Question about 2005 Jeep Grand Cherokee

1 Answer

Replace Tailight Bulb. Brake/Running

I am having a hard time removing the tailight len cover. Reason There is one screw, that in the len and it is hard to get to.

Posted by on

  • yadayada
    yadayada May 11, 2010

    what is it u need from us??

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 156 Answers

Did you remove the rear access cover in the rear inside quarter panel?

Posted on Feb 23, 2009

  • Zachary Kloefkorn Feb 24, 2009

    oops...pressed the solution key not the more info one. Sorry bout that. Where is the screw located at? in between which pieces? there might be a special screwdriver that you can buy to get it out.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove rear right hand tailight to change bulb on 2004 Prado?


few both on the outer housing. if not then peel the panel off at the back and twist the bulb out

Jul 02, 2014 | Toyota Land Cruiser Cars & Trucks

1 Answer

Brake light is out how do i fix it?


the brake light bulb is a 2357 or 2357 LL (nearly the same) it's just a brighter 1157 and they'll fit too except they may not trigger a light out moniter correctly. in the trunk there's trim carpet covering the inside of the tailight's in there there's a snap on cover removing the cover the bulbs for the whole tailight are in their places as they fit into the back of the light, bad bulbs many times turn black or have a black spot on them. pick out the bad blub and pust it into it's baseand turn it to the left a little and then pull it out. It can have grease on it and that's OK. I reconmend to hold the bulb with a towell or other holder as the bulb can break and cut you. Install the new bulb with a towell as the little oil in your skin will deposit on the lens of the bulb holding the het into the bulb as it's on and it gets even hotter than it might otherwise and burn out too soon.

Sep 05, 2010 | 2008 Hyundai Accent

1 Answer

Replacing 92 Explorer right rear signal bulb


laurbeee,

As I have just seen this post I may be late in answering.

1. Open the hatch and look for the two screws on top of the tailight.
2. Take these out with a No.3 Phillips head screwdriver.
3. Pull on the tailight gently outward as the plastic inserts are what holds the lens in the body.
4. Locate the lamp for replacement and twist the lamp socket out of the lens.
5. Replace the bulb with the new one making sure to leave it clean of any oils from your hands. Twist the socket back into the lens.
6. Reasemble the lens back into the body and replace screws.


JTRadiojunkie

May 20, 2010 | 1992 Ford Explorer

1 Answer

Replace rear turn signal light


open trunk, remove screws that hold tailight in, twist out bulb holder, take out bad bulb, reinsert buld holer, replace tailight, replace screws, close trunk...YOUR DONE.

Nov 08, 2009 | 2000 Chevrolet Cavalier

3 Answers

How do I replace the bulb for the brake light..I have the bulb, but just need to know what to do to replace it.


If it's one of the lower ones... go in through the trunk, look to see if carpeting or a cover needs to be removed, or peeled back, usually the sockets twists (turns) to be removed, then the bulb will be exposed. An 1157 bulb needs to be pushed in slightly and turned to remove, (Counter clockwise) A 3157 bulb pulles straight out. Also note that some vehicles still need the exterior lens to be taken off, but I do believe yours is sealed!

Jun 29, 2009 | 1995 Chevrolet Lumina

1 Answer

Replace turn signal bulb on a 2000 monte carlo


inside your trunk you must pull back carpet exposing bolts holding tailight in. remove those bolts and pull tailight out. you can then remove sockets by turning counter clockwise. replace appropriate bulb

Jun 21, 2009 | 2000 Chevrolet Monte Carlo

1 Answer

Replace tailight


I just looked at a Prius in my shop; there is a small plastic removable panel (approx 3" x 4") inside the rear compartment, facing the taillamps...lift the panel off, and you now have access to the bulb sockets.

Sep 29, 2008 | 2004 Toyota Prius

1 Answer

Changing tailight bulb


First open the rear hatch. Look just inside the door next to the rear lens assembly. There should be 2 screws that need to be removed. This should loosen up the assembly. Next gently pull the assembly back and out to you.Do not pull to hard or to far, you are still connected with wire. Next, squeeze the retainer and twist the bulb assembly ccw. You are there. Reverse it to put it back. Good luck.

Aug 26, 2008 | 2006 Mercury Mountaineer

Not finding what you are looking for?
2005 Jeep Grand Cherokee Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...