Question about Ford F-350 Super Duty

1 Answer

Unhooking key switch dinger

I am trying to find out how to unhook the dinger that comes on when you put your key in the ignition switch in a 2002 F350 power strokeje

Posted by on

  • Anonymous Mar 16, 2009

    WHAT WIRE ISIT?

  • yadayada
    yadayada May 11, 2010

    it is part of a larger control module, u can't disconnect it, but u can make it think the key is out of the ignition buy disconnecting the signal wire to the module from the key cylinder.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 49 Answers

Look on fuse box or close to it is round or square.

Posted on Feb 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The dinger(the alert sound that goes off when your lights are still on or when your keys are in the ignition) and locks keep going off even when I turn the car off


It should be just fine, unless you have something inside the vehicle that requires use of battery ( something added not factory)

Apr 02, 2013 | 1996 Oldsmobile LSS

1 Answer

Door dinger stays on after the car is shut off we have to unhook the battery everytime we get out of the car any solutions on why and how to fix it.


It sounds like the door switch needs replacing. They are dealer only products but cant imaging it would be costly. In the mean time try to duct or gorilla tape to keep it from killing your battery & having to unhook battery every time you want to go somewhere. Good Luck & I hope this helps you out/

Jan 17, 2012 | 2000 Kia Sephia

1 Answer

WHEN DRIVING MY '97 CR-V CAME TO STOP PUT IT IN PARK BUT IT STAYED IN DRIVE HAD TO TURN IF OFF, KEY STUCK IN IGNITION HAD TO UNHOOK BATTERY, UNABLE TO GET IT OUT OF DRIVE


Could be the ignition switch. Honda issued a recall on 1997 CRV ignitions in 2002.
Go to www.ahm-ownerlink.com and under quick tasks, click on the Get Recall Information.

May 31, 2011 | 1997 Honda CR-V

1 Answer

WHERE IN THE IGNITION SWITCH LOCATED ?NOT THE KEY SWITCH !


Take the plastic cover off the steering column, it's a black rectangular piece just to the left and down from the key switch. It is held in there by 2 springs, push these two springs in and the ignition switch will fall down. Unhook the terminals that are hooked to it, and replace with a new one.

Mar 02, 2011 | 2002 Chevrolet TrailBlazer

1 Answer

Replaced fender silenoid and ignition switch under dash. Even after unhooking all terminals from starter, the positive cable from battery is bubbling hot. There is a faint clicking coming from under...


Tough one. First thing I would do is replace your cables, signal wire from ignition switch to solenoid included. Sounds like a short somewhere.

Dec 24, 2010 | 1991 Ford F350

1 Answer

Ignition turns off immediately after turning. wont hold in run is there an easy fix or bypass? 1991 mercury marquis


They get real sloppy the ignition switches on most older fords.....unhook your battery then put the key in the run position and on the bottom of the steering column there is a small hole that is acceess to the release pin for that ignition swich ..you need a small screwdriver of lung thin punch to push that in and your ignition switch just comes our .
Go to the local wreckers or dealer and get a replacemen ........Keep in mind the key will be different from before so make sure the used one comes with a key

Aug 18, 2010 | 1991 Mercury Grand Marquis

1 Answer

Change starter on 2002 tahoe now motor wont start


If you had battery unhooked and assuming that it is turning over try this Put your key in turn it on dont start wait 10 mins remove key wait 10 seconds repeat this a total of 3 times. If that dont work try a different key do the same thing. This relearns your key to the ignition it started with Gm cars and trucks from 1999 to to 2006. It is a big problem but there is no recall that I know of. If that dont work a dealer needs to probably replace and reprogram your ignition switch and keys

Dec 27, 2009 | 2002 Chevrolet Tahoe

1 Answer

I have a 87 ford f250 6.9 idi it terns over win i put the batter cabel on the batter


try unhooking the ignition switch wire from the solenoid, if it still turns over, the solenoid is bad.

Oct 28, 2009 | 1990 Ford F350

1 Answer

Unhooking key switch dinger


Look in the dash area, follow the sound for the dinger module and remove this instead of wires.

Mar 27, 2009 | 1995 Ford Windstar

1 Answer

TURN THE KEY AND NOTHING, UNHOOK BATTERY AND WAIT START RIGHT UP?


hi you have a problem with its immobilizer system when you take the battery lead off you are resetting its system then somethings over time is causing it to go down again either sort it out or dissconnect it yates210456

Oct 17, 2008 | 1998 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

219 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5610 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...