Question about 1995 Ford Aerostar

1 Answer

Engine almost dies when applying brake pedal. Battery dead.

1995 Ford Aerostar 3.0

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Ford Master
  • 2,007 Answers

Broken or loose vacuum line. Check all your vacuum lines with the engine running. Listen closely for air. Wiggle them around and see if anything changes.

Posted on Feb 24, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I fix a stickiing accelerator pedal on a 1995 Ford Aerostar

Just spray some penetrating oil on the pivot joint of pedal lever. It will free up.

Sep 24, 2014 | 1995 Ford Aerostar

1 Answer

What does the btsi seloide look like

Check the release cable. There is a cable that activates when you press down on the brake pedal. This allows it to shift. So if you are depressing the brake pedal and it won't release, check that cable.

Aug 05, 2014 | 1995 Ford Aerostar

1 Answer

Is it modulator valve, or other?

The vac modulator only assists the transmission in knowing when to shift up.
If the engine oil pressure gauge is acting wildly, it could be the sensor or the oil pressure could really be going up and down.

Feb 23, 2014 | 1994 Ford Aerostar Extended

1 Answer

Brakes apply themselves

by the sound of this the brake booster is leaking fix the vacuum leak or replace the brake booster and all will be ok

Feb 16, 2012 | 1987 Ford Ranger

1 Answer

Firingorder and #1 position on the distributor for a 95 ford aerostar 3.0 v6

For the 1995 Ford Aerostar Van:

For the 3.0L V6:
Firing Order:
Ignition Coil Connections:
2...6-This is correct!

Aug 28, 2010 | 1995 Ford Aerostar

1 Answer

My amp light came on and twice it has not wanted to start. I removed and cleaned terminals on 1995 ford aerostar. now it will not start? Oct and 9 are punched on top of battery does that mean 1999? How do...

If your amp light was on before it died I would say it is your alternator. Recharge the battery. Then it should start. Then have the alternator checked.

Jun 23, 2010 | 1995 Ford Aerostar

2 Answers


try bleeding themm when done front driver side then crisscross back passangerside then front passenger and last but not least back driver side. get all air out if that dont do it you have a vaccumm leak one small vaccum line can have a dramatic effect

Jan 24, 2010 | 1995 Ford Aerostar

2 Answers

There is no brake lights and its very hard to shift to drive

brake switch located under dash just in front of the brake pedal arm.... I just replaced mine

Oct 12, 2009 | 1995 Ford Aerostar

1 Answer

1993 Ford AWD Aerostar Van. When the engine is

Sounds like the front calipers are not fully retracting properly. Check the front caliper operation while a friend pumps the brake pedal, the rubber lines could also be cracked and allowing air into the lines. Check brake fluid level.

Aug 29, 2009 | 1993 Ford Aerostar Extended

Not finding what you are looking for?
1995 Ford Aerostar Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

5623 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides