Question about 1999 Ford Escort

1 Answer

Complete engine assembly, ford escort 1983, front wheel drive, 1.3 Lt

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 373 Answers

You can order a long block from some auto parts stores, or just google search for a 'long block 83 ford escort 1.3 liter, JASPER is a good example. plenty of websites out there that can help, shop around for best price

Posted on Feb 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the order of the cylinders in a ford escort 1975


used to build the engines on the assembly line ,1243 as i remember but it could be 1342 .Make sure that if clean the autolite carb out you dont loose thte little ball bearing and weight piece on top of it .

Apr 30, 2011 | 1983 Ford Escort Gt

1 Answer

The front wheels and steerting wheel of my 1994 ford escort shake when accelerating and braking.... could you tell me what the problem might be ?


Probably one or more bad motor or transmission mounts. You can brake torque the engine in reverse and drive, if the engine rocks violently in either step those mounts need replaced.

Apr 06, 2011 | 1994 Ford Escort

1 Answer

I need to know step by step on how to set the timing on my 2002 ford escourt zx2 and i cant find a repair manual anywhere... i would greatly appreciate the help Jamie


  1. Remove or disconnect the following:

  2. Negative battery cable Accessory drive belt and tensioner Timing belt cover Right front wheel Right inner splash shield Crankshaft pulley
  3. Align the timing marks.
    1. Removing Timing Belt
    1. Loosen the timing belt tensioner bolt (1).
    2. Use an 8mm Allen wrench, and turn the tensioner (2) counterclockwise 1 / 4 turn.
    3. Insert a 1 / 8 inch drill bit in the hole (3) to lock the belt tensioner in place.
    4. Remove the timing belt (4).

      To Install :

    5. Install the timing belt in a counterclockwise direction starting at the crankshaft.
    6. Remove the drill bit to unlock the timing belt tensioner.
    7. Rotate the crankshaft two complete turns and check that the timing marks align.
    8. Tighten the tensioner bolt to 15-22 ft. lbs. (20-30 Nm).
    9. Reinstall or connect the following:

      Crankshaft pulley. Tighten the bolt to 81-96 ft. lbs. (110-130 Nm). Right inner splash shield Right front wheel Timing belt cover Accessory drive belt and tensioner Negative battery cable
    10. Start the engine and check for proper operation
  • Aug 11, 2010 | 2002 Ford Escort

    1 Answer

    Engine problem 1999 Ford Escort 4 cyl Front


    Sounds like you make have a vacumn leak on one of the rubber vacumn lines that attach to the intake manifold. Check all of these lines and look for cracks, pinholes and lines that have colapsed.

    May 08, 2010 | 1999 Ford Escort

    1 Answer

    How do I replace a 1998 ford escort front brakes


    THIS IS FREE INFORMATION...FROM WF Pads Removal
    1. WARNING: Asbestos fiber dust may be present on brake and clutch assemblies and is hazardous to health if inhaled.

      Brake and clutch assemblies should be cleaned using a vacuum cleaner recommended for use with asbestos fibers such as brake/clutch/service vacuum. The bag must be labeled per osha instructions, sealed, and the trash hauler notified as to the bag's contents.

      If a vacuum suitable for asbestos is not available, cleaning should be done wet. If dust generation is still possible, technicians should wear government-approved toxic dust purifying respirators.

    1. Raise and support the vehicle.
    2.Remove the wheel and tire assembly.
    3.Remove the W-spring.

    b79833a.gif
    4.Remove the M-spring.

    d85663c.gif 5.Remove the disc brake caliper locating pins (2B296). b3aeaa2.gif 6.Remove the front disc brake pads and shims from the disc brake caliper (2B120).

    0bc00cf.gif 7.Compress the caliper piston completely into its BORE 1cfadfa.gif NOTE: Apply a thin layer of Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A Motorcraft WA-10 or equivalent meeting Ford specification ESE-M1C171-A to both sides of the perforated shim only.

    Mar 25, 2010 | 1998 Ford Escort

    1 Answer

    How to install wheel bearing hub assemble (front)1998 on a ford escort


    front or rear?

    Assuming rear, on the brake drum:

    Hub Removal
    1. If equipped, remove the brake drum (1126) ; refer to Section 206-02 . If equipped, remove the rear disc brake rotor (2C026) ; refer to Section 206-04 .
    1. Remove the wheel hub.
      1. Unstake the rear axle wheel hub retainer.
      1. Remove the rear axle wheel hub retainer and discard.
      1. Remove the wheel hub (1104).

    Nov 05, 2009 | 1998 Ford Escort

    1 Answer

    Fuel filter location for 94 ford escort lx


    on the fuel injection engines the fuel filter is located in one of 2 places 1, under and to the rear of the engine above the drive shafts or 2, under the car at the rear just forward of the rear suspension assembly

    Apr 25, 2009 | 1995 Ford Escort

    1 Answer

    Tranny drop


    make sure all bots etc are out, drive shafts diconnected support engine remove gearbox mount lower engine enough to slide gearbox out if all bolts are out and it still will not come apart you may need to just prise the bell hosing from the rear of the engine as it could well be just stuck

    Mar 01, 2009 | 1990 Ford Escort

    1 Answer

    Front wheel bearing


    Service and Repair
    1. Remove front hub/steering knuckle assembly from vehicle.
    2. Position front hub/steering knuckle assembly on a press and press front hub out of steering knuckle using a suitable removal tool.
    3. Remove E-clip from steering knuckle, then position steering knuckle onto a press.
    4. Using a suitable bearing remover, press bearing out of steering knuckle.
    5. Reverse procedure to install.

    Jul 17, 2008 | 1993 Ford Escort 4 Door

    Not finding what you are looking for?
    1999 Ford Escort Logo

    Related Topics:

    144 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    60769 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Fordexpert

    Level 3 Expert

    5331 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...