Question about 2007 Ford Fusion I4 SEL Sedan

6 Answers

Key stuck in ignition 2007 Ford Fusion - 2007 Ford Fusion I4 SEL Sedan

Posted by on

6 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I read other forums and found out if you remove the ring around the shifter button it releases the key. sometimes this gets stuck and the car thinks it is still in gear so it will not allow the key to release. this worked when it happen to me!

Posted on Mar 10, 2009

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Pull the beauty ring out from the shift knob the key should come right out its the circled ring on the shift knob jamming it up because the plastic tab is broken
Ford fusion v6

Posted on Apr 28, 2012

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

It's the ring on the shifter. It keeps the car from going into park so the key cannot be removed. Pull the ring up (whatever you do - don't push it down) and then the shifter will go into park and the key will come out. Don't leave the key in there and use another key to lock it because the car is not in park and could roll. Works for a long time by just pulling that ring up but eventually it has to be replaced.

Posted on Jun 20, 2011

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

Check on the steering column to see if there is a button to push and also make sure the car is in park all of the way.

Posted on Feb 23, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My key will not go thru all the way into the cylinder. It goes in have way. I have problems removing the ignition cylinder. Ford fusion 07

Posted on Sep 04, 2011

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had the same problem with my 2006 Fusion. What I did was install a new car battery.
For some reason my battery was in a weak state which affected the ignition neutral switch.
After I changed the battery and drove the car a few miles and when I stopped and placed it in Park the key came out with no problem.

Posted on Mar 03, 2009

5 Suggested Answers

  • 4 Answers

SOURCE: 2007 ford focus key stuck in ignition.

Hope this helps all.... If the key is stuck (won't come out) and the column is NOT locked, on the gear shift there is a plastic sleeve. Put the gear shift in park...slide your hand below the knob and pull that sleeve up! Presto!!! it locks in park and the key comes out. I just put all the stuff i took apart back together... the other solutions may work but this is the first step to check... no tools and you know right away...
AJay

Posted on Jul 03, 2010

  • 1 Answer

SOURCE: my key is stuck in my ford fusion

Bad switch, yeah right.. remove the sleeve around the button. I had a friend make one at a machine shop for super glued it in place not one problem since! Easy fic friend!~! Ford is making a killing off this problem!!!! LOL The other guy must be a service tech!

Posted on Jul 06, 2009

  • 25 Answers

SOURCE: Key won't come out of ignition on 2007 ford

do you have the steering wheel turned or any tension at steering wheel? wiggle your wheel while turning the key and it

Posted on Jul 08, 2009

awcforever
  • 359 Answers

SOURCE: when i turn my car off i can't remove the key from

Either the ignition cyllinder is locked up, or your gear shifter isn't set. Play with the shifter button on your shifter and try to remove the button. Should be a plastic cap. That cap gets jammed sometimes, and this prevents you from removing your key.

Posted on Mar 07, 2011

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key stuck in ignition in park. Check charging system comes on. Dealership says it might be a fuse.


Key Stuck in Ford Fusion (2006 model) - YouTube

? 1:21
https://www.youtube.com/watch?v=3LVQttFOzGA
Jun 18, 2014 - Uploaded by Jessica East
#Ford #Fusion #Key #ignition #Stuck #FordFusion2006. ... i have a 2006 mercury milan and my key got stuck in there last night,... it to park with a little bit of force. will see what happens next time. good video, nice to know.

Key Stuck in Ignition While in Park

www.2carpros.com/.../2007-ford-fusion-key-stuck-ignition-while-park
Dec 16, 2012 - KEY STUCK IN IGNITION / SHIFTER BINDING CONDITION FORD:2006-2007 Fusion LINCOLN: 2006 Zephyr MERCURY: 2006-2007 Milan

Nov 06, 2015 | 2006 Mercury Milan

1 Answer

Ford fusion stuck in park, engine won't start


It sounds like you have a dead battery. have it tested.

May 30, 2012 | 2007 Ford Fusion V6

1 Answer

2006 Mercury Milan key stuck in ignition.


There's a TSB published by ford for this condition. It's caused by a binding shifter button.


adobe.gif Printable View (73 KB) TSB
07-14-7
  • KEY STUCK IN IGNITION / SHIFTER BINDING CONDITION
Publication Date: July 6, 2007
FORD: 2006-2007 Fusion LINCOLN: 2006 Zephyr MERCURY: 2006-2007 Milan
This article supersedes TSB 07-2-1 to update the Part List. ISSUE: Some 2006-2007 Fusion, Milan and 2006 Zephyr vehicles built before 9/4/2006 may exhibit a customer concern of the ignition key getting trapped or a shifter slider binding condition. Most of the key trapped conditions are caused due to a binding shifter button which does not allow the pawl to contact the park detect switch.
ACTION: Follow the Service Procedure steps to correct the condition.
SERVICE PROCEDURE If the key will not release from the ignition cylinder lock follow the Key Trapped procedure. On vehicles with a hard-to-shift shift lever into park or slider bunching/binding then follow the Shifter Slider Binding procedure. Key Trapped:
  1. Actuate knob button 5-10 times, observe for binding or sticky condition.
  2. Replace knob assembly if the knob sticks following Workshop Manual (WSM), Section 307-05. NOTE: WHEN REPLACING THE SHIFT KNOB DO NOT REUSE THE SCREWS. REMOVE AND DISCARD THE SCREWS. INSTALL TWO NEW SCREWS AND TIGHTEN TO 18 LB-IN (2 N-m). DO NOT OVER TIGHTEN THE SCREWS OR DAMAGE MAY OCCUR.
Shifter Slider Binding:
  1. If shifter slider is bunched up or binding, replace bezel assembly following WSM, Section 307-05. NOTE: WHEN REPLACING THE BEZEL, CARE NEEDS TO BE TAKEN TO ENSURE THAT THE BRAKE SHIFT INTERLOCK OVERRIDE TAB IS PROPERLY ALIGNED INTO ITS GUIDE. REFER TO FIGURE 1.

    tb8706a.gif
    Figure 1 - Article 07-14-7

    NOTE: WHEN REINSTALLING THE SHIFT KNOB DO NOT REUSE THE SCREWS. REMOVE AND DISCARD THE SCREWS. INSTALL TWO NEW SCREWS AND TIGHTEN TO 18 LB-IN (2 N-m). DO NOT OVER TIGHTEN THE SCREWS OR DAMAGE MAY OCCUR. NOTE: IF OVERRIDE CAP IS DAMAGED DURING REPAIR, IT IS AVAILABLE SEPARATELY.

PART NUMBER PART NAME 6E5Z-7D443-B Bezel Asy-Black w/FNR5 Trans (Fusion-Milan) 6E5Z-7D443-C Bezel Asy-Black w/Aisin F21 Trans (Fusion-Milan) 6H6Z-7D443-A Bezel Asy-Satin Nickel (Zephyr) 6E5Z-7213-C Knob Asy-Black (Fusion-Milan) 6H6Z-7213-A Knob Asy-Charcoal (Zephyr) 6H6Z-7213-B Knob Asy-Charcoal-OD (Zephyr) 6E5Z-7A214-B Override Cap-Black (Fusion-Milan) 6H6Z-7A214-A Override Cap-Satin Nickel (Zephyr) W790088-S901 Screw (2 Req)
WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage
IMPORTANT: Warranty coverage limits/policies are not altered by a TSB. Warranty coverage limits are determined by the identified causal part.
OPERATION DESCRIPTION TIME 071407A 2006-2007 Fusion, Milan And 2006 Zephyr: Replace Knob Assembly, Includes Time To Diagnose And Verify Repair (Do Not Use With 04536A, 04536B, 7213A) 0.3 Hr. 071407B 2006-2007 Fusion, Milan and 2006 Zephyr: Replace Bezel Assembly Includes Time To Diagnose And Verify Repair (Do Not Use With 04536A, 04536B, 7213A) 0.4 Hr.
DEALER CODING BASIC PART NO. CONDITION CODE 7213 69

NOTE: The information in Technical Service Bulletins is intended for use by trained, professional technicians with the knowledge, tools, and equipment to do the job properly and safely. It informs these technicians of conditions that may occur on some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by "do-it-yourselfers". Do not assume that a condition described affects your car or truck. Contact a Ford, Lincoln, or Mercury dealership to determine whether the Bulletin applies to your vehicle. Warranty Policy and Extended Service Plan documentation determine Warranty and/or Extended Service Plan coverage unless stated otherwise in the TSB article. The information in this Technical Service Bulletin (TSB) was current at the time of printing. Ford Motor Company reserves the right to supercede this information with updates. The most recent information is available through Ford Motor Company's on-line technical resources.

Copyright © 2007 Ford Motor Company
2010&c18=non-tab%20view&c21=07-14-07&c35=tsb%2c07-14-07&s=1366x768&c=32&j=1.3&v=y&k=y&bw=778&bh=347&ct=lan&hp=n&[aqe]

Mar 08, 2011 | 2006 Mercury Milan

1 Answer

When i turn my car off i can't remove the key from the ignition. i have a 2007 ford fusion


Either the ignition cyllinder is locked up, or your gear shifter isn't set. Play with the shifter button on your shifter and try to remove the button. Should be a plastic cap. That cap gets jammed sometimes, and this prevents you from removing your key.

Mar 07, 2011 | 2007 Ford Fusion I4 SEL Sedan

1 Answer

Ford fusion 2006 keys stuck in the ignition how to get it out


YOU HAVE TO REMOVE IGNITION KEYLOCK CYLINDER.TO GET KEY OUT.KEYLOCK CYLINDER HAS TO BE REPLACED.

Jan 11, 2011 | Ford Fusion Cars & Trucks

1 Answer

My ford fussion 07 key is stuck in the ignition it turn but dont come out


Hello,
This is a common problem apparently. It seems like there is a plastic ring in the ignition switch that breaks off. I am not sure if your car is still under warranty, but here is a link to let you know more about the problem. Chances are your dealer has seen this before. They will have to replace the ignition it appears. I hope for your sake it is under warranty. God bless! Let me know how it goes:
http://www.ford-forums.com/ford-fusion/4432-keys-wont-come-out-ignition.html


Jun 26, 2010 | 2007 Ford Fusion I4 SEL Sedan

1 Answer

Keys stuck in the ignition


this may have the ignition key lock deal you push the key in and turn it back then itll release.

Apr 09, 2010 | 2006 Ford Fusion

1 Answer

Can't remove my key


not sure some Ford u have to push in a button to remove the key . Check and see if the model has that.

Jul 09, 2009 | 2007 Ford Fusion I4 SEL Sedan

2 Answers

Key won't come out of ignition on 2007 ford fusion? I removed the plastic ring from shifter and this did not fix the problem. thanks Joe


do you have the steering wheel turned or any tension at steering wheel? wiggle your wheel while turning the key and it

Jul 08, 2009 | 2007 Ford Fusion I4 SEL Sedan

Not finding what you are looking for?
2007 Ford Fusion I4 SEL Sedan Logo

3,013 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...