Question about 2000 Dodge Durango

Open Question

Engine light is on

Fault Codes: P0320/P0725? What do I need to replace?

Posted by on

  • msmiley816 Feb 25, 2009

    Thank U........it was the cam shaft positioning sensor!

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Had 3 codes pop up for a 2008 nissan altima 2.5s


Fault codes rarely cause any drivability related symptoms.
P0740 NISSAN - Torque Converter Clutch Solenoid Circuit Fault
Possible causes
  • Low transmission fluid level
  • Dirty transmission fluid
  • Faulty torque converter clutch solenoid valve
  • Torque converter clutch solenoid valve harness is open or shorted
  • Torque converter clutch solenoid valve circuit poor electrical connection

  • P0826 means there is an issue with a circuit for the up and down switch, usually due to a disabled manual shifter or TCM placed in Limo-in mode.
  • The presence of a stored code P0725 means that the powertrain control module (PCM) has detected a circuit malfunction with the engine speed sensor input signal. The engine speed input sensor is sometimes called the transmission input speed sensor and the input speed sensor. This type of code may be caused by a mechanical problem or an electrical problem

Mar 30, 2018 | Nissan Cars & Trucks

1 Answer

Engine code PO725


They are vehicle specific in most cases. Google

Make error code P0725

and that is a zero, not letter O for Oscar.

Looks like

Definition of error code P0725 - Engine Speed input Circuit Malfunction. Read emissions expert information and diagnostics for fault code P0725.


Google

May 13, 2017 | Cars & Trucks

1 Answer

Engine light on with code P0725


P0725 JEEP Description The Engine Control Module (ECM) monitors the engine speed through the Crankshaft Position (CKP) sensor with the engine running, and send signal to the Transmission Control Module (TCM).
The code is set when the TCM does not get an engine speed signal from the ECM.
Could be a problem with either computer, the link between the two, or the crank sensor.

Read more: http://engine-codes.com/p0725_jeep.html#ixzz21kbHJXdi

Jul 25, 2012 | 1999 Jeep Grand Cherokee

1 Answer

P0725 code


P0725 JEEP Description The Engine Control Module (ECM) monitors the engine speed through the Crankshaft Position (CKP) sensor with the engine running, and send signal to the Transmission Control Module (TCM). Could be a faulty crank sensor or wiring problem.

Read more: http://engine-codes.com/p0725_jeep.html#ixzz21gJmt93c

Jul 25, 2012 | 2002 Jeep Grand Cherokee

2 Answers

2005 nissan almera,1.5letre.. fault code po725


P0725 NISSAN - Engine Speed Signal

The P0725 Codes is triggered when TCM does not receive the engine speed signal from ECM.

The Engine Control Module (ECM) monitors the engine speed through the Crankshaft Position (CKP) sensor with the engine running, and send signal to the Transmission Control Module (TCM).

Symptoms:
- Engine Light ON (or Service Engine Soon Warning Light)

Possible causes:
- Open or shorted CKP sensor circuit condition
- Poor CKP sensor electrical connection
- Check communication error between the ECM and TCM
- Failed CKP Sensor

Possible solution:
Very common problem with Nissan vehicles, usually replacing the Crankshaft Position sensor takes care of the problem.

Keep us updated.

Feb 12, 2011 | 2005 Nissan Altima

2 Answers

2002 Dodge Durango 4.7L V8 Check Engine Codes


1st try and search for a vaccum leak, due to the fact that these vehicles have had some bad problems with the length of wires and hoses, if there is a vaccum leak in the vehicle somewhere that will trigger other malfunctions in your vehicle. Using a can of starting fluid or Brake cleaner spray lightly spray around our engine til you hear the motor rev-up and the spot you have sprayed will determine where your vaccum leak will be. And then check under your distributor cap for any moisture be sure to take a rag and wipe and residue off. Also check the firing order on your distributor.

Oct 28, 2009 | Dodge Cars & Trucks

1 Answer

Engine light came on after hard **** going up hill. Brought car to the dealer and they said nothing is wrong but these codes came up and now I'm wanting to know what these codes are


P1243 - Inquiry Response Error - try reading codes again.
P0725 - Engine Speed Circuit Sensor Malfunction. - VSS or wiring bad.
P0705 - Transmission Range Sensor Circuit malfunction (PRNDL Input) - Sensor or wiring bad.


Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

May 21, 2009 | 2008 Mitsubishi Lancer

Not finding what you are looking for?
2000 Dodge Durango Logo

Related Topics:

935 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...