Question about 1987 Chevrolet Astro Cargo

Open Question

4.3 V 6 with no ac or airpump need Belt tentioner and braket

Hi I hope someone can help me. I installed a 1987 Chevy 4.3 V 6 out of an Astro in my Jeep Wrangler. I removed the AC , and Air Pump. I need the braket that holds the serpentine belt tentioner. I bought the tentioner at Advance Auto parts. Part number 89227. I need the braket that bolts on and holds this tentioner..Please Help..JB

Posted by on

6 Suggested Answers

Mike258
  • 1498 Answers

SOURCE: 1993 jeep wrangler 4cyl -serpentine belt digram

f45e20e.jpg

Hope this helps,

Mike

Posted on Jul 14, 2008


dgjtex
  • 405 Answers

SOURCE: chevy silverado 2000 serpentine belt replacement?

Mike, the belt routing should be on a sticker under your hood, these use a spring belt tensioner and it is easiest to us a 3/8 or 1/2 breakover to pull the tensioner back then the belt is easily removed and replaced, please do not rate me at all if it is not a fixya, thats the only reason do this is for my score. Thanks, and merry Christmas.

Posted on Dec 22, 2008

  • 1 Answer

SOURCE: 1987 jeep wrangler

I have the Haynes repair manual 1987-2003 Jeep Wrangler with all of the schematics. Which wiring scematics do you need and maybe I can scan/email the pages, if this legal? Or can maybe answer questions you may have, keeping in mind I am NOT a mechanic but I can read plans/schematics

Posted on Apr 06, 2009

polarcycle
  • 1392 Answers

SOURCE: how to replace a serpentine belt on 1998 jeep wrangler

Should be the pulley underneath the power steering pulley. Loosen the nut, then back the bolt down the loosen the belt, tighten the bolt to tighten belt.

Posted on Jul 14, 2009

AUTODOC01
  • 216 Answers

SOURCE: 1993 chevy van g20 water pump replacement

you will need some fairly long wrenchs 15mm-16mm to get leverage on the spring loaded serp tesiner put a wrench on the pulley near the belt ? also loosen the 4 fan bolts on the water pump before you remove the belt ? ther are 7 fan shroud bolts you can split the fan shroud ? 2 bolts on the lower right and 2 on the left ? after you do this then you should be down to pulling off the fan and pulley just slides off ? then remove the 4 waterpump mounting boltss, scrape the old gaskets ? when this is done all you have left is to installthe fan studs from the old pump? you do this by screwing down 2 nuts on the stud then with 2 wrenchs lock the nuts together ? then unscrew the bottom nut ? keep doing that till all 4 are replaced? install the gaskets and add some silicone and reverse the process ? hope this helps repost thumbs up !!

Posted on Aug 29, 2009

  • 57 Answers

SOURCE: The blinker stick broke off in my 1987 Jeep Wrangler.

remove steering wheel-and shroud then unscrew blinker assy and uplug wires-replace with new assembly-inless you can bodgey up with araldite or similar

Posted on Sep 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove the fan to replace the serpentine belt


do not remove the fan. you have a automatic belt tensioner. look for small pulley to passenger side of fan. pulley will be attached tp leaver which is the tentioner. on the leaver in a 3/8 dive hole in it so you can attach a ratchet or braker bar in . once you in mount ratchet push or pull on ratchet to release tention hold back on tentioner and take belt off pay close attention to how the belt is routed.

Jul 13, 2012 | Cars & Trucks

1 Answer

Need serpentine belt routing diagram 1987 Chev Astro Van 6 cyl


If nobody here provides it for you (I don't have your van's manual), then visit the chevy dealership and ask a not-too-busy shop foreman or a parts dept. person for a little assistance. A quick look in a repair manual for your van may also have it. It must have got scraped off or disappeared from under your hood, on a little sticker?

Nov 12, 2011 | 1987 Chevrolet Astro Cargo

1 Answer

How do a put a serpentine belt on a chevy astro van


first look the bilt set up. then install bilton pullies push doun on bilt tentioner and slide bilt onteentioner pully

Jan 14, 2011 | Chevrolet Chevy Cars & Trucks

1 Answer

Need diagram for serpentine belt for 1988 chevy 2500 350 eng. no air


how do you route a serpentine belt for a 1988 chevrolet 350 ci with a ac. and airpump 2500 series truck

Dec 14, 2010 | Chevrolet 2500 Cars & Trucks

1 Answer

1need to know how to take the tention out of the pullies so I can reinstall the drivebelt and the ac belt


Your AC and Alternator should be attached to brackets that release the tension when you loosen the bolts. Once you've installed your belts use something, or have someone help you to hold each part up while you tighten them back in place.

Hope this helps!

Jun 25, 2010 | 2001 Chrysler 300M

2 Answers

Where is the fuse box located in a 1987 Chevy Astro


Under the dash on the drivers side near the parking brake

Apr 10, 2010 | 1987 Chevrolet Astro Cargo

1 Answer

Routing diagram for a Chevy G20 serpentine belt?


Okay, there are a few engines that come in this van, lucky there the same except,they come with or without ac or airpump, so i will give you all of them and you choose the right one.a613984.gif492790a.giffd1ae03.gif47b4a5f.gif

Mar 14, 2010 | 1994 Chevrolet G20

1 Answer

Need diagrams of 4 belt system 1987 chevy 350


back belt nearest the engine goes around the crankshaft pulley and the power steering pump
next belt out goes around crankshaft, power steering pump water pump and ac compressor
next belt goes around crankshaft water pump and alternator
last belt goes from water pump to smog pump

Feb 21, 2010 | 1987 Chevrolet R10

1 Answer

I need to replace the drivebelt on my 95 ford windstar. where is the tension pulling and how do I release it to install the belt?


The tention pulley is a small wheel located on a braket that looks as if it does nothing at all. It may have a square hole in the braket or in the pulley itself. There are certain tools used to release the tension and they are simply inserted into this square hole and pressure is applied to move the pulley( which is spring loaded) to releave the pressure from the belt. Its only purpose is to create tention on the belt.

Feb 16, 2010 | 1995 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...