Question about 1992 Isuzu Pickup

1 Answer

Changing the head gasket... how many pounds of torque do is use.

How does the bolt pattern follow for tightening the head gasket down. And what do i set the torque wrench at. thanks alot -Eric

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Isuzu Master
  • 19,482 Answers

Posted by Ericandcrist on Feb 23, 2009

poor guy sold it.. after all its a stinkn isuzu

Posted on Feb 25, 2016

6 Suggested Answers

  • 2 Answers

SOURCE: what is the 98 isuzu rodeo head bolt torque

joyce, there are different specs for sohc and dohc engines. my advice is to get a Haynes manual from the auto parts store.

doug

Posted on Sep 01, 2008

c17hydro
  • 2984 Answers

SOURCE: cylinder head torque settings 1990 2.6L isuzu motor

From front to back is this:


7 3 1 5 9



8 4 2 6 10



First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.

Posted on Mar 21, 2009

  • 194 Answers

SOURCE: need cylinder head torque settings and tightening

This is not necessarily specific for your car but as a general rule of thumb, if you start in the middle of the head and work your way out, torque down to 30 ft/lb first and then a quarter of a turn on second pass. Specific instructions often come with a new head gasket.

Posted on Aug 04, 2009

stevenhurc
  • 450 Answers

SOURCE: torque settings for a holden rodeo 3.5 ra. Head

stage 1 = 29Nm(21 lb ft/3.0 kg-m)
final = 64Nm(47 lb ft/6.5kg-m)
do not reuse head bolts or apply any lubricant to the bolts. Do up bolts in following order for each head.
6 1 3 7
front
5 2 4 8

Posted on Dec 05, 2009

  • 365 Answers

SOURCE: do i need a torque wrench to replace my intake

you should use a torque wrench but if you tighten them by hand make sure that you pull them down reasonably tight and check them a few days later as they may need to be retightened

Posted on Jun 13, 2010

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

03 Dodge Intrepid intake manifold torque specs top & bottom is for 3.5 V6


Lower Intake:
  1. Use a skin coat of RTV silicone on both sides of the water passage ports (outer most holes) and put the new lower intake gaskets into place
  2. Hand tighten the 13mm head intake bolts and Torque the bolts , starting from the center and working your way out in a circular pattern
  3. Torque these bolts in a few small increments until they have reached 250 inch pounds of torque.
  4. Upper Intake Plenum:
  5. When installing the intake air plenum , be sure to catch the four center bolts and the two side bolts (stiffener brackets) before tightening , The center bolts should be torqued to 250 inch pounds .The fuel rail bolts should be torqued to 100 inch pounds

Jun 24, 2016 | 2003 Dodge Intrepid

1 Answer

Hi, we are re assembling my Toyota tazz 1.3 2001 engine, can I please have torque settings for everything


Head gasket Torque sequence
36 pounds then to 49 pounds then an additional 90 degrees. You should get new head bolts though because this style of bolt can stretch causing the head gasket to leak. See tightening pattern


26192507-aae5jkoeqllm4c5gsk2qfzg5-5-0.jpg

May 12, 2016 | Toyota Cars & Trucks

1 Answer

2007 yaris 1.5 Ing. What's the torque pressure on heads


PDF]Complete Cylinder Head Torque Specifications for Domestic ...

olybrake.com/pdf/fel_pro_torque_specs_guide.pdf
When you consider what can go wrong when even "minor" gaskets fail, ... and engine block, tightening the head bolts compresses the gasket slightly, allowing ...Missing: ing

How To Torque Cylinder Head Bolts - EricTheCarGuy ...

? 25:08
https://www.youtube.com/watch?v=5WHBskK_F3o
Aug 29, 2010 - Uploaded by EricTheCarGuy
How To Torque Cylinder Head Bolts - EricTheCarGuy http://www.ericthecarguy.com/ Well ... What's the reason for changing the torque pattern?Missing: yaris

CTA Tools 9295 Toyota Head Bolt Wrenches -Dou



Dec 30, 2015 | Cars & Trucks

2 Answers

I need the torque spec for the valve cover on a 06mercury malin


There is a torque spec for the cylinder head; I don't know of one for the cover.

Jul 14, 2015 | Cars & Trucks

2 Answers

2001 daewoo lanos dual overhead 1.6 liter head bolt torque and sequence


  1. Tighten cylinder head bolts to 25 N.m (18 ft. lbs.). Tighten bolts an additional 70 degrees plus 70 degrees plus 30 degrees using angular torque gauge .
2001-daewoo-lanos-dual-overhead-1-6-vrq3bch1e30nz1jlq5sn5nnt-4-0.gif

Oct 20, 2011 | 2000 Daewoo Lanos

1 Answer

Changing head gasket torken head down - settings


Here is a picture of torque pattern for a 2200 2.2L
Tighten the cylinder head bolts in 2-3 steps in the proper sequence. The final torque specification is 59-64 ft. lbs. (80-86 Nm).

chuckster57_18.gif

Jan 24, 2011 | 1992 Mazda B-Series

1 Answer

1994 4runner, six cyl. putting rebuilt heads on, toyota head gaskets, new head bolts "tvs 10.9". Torqued bolts in pattern to 33 foot pounds. another 1/4 turn in the pattern. and into my next and final 1/4...


REMOVE 3 BOLTS MAKE SURE YOU HAVE THE RIGHT THREADS.IF BOLTS LOOK OKAY.YOUR BOLTS HOLES HAS DEBRIS OR OIL AND ANTIFREEZE IN THEM.OR YOUR BOLT HOLES IS STRIPPED.YOU HAVE TO REMOVE HEAD TO FIX THE THREAD PROBLEM.IF YOU HAVE NOT MADE THE FINAL TORQUE TO CRUSH AND SEAL HEAD GASKET THE. HEAD GASKET PROBABLY ALRIGHT.YOU HAVE TO LOOSEN HEAD BOLTS IN SEQUENCE BACK OFF A LITTLE AT EACH BOLTS.IF HEAD GASKET LOOK DAMAGE AT BOLT HOLES REPLACE HEAD GASKET.

Nov 13, 2009 | Toyota 4Runner Cars & Trucks

2 Answers

What is the tension on cylinder head bolts for a jeep grand cherokee 307935 4 litre, 6 cylinder, 1999, petrol motor.


Coat threads of left hand front bolt with sealant: 1st - step; - 22 ft./lbs. 2nd - step; - 45 ft./lbs. 3rd - step, all bolts except L.H. front bolt; - 110 ft./lbs. 4th - step, L.H. front bolt; - 100 ft./lbs. fig100.png

Sep 05, 2009 | 1999 Jeep Grand Cherokee

2 Answers

Need the cylinder head torque settings on a toyota corolla 1990 model ae92 wiht a 4a-fc engine


Tighten in several passes to 44 foot pounds.

I just wanted to add. Since this is an aluminum cylinder head, I hope you loosened the head in the loosening torque pattern. The pattern opposite of the torque tightening pattern. If not, you stand the chance of warping the head.

Again, since it's an aluminum head, it needs to be checked for flatness. Most aluminum heads need to be surfaced before re-installing.

Tightening torque pattern is as follows:

1.The Drivers side of the engine is the Left side.
From the Front going towards the back; the bolts are numbered 10, 6, 1, 3, and 7.
From the Front going towards the back on the Passenger side; the bolts are numbered 8, 4, 2, 5, and 9.

The Exhaust and Intake Camshaft Bearing Cap bolts go to 9 foot pounds. Tighten gradually. One bolt to the other with so many foot pounds, work back, and forth up to 9lbs.

Camshaft Timing Pulley bolts go to 43 foot pounds. (In a tightening sequence, and gradually)

Jul 25, 2009 | 1990 Toyota Corolla

2 Answers

Head gasket torque specs


Here you go, I hope this is what you were looking for:

For 1987-94 models, the cylinder head bolts are tightened in 3 progressive steps. Tighten them in the proper sequence as follows:
Step 1: 50-55 ft. lbs. (68-75 Nm) Step 2: 60-65 ft. lbs. (81-88 Nm) Step 3: 70-85 ft. lbs. (95-115 Nm) Let me know if I can assist you with anything else.

Apr 30, 2009 | Ford F-150 Cars & Trucks

Not finding what you are looking for?
1992 Isuzu Pickup Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

63589 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...