Question about 2003 Jaguar X-Type

1 Answer

How do you bleed the left rear brake 03 Jaguar.

I changed the left rear caliper and pads and I can't bleed the left rear? Is there a trick to bleeding the left rear, or is there some special I need to do? The right rear is fine, the car won't stop properly when driving. What can I do?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 103 Answers

I would try vacum bleeding it....you can use a tool like a "mity-vac"

Posted on Feb 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bleeding 02 toyota sequoia


You have a helper pushing on the brake pedal when you open the bleeders? Is fluid coming out of the bleeders when you open them?

typically you will start at the right rear, then left rear, then right front, then left front. or work your way from the farthest bleeder to the nearest bleeder to the master cylinder. Make sure the reservoir does not go dry or you will have to start over.

It is possible that when you pushed the pedal to the floor the seals in the master when through some debris and where ruined.

Apr 11, 2013 | 2002 Toyota Sequoia

1 Answer

Bootscooters@my 1998 s10 blazer keeps wearing out pads on the left rear, after replacing both roaters and both sets of pads.


Sounds like u need to replace your brake caliper on that side. It's engaging but not totally disengaging causing it to wear so fast. Replace the caliper and brake pads and have your brake fluid flushed. At the end make sure they "bleed your brakes". then enjoy many happy miles on the road my friend. A good honest automotive repair shop will, bleed and flush the brake fluid for little to no cost. If your getting them to replace the caliper and pads.

Aug 14, 2011 | Chevrolet S 10 Cars & Trucks

1 Answer

2000 buick lesabre with abs-low brake pedal after changing all 4 rotors and pads. did not open the hydraulic system


When changing pads and you push the caliper in for the new pad you should open the bleed screws. , then close and re-assemble. press pedal and open bleed screw and let it drip a little . gravity bleed. Did you turn the read caliper piston in and then press it down? The rear piston must be aligned with the pad. Did you pump the parking brake to reset?

May 20, 2011 | 2000 Buick LeSabre

3 Answers

After putting on new calipers on both sides of my dodge ram 2005 1500 and bled brakes I have no brakes. What is the problem they worked fine until I did the caliper and brake


Did you bleed rear brakes also? Should do all 4 whenever bleeding brakes starting w/ right rear, left rear, right front then left front. Sounds like air in lines.

Mar 22, 2011 | 2005 Dodge Ram 1500

1 Answer

Is there a trick to bleed the brakes on a 1990 volvo 240 because there are three bleeder screws on each caliper and the bottom 2 dont have any air in them but the top ones on each side wont relese any...


Bleed in this order for non-ABS: Left Rear, Left Front Top, Right Front Top, Right Rear, Inner Right Bottom, Outer Right Bottom, Outer Left Bottom, Inner Left Bottom.

Bleed in this order for ABS: Left Rear, Right Rear, Left Front, Right Front.

Oct 17, 2010 | 1990 Volvo 240

1 Answer

I want to replace the rear disk pads on my a-6 Quattro 3.0; can I safely use one of those compressor kits from a parts place to compress the pistons, any tricks to share ?? and anything to worry about...


I have taken the brake caliper of the rear passenger side and renewed the seals in it i have also renewed the brake pads in that wheel i have tried to bleed it before renewing the pads in the outherside but when i open the bleed nipple and push the peddle down there is no braked fluid coming out i also renewed the nipple.When you take the brake pipe off the caliper ther is still no fluid coming out also there is no pressure on the pedal 1997 audi a4 1800

Jul 26, 2008 | 1998 Audi A4

1 Answer

Brake pad change


try to bleed first the master cylinder and then the calipers

Jun 16, 2008 | 2000 Jaguar S-Type

Not finding what you are looking for?
2003 Jaguar X-Type Logo

Related Topics:

272 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Raygin
Raygin

Level 2 Expert

322 Answers

yadayada
yadayada

Level 3 Expert

61168 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...