Question about Dodge Sprinter

1 Answer

Looking for used rear bench seat for two for my 2005 sprinter, any ideas??

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

Your local junk/recycling/wrecking yard is your best bet.

Posted on Feb 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove middle row bench seat from a 2005 dodge caravan


Hi Amy, I'm AL the owner of Big As Auto Repair.
I look forward to helping you with your problem!

Amy, the middle bench seat is held in with four mounting bolts that must be removed from the legs of the seat. If you should need further assistance click here:
Auto Repair

Feb 27, 2015 | 2005 Dodge Caravan

1 Answer

How can a 2005 Toyota Avalon front passenger power seat be adjusted to lie flatter than it does now as the rear bench seat just slightly prevents it from doing so?


you will have to remove the seat ,battery disconnect of course as dont want the airbag light on,Now work out how mush you need it foreward then redrill the mountings and fit nuts and bolts to hold it as no doubt the existing fittings are capulated nuts in the floor pan .

Nov 02, 2014 | 2005 Toyota Avalon

1 Answer

Remove rear bench seat


I don't know about your exact make, but every bench rear seat bottom I ever messed with removed as follows:

Get your fingers under the bottom of the seat cushion, and give a sharp tug upwards.
It should be held in by spring clips, which will release with the upward tug.
With the front of the seat cushion slightly raised (so the spring clips can clear the brackets), it should then pull straight forward and out.

To re-install, push the cushion back under the seat back (with the front slightly raised), and with both hands, give a sharp push downwards to latch the spring clips.

Apr 24, 2014 | 1998 Nissan Pathfinder

1 Answer

How do I remove the rear bench seat on a Galant 2010 to install seat covers? Thanks


push back firmly at front of seat at bottomlocating clip released with upward preasure

Nov 14, 2012 | 2010 Mitsubishi Galant

1 Answer

Cant get the rear bench in


The front bottom connections goes in first. You have to lift the back of the bench up and slide the u-shaped connections under the rods. Once there in, then lower the back of the bench. The back has latches that should spring open and around the rods in the floor opening. You should be able to actually drop the back of the bench and they should "seat", however it is better to place the back of the bench on top of the rods, and using the lever located on the bottom of the bench - open the latches; causing the latches to grab the rod.
Let me know if this helped, or if you have any additional information, problems, or questions. Feel free to contact me at FixYa.com!

Jan 25, 2010 | 2005 Dodge Grand Caravan

1 Answer

How to remove the back seat from my 1998 Mercury Villager


it is not designed to be removed. It is designed to slide back and forth as needed.

Section 01-10: Seats and Tracks 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Seat, Rear Bench
Removal
  1. Remove the center seat(s) if equipped. Refer to the procedure in this section.
  1. Slide the bench seat forward to the center row seating position.
  1. Use a flat-blade screwdriver to remove the cover caps from the front of the rear seat cushion latch cover.




  1. Remove the two rear seat bolts from the front of the rear seat cushion latch cover.




  1. Lift the rear seat cushion floor cover on the back of the rear bench seat and remove the two inboard rear seat bolts and the two outboard rear seat bolts.




  1. Remove the bench seat from the vehicle through the body side door opening.

Apr 30, 2009 | 1998 Mercury Villager

1 Answer

2005 Ford Taurus Trunk jammed (kid's baseball bag), won't open with key or electronic unlock. Rear seat does not have trunk access. Can I remove seat back.


If it is a bench seat, most lower sections unbolt at the base of the front of the seat (near the foot well) then pull out. Once the lower section is out, the bolts to the upper section will be visable - undo those and the seats should lift up and out.

Apr 02, 2009 | 2005 Ford Taurus

2 Answers

I want to make my 1999 Mercury Villager Sport into a cargo loader, with just the front seats kept and the rest of the back empty. How do I remove the other 3 seats? So far, I can't get any of them to budge...


the middle seats come out easily. There are 2 handles you have to lift up on each of the bucket seats, they are in the front of the seat down by the seat tracks. After you lift them, tilt the seat upward in the front and rotate them backward. Then lift out of the hooks. Each seat is held down by 4 hoks.

The 3rd row seat is not designed to come out xcept by a technician. It does slide forward all the way up to the front seat. It has a sliding seat track.
First, lift the T handle under the seat cushion on the left front side of the seat. This will allow you to lift the seat bottom up all the way to lcok in the full up position.
Then, lift the lever on the same side of the seat and slide the seat forward. It will stop in 4 places.
Rear -Rear
6 inches forward of that.
another two ft to the second row seating position
full frward against the front seats.

Pleae rate as fixya if this helps.

c4253aa.gif Seat —Third Row Bench Removal
sxv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Removal of the third row bench seat requires more than one technician.
  1. Remove the second row seats. For additional information, refer to Seat—Second Row .
  1. Remove the floor mats.
  1. Lock the seat cushion in the upright position.
    1. Lift the handle to release the cushion.
    1. Lock the seat cushion in the upright position.
0235766.gif
  1. Move the third row bench seat to the second row position.
    • Lift the seat track release handle.
  1. Remove the two bolt covers.
  1. Remove the two seat track front bolts.
  1. Remove the four seat track rear bolts.
    1. Position the rear seat cushion floor cover aside.
    1. Remove the four seat track rear bolts.
  1. Remove the third row bench seat.

Mar 02, 2009 | 1997 Mercury Villager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...