Question about 1999 Nissan Quest

3 Answers

HOW TO CHANGE REAR BRAKE LIGHTS 1999 QUEST?

TRYING TO CHANGE MY BACK BRAKE LIGHTS AT HOME . I CAN NOT GET THE COVERS OFF. I ALREDY UNSCREWED THE COVERS .

Posted by on

  • Anonymous Mar 20, 2009

    I can't take the brake light out of its housing. I unscrewed the 2 philips head screws. I also tried pulling it up, and side to side with no good results. I also tried a slim long screwdriver to try to pry the clamps out. I could really use some good advice for this problem

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I replaced my lights last week. After the 2 screws are removed, the unit is held in place with 2 rubber posts (this may not be the right term). Pull the whole unit away from the van by forcing it out or away from the back/cargo door towards the front sliding doors, they should pop-out. The bulbs housing is a simple twist and pullout.

GoodLuck,
DMunsellNC

Posted on Apr 26, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

After lifting the rear hatch there are two phillip screws that secures the light. Take those off and gently lift the light cover out of it's housing ( becareful not to break the clips ) by moving it side to sid ewhile pulling.

Posted on Mar 10, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 59 Answers

I don't know this van but many tail light assembly's have a couple of screws you remove then a couple of snap clips. So after you remove the screws you gently pry the assembly off with a slim pry tool.

Posted on Feb 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to get rear lens cover off to change rear brake light


i need to replace a broken back light lens on a 2000 quest

Sep 22, 2010 | 2008 Nissan Quest

2 Answers

I need to change the brake light but can't figure out how to get the cover off and it is not in the manual. Do you know how to get to the bulb to change it?


Most 3rd brake light covers are held on with 2 plastic screws located on the sides, or the cover is just a push fit, easily pried off with a thin blade such as a putty knife screw drivers sceatch it up badly

May 31, 2010 | 2005 Nissan Quest

1 Answer

How do I change the brake bulbs on 99 Nissan Quest


The whole assembly will pop out with a screwdriver (carefully). Then the bulbs can be reached. Just push the whole thing back into the slots when you are done.

Feb 17, 2010 | 1999 Nissan Quest

1 Answer

I HAVE PROBLEMS WITH STOP LIGHTS ,THEY DONT TURN ON


1) Unplug the Brake Light Bulbs and with a Voltmeter, check for voltage on both sides.
2) If you have voltage: change the bulbs and recheck operation.
3) If you do NOT have voltage: go under the dash on the drivers' side. Look up onto the arm of the Brake Pedal. There should be a switch behind the arm, On the switch should be a plunger. With a partner at the rear of the vehicle: Depress the plunger in, and have your partner check for Brake Lights.
4) If you now have Brake Lights: the plunger and/or switch can be adjusted. The Brake Arm when depressed, pushes-in the plunger activating the Brake Lights. Some Plungers can be unscrewed (counterclockwise) to shorten the gap to the Brake Arm,
5) If you still have NO Brake Lights: Twist the Switch/Plunger 1/4 turn, removing it off the support bracket. Unplug this Switch and again check for voltage.
6) If you have voltage: the Switch is bad and needs to be replaced.
7) If you still have NO voltage: Check the fuses.
Let me know if this helped, or if you have any additional information or questions. Feel free to contact me at FixYa.com!

Feb 15, 2010 | 1999 Mercedes-Benz M-Class

1 Answer

Brake lights dont work w/ headlights on


there is a short in the system more than likely in the headlight switch itself causing the problem. not a hard fix just remove the covers from around the column and unbolt the headlight switch from the column and bolt in the new one and see if this fixes your problem also check and make sure you dont have a broken ground at the rear of the vehicle for the rear lights, should be bolted to the frame black wire, generally on driver side.

Aug 28, 2009 | 1999 Jeep Grand Cherokee

1 Answer

1999 nissan quest rear brake shoes need changing


help is here:
http://autos.groups.yahoo.com/group/villagerquest/

Drum Removal
  1. Remove the rear wheel and the tire assembly. Refer to Section 204-04 .
  1. Retract the brake shoes and loosen the brake adjuster screw.
975565f.gif
  1. Remove the brake drum.
----------------------
May require big hammer to loosen drum from axle flange. Hit between the the lugs, not on them.

------------------------------------------------------------------------------
#10 is access plug to back off adjusting wheel.

f9f31b5.gif
Item Part Number Description 1 2261 Rear wheel cylinder 2 — Dust boot (part of 2128) 3 2197 Wheel cylinder piston (part of 2261) 4 — Cup (part of 2128) 5 2204 Wheel cylinder piston cup spring (part of 2128) 6 — Wheel cylinder housing (part of 2261) 7 — Brake shoe hold-down pin 8 — Access hole (part of 2212) 9 — Rear brake bleeder screw (part of 2261) 10 — Access hole plug 11 — Rear wheel cylinder bolt 12 2212 Rear brake backing plate 13 — Rear brake backing plate bolts 14 2N790 Parking brake lever clip 15 — Spring washer 16 — Secondary brake shoe and lining (part of 2200) 17 — Brake shoe hold-down spring (part of 2B514) 18 — Lower retracting spring (part of 2B514) 19 2A637 Parking brake lever 20 — Parking brake lever pin 21 2A177 Brake shoe adjusting lever 22 — Adjuster lever pin (part of 2A177) 23 — Primary brake shoe and lining (part of 2200) 24 — Upper retracting spring (part of 2B514) 25 2041 Brake adjuster screw

--------------
Shoes Removal

Take a picture and remember how each part goes and attaches
  1. Remove the brake drum, refer to Drum in this section.
  1. Remove the upper retracting spring.
  1. Remove the lower retracting spring.
  1. Remove the self-adjuster.
38bcaa0.gif
  1. Remove the hold-down springs.
  1. Remove the parking brake lever clip and the parking brake lever.

Apr 17, 2009 | 1999 Nissan Quest

1 Answer

Brakes?


change the rotors you most likly have a thickness variation causing the brakes to pulsate

Oct 22, 2008 | 1999 Nissan Quest

Not finding what you are looking for?
1999 Nissan Quest Logo

199 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...