Question about 2001 Suzuki Swift

Open Question

Removal of brake drum on a suzuki wagon r

Rear wheels, wheel removed but not obvious how to remove the drum.
This refers to the wagon r which is not in the list of cars.

Posted by on

5 Suggested Answers

losflip
  • 94 Answers

SOURCE: Having difficulty removing rear brake drum on 2003 Suzuki Aerio.

Yes the phillips head screws have to be removed, on some models there are two more holes in the face of the drum to insert threaded bolts to remove the drum, simply thread the bolts in to remove the drum.

Posted on Nov 25, 2008

fknstart
  • 404 Answers

SOURCE: removal of rear brake drum 2002 ford escape

make sure handbrake is off take wheel off hit the drum with a mallet not steel,as it will brake,hit on outter diametter face of drum, try and rotate as you twist off

Posted on Jan 05, 2009

  • 3 Answers

SOURCE: REAR BRAKE DRUM WON,T COME OFF

is there one or two threaded holes near the center of the drum? buy one or two bolts that will fit these hole(s) and start cranking them down with your ratchet. Your brake drum shoud start pulling itself off as the bolt(s) push against the hub.

Posted on Apr 11, 2009

foskorider
  • 79 Answers

SOURCE: Need to remove then repair rear drum brakes

jack up one side at a time without the ebrake on as that will engage only the rear brakes remove lugs and have a good hammer handy and tap on the drum until it will pull off

Posted on May 19, 2009

  • 1 Answer

SOURCE: Rear Brakes drum 2004 Kia Rio

The rear drums are held on by a spindle nut. You first must remove the dust cap then unstake the nut and remove it. Behind that is a retaining washer and the outer bearing. The bearings can become a little stuck in which case a hammer can usually persuade them to loosen up.

Posted on May 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the rear wheel hub on a 2003 Kia sedona. All I can find is directions on front not back.


Wheel Bearings

Print
Adjustment

2002-05 Models
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:

    Rear wheel Brake drum Hub cover Cotter pin Lock nut cover
  3. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm).
Removal & Installation

2002-05 Models
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:

    Rear wheel Brake drum Hub cap Cotter pin Lock nut cover Lock nut Wheel bearing retainer washer and the outer wheel bearing Hub assembly Grease seal Inner wheel bearing
  3. Clean and inspect the wheel bearings and races for unusual wear or damage. Replace parts as necessary.
To install:
  1. Pack the wheel bearings with grease for assembly.
  2. Install or connect the following:

    Inner wheel bearing Grease seal Hub assembly Lock nut. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm). Lock nut cover Cotter pin Hub cap Brake drum Rear wheel

Apr 03, 2015 | 2003 Kia Sedona

1 Answer

Where the hell can I get a FREE PDF download for my Ford fusion 2 for the removal and replacement of the rear wheel bearings as well as the torque settings for the final nut after replacement.All the so...


Rear Suspension - Rear Wheel Bearing Fusion 2002.75 (06/2002-)

-Removal and Installation

Special Tool(s)

Installer, Differential Bearing
205-062

Installer, Input Shaft Seal
307-210 (17-041)


General Equipment
Soft faced hammerWooden block

Removal

CAUTION: The brake drum and hub assembly removal in this procedure is for installing a new wheel bearing, not for access to brake system components.

-All vehicles

Remove the dust cap.
Remove the wheel and tire.
For additional information, refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

-Vehicles with rear drum brakes
Release the parking brake.
Remove the brake drum and hub assembly.
Remove and discard the wheel hub retaining nut.


-Vehicles with rear disc brakes
Remove the brake disc.
For additional information, refer to in this section.

Remove the wheel hub.
Remove and discard the wheel hub retaining nut.


-All vehicles

Remove and discard the wheel speed sensor ring (brake disc shown).
Remove the circlip (brake disc shown).
Using the special tool, remove and discard the wheel bearing (brake disc shown).

-Installation

-All vehicles

CAUTION: Support the wheel hub assembly on the wheel mounting face and not on the wheel nut studs.

Using the special tool, install the new wheel bearing (brake disc shown).

Install the circlip (brake disc shown).

CAUTIONS:

Make sure the wheel speed sensor ring is not knocked, damaged and kept free from metal fragments.

Protect the face of the wheel speed sensor ring with a non-ferrous flat block to prevent damage.

Make sure the wheel hub or brake drum is adequately supported and do not allow it to rest on the wheel studs..

Make sure the wheel speed sensor ring is pressed on slowly and squarely until fully seated.

Do not exceed a maximum load of 10 kN.

Using the special tool, install a new wheel speed sensor ring (brake disc shown).

Vehicles with rear drum brakes

CAUTIONS:

Avoid impact on the wheel speed sensor ring.

Make sure the wheel speed sensor ring is clean.

Avoid any contact between the wheel speed sensor ring and a magnetic surface.

Rotate the wheel hub assembly 10 times counter-clockwise when tightening the wheel hub retaining nut to prevent damage to the wheel bearing.

NOTE: Install a new wheel hub retaining nut.

Install the brake drum and hub assembly.
Apply the parking brake.

-Vehicles with rear disc brakes


CAUTIONS:

Avoid impact on the wheel speed sensor ring.

Make sure the wheel speed sensor ring is clean.

Avoid any contact between the wheel speed sensor ring and a magnetic surface.

Rotate the wheel hub assembly 10 times counter-clockwise when tightening the wheel hub retaining nut to prevent damage to the wheel bearing.

NOTE: Install a new wheel hub retaining nut.

Install the wheel hub retaining nut.
Install the brake disc.
For additional information, refer to in this section.


-All vehicles
Install the wheel and tire.
For additional information, refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

NOTE: If the dust cap is damaged a new dust cap must be installed.

Using a soft faced hammer and a wooden block, install the dust cap.


There is no real torque settings for the rear wheels, except to say, do not over tighten or you will stretch the lugs and the will loosen over time.

May 28, 2011 | Ford Fusion Cars & Trucks

1 Answer

How do I get rear brake drum off?


You should jack up securely the rear end, and then remove the lugnuts to the wheels and remove the wheel.

Then, you may need a heavy hammer to tap on the 9 o'clock and 3 o'clock positions of the rear brake drum to loosen it up.

---
Here are instructions from Chilton/Haynes manual:

Drum Brakes Brake Drums Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Raise the vehicle.
  3. Remove or disconnect the following:
    • Rear tire and wheel assembly
    • Brake drum retaining clips (if equipped).
    • Brake drum.
NOTE: If the drum does not come off, further brake clearance can be obtained by backing off the brake automatic adjuster screw. Remove the rubber plug from the top of brake support plate. Rotate the automatic adjuster screw in an upward motion, using a screwdriver.
To Install:
  1. Install or connect the following:
    • Rear brake drum onto the hub assembly
    • Wheels
  2. Adjust the brakes as necessary
  3. Road test vehicle to check brake operation.
prev.gif next.gif

Feb 15, 2011 | 2001 Dodge Neon

1 Answer

How do i remove the rear drums on a 1998 ford escort wagon


  1. Raise and support the vehicle;
  2. Remove the wheel and tire assembly.
    1. Remove the lug nuts.
    1. Remove the wheel and tire assembly.
    2. Remove the brake drum.
      1. Remove the screws.
      1. Remove the brake drum.
      2. ce6f593.gif
                6d9298e.gif

                Mar 16, 2010 | 1998 Ford Escort

                2 Answers

                How to replace rear wheel bearings


                don't have topaz. maybe escort will help guide you.

                Section 04-02: Suspension and Wheel Hubs, Rear 1996 Escort, Tracer Workshop Manual
                REMOVAL AND INSTALLATION Wheel Bearing and Hub Assembly NOTE: Wheel bearings are not serviceable and should therefore be replaced as an assembly with the wheel hub (1104).

                Removal
                1. Raise and support the vehicle.
                1. Remove the wheel and tire assembly.
                1. Remove the hub grease cap (1131) from the wheel hub.
                1. If equipped with disc brakes, remove the rear disc brake caliper (2552) and rear disc brake rotor (2C026). Refer to Section 06-04 for the removal procedure.
                1. If equipped with drum brakes, remove the two brake drum screws and the brake drum (1126).
                1. Unstake the rear axle wheel hub retainer (4B477) securing the wheel hub to the rear wheel spindle (4A013). Remove and discard the rear axle wheel hub retainer.
                2. Remove the wheel hub from the rear wheel spindle.

                Feb 06, 2010 | 1990 Mercury Topaz

                2 Answers

                How do you remove the rear brake drum?


                Before you begin make sure your emergency brake is off.

                1. Jack up the car and remove rear tires.
                2. With a 13mm socket and ratchet remove the 4 bolts that are on the back of the hub assembly. (You will need an extension and a universal joint adapter)
                3. Pull the drum off and the spindle will come off with it, giving you access to the shoes, wheel cylinder, hold down hardware, etc... (you may need to adjust your brake shoes so the drum will slide off easier.)

                Do not undo the nut in the middle of the drum (under the dust cap) unless you absolutely need to turn the drum or replace the drum as the threads on the spindle are known to strip very easily. Should you need to take it off the socket for the spindle nut is a 30mm.

                Jan 05, 2010 | 2001 Ford Focus

                1 Answer

                How do i remove the rear brake drums from a suzuki swift


                Hi there,

                1) With the vehicle jacked up and supported with axle stands, remove the rear wheels.
                2) Using an old, thin, flat tip screwdriver and a hammer, remove the dust cap from the brake drum.
                3) Using a 1/8" punch and hammer, tap out the lock nut indentation.
                4) Using a 30mm, 1/2" drive socket and ratchet, unscrew the lock nut from the axle shaft.
                5) Remove the flat washer from the axle shaft.
                6) Ensure the hand brake is not applied.
                7) Using a soft faced hammer, strike the outside edge of the drum repeatedly and all around while at the same time applying a pulling force on the drum. (This is best accomplished using two people and could take several minutes.) Be persistent!
                8) Once the drum has been removed, tap or press out the wheel bearing from the inside out.
                9) Clean and re-pack the wheel bearing with grease.

                Good Luck!!

                Thanks

                Nov 18, 2009 | 2006 Suzuki Swift

                1 Answer

                How to install wheel bearing hub assemble (front)1998 on a ford escort


                front or rear?

                Assuming rear, on the brake drum:

                Hub Removal
                1. If equipped, remove the brake drum (1126) ; refer to Section 206-02 . If equipped, remove the rear disc brake rotor (2C026) ; refer to Section 206-04 .
                1. Remove the wheel hub.
                  1. Unstake the rear axle wheel hub retainer.
                  1. Remove the rear axle wheel hub retainer and discard.
                  1. Remove the wheel hub (1104).

                Nov 05, 2009 | 1998 Ford Escort

                1 Answer

                Is there a trick to removing rear brake drums on a 2004 corolla besides releasing the parking brake and loosening the adjuster star wheel?


                The only trick is banging it off. Drums are known to be "frozen" on or stuck. Honestly, the only way to get them off when they are stuck is to carefully hammer it off. Below is what is required to remove and replace the drum....and a picture of your system:

                Removal & Installation
                1. Before servicing the vehicle, refer to the Precautions section.
                2. Remove the wheels.
                3. Remove the brake drum from the axle hub.
                To install:
                1. Install the brake drum.
                2. Install the rear wheels, tighten the wheel lug nuts.
                b936120.gif

                Oct 29, 2009 | 2004 Toyota Corolla

                1 Answer

                1999 nissan quest rear brake shoes need changing


                help is here:
                http://autos.groups.yahoo.com/group/villagerquest/

                Drum Removal
                1. Remove the rear wheel and the tire assembly. Refer to Section 204-04 .
                1. Retract the brake shoes and loosen the brake adjuster screw.
                975565f.gif
                1. Remove the brake drum.
                ----------------------
                May require big hammer to loosen drum from axle flange. Hit between the the lugs, not on them.

                ------------------------------------------------------------------------------
                #10 is access plug to back off adjusting wheel.

                f9f31b5.gif
                Item Part Number Description 1 2261 Rear wheel cylinder 2 — Dust boot (part of 2128) 3 2197 Wheel cylinder piston (part of 2261) 4 — Cup (part of 2128) 5 2204 Wheel cylinder piston cup spring (part of 2128) 6 — Wheel cylinder housing (part of 2261) 7 — Brake shoe hold-down pin 8 — Access hole (part of 2212) 9 — Rear brake bleeder screw (part of 2261) 10 — Access hole plug 11 — Rear wheel cylinder bolt 12 2212 Rear brake backing plate 13 — Rear brake backing plate bolts 14 2N790 Parking brake lever clip 15 — Spring washer 16 — Secondary brake shoe and lining (part of 2200) 17 — Brake shoe hold-down spring (part of 2B514) 18 — Lower retracting spring (part of 2B514) 19 2A637 Parking brake lever 20 — Parking brake lever pin 21 2A177 Brake shoe adjusting lever 22 — Adjuster lever pin (part of 2A177) 23 — Primary brake shoe and lining (part of 2200) 24 — Upper retracting spring (part of 2B514) 25 2041 Brake adjuster screw

                --------------
                Shoes Removal

                Take a picture and remember how each part goes and attaches
                1. Remove the brake drum, refer to Drum in this section.
                1. Remove the upper retracting spring.
                1. Remove the lower retracting spring.
                1. Remove the self-adjuster.
                38bcaa0.gif
                1. Remove the hold-down springs.
                1. Remove the parking brake lever clip and the parking brake lever.

                Apr 17, 2009 | 1999 Nissan Quest

                Not finding what you are looking for?
                2001 Suzuki Swift Logo

                Related Topics:

                972 people viewed this question

                Ask a Question

                Usually answered in minutes!

                Top Suzuki Experts

                yadayada
                yadayada

                Level 3 Expert

                70346 Answers

                Colin Stickland
                Colin Stickland

                Level 3 Expert

                22041 Answers

                Boyet Soriano
                Boyet Soriano

                Level 2 Expert

                293 Answers

                Are you a Suzuki Expert? Answer questions, earn points and help others

                Answer questions

                Manuals & User Guides

                Loading...