTERNATOR ELECTRICAL WIRES.REMOVE PIVOT BOLT CAREFUL NOT TO LOSE THE SPACER.REMOVE THE ALTERNATOR. NOW THE 3.2L AND 3.5L ENGINES REMOVE THE NEGATIVE BATTERY CABLE.THEN REMOVE THE LOWER MOUNTING BOLT AND PIVIT BOLT.REMOVE DRIVE BELTTENSION BOLT THEN DRIVE BELT.REMOVE BRACKET LOWER MOUNTING BOLT AND PIVOT BOLT.THEN REMOVE THE ALTERNATOR + ALTERNATOR FIELD CIRCUIT PLUG + ALTERNATOR B+ TERMINAL NUT AND WIRE.THEN PUT EVERYTHING BACK VISA VERSA.

Sep 18, 2009 | 1999 Dodge Intrepid

2 Answers

Replacement of the serpentine belt on 1997 buick lesaber how


Yes, I have a 97 buick and the motor mount does have to be removed. See information below that I retireved from Autozone.com:

REMOVAL & INSTALLATION
See Figures 7 through 13
  1. Disconnect the negative battery cable.
0900c152800b19a8.jpgFig. 7: Many vehicles have an accessory drive belt routing label affixed to the radiator shroud
  1. Remove the belt guard or coolant recovery reservoir as required.
  2. For 1996-99 supercharged engines, perform the following:
    1. Raise and safely support the vehicle.
    2. Remove the right-hand splash shield.
    3. Remove the connector from the crank sensor.
  3. For 1996-99 vehicles, remove the engine mounting bracket lower nut, stud and spacer. Carefully lower the vehicle.

Jan 25, 2009 | 1997 Buick LeSabre

1 Answer

Headlight switch


REMOVAL & INSTALLATION
See Figures 1 and 2
  1. Disconnect the battery ground cable.
  2. On 1991-94 models, perform the following:
    1. Remove the ash tray assembly and the finish panel (snaps off).
    2. On the Explorer, remove the rear window wiper and heated backlite switch assembly (snaps out).
    3. On the Ranger, remove the storage bin (snaps out).
    4. Pull the headlight switch knob to the headlight on position. Depress the shaft release button and remove the knob and shaft assembly. 0900c1528018ef70.jpgFig. 1: View of the 1991-94 model headlight switch control knob release button
  3. On 1995-99 models, remove the instrument panel finish panel.
  4. Unscrew the mounting nut and remove the switch from the instrument panel, then remove the wiring connector from the switch.
0900c1528018ef71.jpgFig. 2: Exploded view of the 1995-99 model headlight switch componentsTo install:
  1. Connect the wiring connector to the headlamp switch, position the switch in the instrument panel and install the mounting nut.
  2. On 1995-99 models, install the instrument panel finish panel.
  3. On 1991-94 models, perform the following:
    1. Install the headlamp switch knob and shaft assembly by pushing the shaft into the switch until it locks into position.
    2. On the Explorer, install the rear window wiper and heated backlite switch assembly.
    3. On the Ranger, install the storage bin.
    4. Install the finish panel and the ash tray assembly.
  4. Connect the battery ground cable, and check the operation of the headlight switch.

Nov 29, 2008 | 1998 Ford Explorer

2 Answers

Changing the starter on my 99 tahoe


Starter Escalade, Suburban, Tahoe, Yukon, Denali, Denali XL, Yukon XL, 1999 – 2005 REMOVAL&INSTALLATION
Removal & Installation
4.8L, 5.3L And 6.0L Engines
CAUTION Before servicing any electrical component, the ignition key must be in the OFF or LOCK position and all electrical loads must be OFF, unless instructed otherwise in these procedures.
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle.
  3. Remove or disconnect the following:
    • Protective shields, as necessary
    • Starter solenoid shield
    • Starter-to-transmission close out cover bolt
    • Engine oil level sensor connection
    • On 4WD, front axle mounting bracket through bolt nut
  4. Reposition the front axle mounting bracket through bolt until the bolt tip is flush with the support bushing. Do not remove the bolt.
    • Mounting bolts from the engine block. Slide the starter forward until the starter clears the transmission.
    • Starter transmission close out cover
    • Positive battery cable and wiring harness from the starter
    • Starter from the vehicle 0900c152800a6916.jpgStarter removal—4.8L, 5.3L and 6.0L engines
To install:
  1. Install or connect the following:
    • Starter
    • Positive battery cable to the starter. Tighten the nut to 12 ft. lbs. (16 Nm).
    • Starter transmission close out cover
    • Mounting bolts to the engine block and tighten to 37 ft. lbs. (50 Nm)
  2. Reposition the front axle mounting bracket through bolt until the bolt is fully seated.
    • Front axle mounting bracket through bolt nut and tighten to 70 ft. lbs. (95 Nm)
    • Engine oil level sensor connection
    • Starter-to-transmission close out cover bolt
    • Starter solenoid shield
    • Protective shields as necessary
  3. Remove the safety stands.
  4. Lower the vehicle.
  5. Connect the negative battery cable.
5.7L And 7.4L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Mounting bolts and shims
    • Wires
    • Heat shield
    • Starter
To install:
  1. Install or connect the following:
    • Starter
    • Wires. Torque battery wire nut to 89 inch lbs. (10 Nm), and ignition nut to 18 inch lbs. (2 Nm).
    • Heat shield. Torque the bolts to 53 inch lbs. (6 Nm) and the nuts to 35 inch lbs. (3 Nm).
    • Mounting bolts and shim. Torque the bolts to 33 ft lbs. (45 Nm).
    • Negative battery cable
6.5L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cables
    • Mounting bolts/nuts and shim, if used
    • Starter
    • Wires
    • Heat shield and bracket 0900c152800a6917.jpgExploded view of the starter motor—6.5L engine
To install:
  1. Install or connect the following:
    • Heat shield and bracket. Torque the bolts to 13 ft lbs. (17 Nm).
    • Wires. Torque battery wire nut to 89 inch lbs. (10 Nm), and ignition nut to 18 inch lbs. (2 Nm).
    • Starter
    • Mounting bolts/nuts and shim, if used. Torque the bolts to 33 ft lbs. (45 Nm) and the nut to 75 inch lbs. (8.5 Nm).
    • Negative battery cables
8.1L Engine
  1. Remove or disconnect the following:
    • Negative battery cable
    • On 4WD, front axle mounting bracket through bolt nut
  2. Reposition the front axle mounting bracket through bolt until the bolt tip is flush with the support bushing. Do not remove the bolt.
    • Positive battery cable nut
    • Positive cable from the solenoid
    • Engine harness ground nut and ground from the solenoid
    • Mounting bolts and starter
    • Heat shield bolts, nut and shield, if necessary
To install:
  1. Install or connect the following:
    • Heat shield, bolts and nut if removed. Tighten the bolts to 35 inch lbs. (3 Nm) and the nut to 44 inch lbs. (5 Nm).
    • Starter and bolts. Tighten to 37 ft. lbs. (50 Nm).
    • Ground wire and nut. Tighten to 30 inch lbs. (3.4 Nm).
    • Positive cable and nut. Tighten to 80 inch lbs. (9 Nm).
  2. Reposition the front axle mounting bracket through bolt until the bolt is fully seated.
    • Front axle mounting bracket through bolt nut and tighten to 70 ft. lbs. (95 Nm)
    • Negative battery cable

Sep 28, 2008 | 1999 Chevrolet Tahoe

Not finding what you are looking for?
2008 GMC Yukon Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...