Question about 1998 Jeep Grand Cherokee

1 Answer

Cant find free repair info

I can not find free repair info or manual for a 98 jeep grand cherokee specifically steering and front axle and axle shafts

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

If there is library near you there you can get all of the information you need on your car there.

Posted on Feb 23, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace Front Wheel Hub Bearing 2002 Jeep Grand Cherokee 2 wheel drive


Removal
  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake caliper, caliper anchor, rotor and ABS wheel speed sensor.
  4. Remove the cotter pin, nut retainer and axle hub nut.
  5. Remove the hub/bearing mounting bolts from the back of the steering knuckle. Remove hub/bearing from the steering knuckle and off the axle shaft.
Installation
  1. Install the hub/bearing to the knuckle.
  2. Install the hub/bearing-to-knuckle bolts and tighten to specification.
  3. Install the hub washer and nut. Tighten the hub nut to specification. Install the nut retainer and a new cotter pin.
  4. Install the brake rotor, caliper anchor, caliper and ABS wheel speed sensor.
  5. Install the wheel and tire assembly.
  6. Remove the support and lower the vehicle.

Apr 22, 2012 | 2002 Jeep Grand Cherokee

1 Answer

Replace left front axle seal


First you'll have to remove the axle shaft, and here's detailed directions so use whatever info you need. First you'll need to jack up your vehicle place your jack just behind the front lower control arm mount. Take off your tire/wheel, remove the cotter pin and the axle nut retainer, remove the 2 caliper mounting bolts, move the caliper out of the way and support it so it doesn't just hang by the brake hose. Now, slide your rotor off, next you'll need to remove the axle nut and at 180ft lbs of torque you'll need a breaker bar or a heavy duty impact. The nut should be a 36mm if I remember correctly. Remove the bolts holding hub to steering knuckle, remove hub now you can tap it with a hammer to help loosen it from splines on axle shaft. take off the dust cover, pull the axle shaft out now, take out your bad oil seal, grease splines, then install new seal, carefully reinstall axle shaft to avoid damaging the seal, reverse steps and you're good to go. Good luck with your repair

Jan 29, 2011 | 1995 Jeep Grand Cherokee

2 Answers

Front drive shaft on Jeep Grand Cherokee


yes but make sure you don't in gauge the front axle

May 19, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Need rubber boots on front axle


2000 Jeep Grand Cherokee with 4.0L or 4.7L same part.

Constant Velocity (CV) joint boot kit front axle shaft left or right outer part # 686115 this is a NAPA part #.

Jan 23, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Creaking sound while turning steering wheel


i'll bet this is a front wheel drive or four wheel drive. when the front wheels are tied to the drive train. the front axle shafts bearings can go kaput. jack up the vehicle and turn the steering wheel all the way to one side and spin one tire at a time by hand. you are bound to hear snaping and cracking coming from the axle shafts.

Dec 12, 2009 | 2000 Jeep Grand Cherokee

1 Answer

In a crash the frnt AXLE was bent, and i want to


Yes. You can get it for about $60-$75

I suggest going to autozone.com and register for free. Then you will have a full free online repair manual. Everything you could need for this vehicle with details, how-to's and much more. And you can order guranteed parts from there site.

Aug 03, 2009 | 1999 Jeep Grand Cherokee

1 Answer

U-joint replacement


Yes, but the cost of the u-joints/cv-joints (both ends) plus the labor involved in swapping out the u-joints, make a good argument for just replacing the half shaft as a unit. It's a lot quicker and cleaner.

Feb 25, 2009 | 1998 Jeep Grand Cherokee

1 Answer

Poping noise when moving 98' jeep grand cherokee


most likely due to front cv axles or front driveshaft being worn

Jan 09, 2009 | 1998 Jeep Grand Cherokee

2 Answers

98 jeep grand cherokee all time 4 wheel drive


i believe your talking about the slip joint dealer should have parts

Oct 24, 2008 | 1998 Jeep Grand Cherokee

Not finding what you are looking for?
1998 Jeep Grand Cherokee Logo

Related Topics:

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...