Question about 2005 Ford Fusion

1 Answer

Clutch does not release

Replaced new clutch on mondeo does not engage gears. only when switched off and when you start her up with the clucth pedel deprssed it moves forward.ABS AND ESP LIGHT STAYS ON.enough brake fluid in brake master cilinder.bled the clutch but still no joy.


Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 76 Answers

Did you check your pedal freeplay check your adjustment you need to have not more thant 1 inch freeplay on the clutch pedal what it does is when you did not adjusted right it cannot release your release bearing also check your linkage aite..

Posted on Feb 23, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Car has difficulty going in gear even if pedel is fully down

The clutch is not fully disengaging. Adjust the clutch cable to obtain a 1/2 inch of free play at the top of pedal stroke. If clutch adjustment is not correct, damage to synchronizers or clutch release bearing will occur. Your clutch should begin to engage about an inch off the floor when releasing the clutch pedal.

May 25, 2017 | Cars & Trucks

1 Answer

Hard to press clucth /hiace 2014 .while to engage hard to press clutch

check the clutch operation if it is hydraulic--press the pedal and see if the slave cylinder movers the throw out arm
It suggests a problem with the clutch master cylinder or a failed hose in the system that blocks off when the pressure is applied
hard to select the gears indicates that the pressure plate is not releasing
if it is a cable operation then replace the cable assembly as it is jamming up inside.

Aug 09, 2015 | Cars & Trucks

1 Answer

2007 kia cerato starter keeps engaging ever time you put the clucth in. Runs well but every time you change gears it engages the starter and when ignition is on put the clutch in and the car starts without...

When you push the clutch in ther must be two wires
pinching together, put the vehicle on a lift, with someone
inside it, have them push the clutch. While you or someone inspects for that.

Jan 20, 2014 | Cars & Trucks

2 Answers

2004 Dodge Durango Clutch fan issue, clutch fan disengages after 1-2 minutes after cold startup then engages everytime you come to a stop and start again, temp is just below halfway, I have already...

I just replaced my 2004 durango fan clutch and the new fan clutch will not disengage. The fan keeps runnning very loud i have replaced the new one already still doing the samething. Do i have a bad clutch or do i need to have the vehicle idle looked at

Jul 12, 2010 | 2004 Dodge Durango

1 Answer

My clutch slipps whit i hit 3000rpms in all gears .. do i need a new clutch

Ive always checked the cluth by putting it in like 3rd gear and giving it a little gas before you release clucth pedal should almost want to stall but if it whinds up then you probably need clutch.

Feb 04, 2010 | 1995 Volkswagen Jetta

2 Answers

Crossfire clutch feels like it sticking when switching gears what can i buy to make easier transition

"IF" you can pull the boot around the clutch release lever back enough. to shine a small flash light into the hole, Have someone shoot some P.B.Blaster(available at most hardware stores) "behind" the throw-out bearing and onto the splined shaft behind that. Avoid getting any spray on the clutch disk or the pressure plate work it back and forth. It might take a couple tries, but this should work.

Aug 17, 2009 | 2005 Chrysler Crossfire

2 Answers

2003 Tiburon GT 6spd won't go into gear occassionally

Take it to another mechanic,Also check to see if it may be covered by a recall

Jul 22, 2009 | 2003 Hyundai Tiburon

2 Answers

Clutch is loose and the gears are hard to shift.

when you say clucth is loose you probably mean that you have a lot of free play on the pedal..?

is it hydraulic?

if it is you'll have to bleed the clutch. if it isn't you'll have to adjust the clucth linkage.....

Apr 29, 2009 | 1988 Toyota MR2

Not finding what you are looking for?
2005 Ford Fusion Logo

549 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers


Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides