Question about 1998 Dodge Grand Caravan

1 Answer

Ignition Coil A,B,C Primary/Secondary malfunction

1998 dodge grand caravan wil not turn over. Error codes displayed coil problem. need help with how to fix. I am clueless as to where to look under the hood.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 6,784 Answers

Remove the Caravan Ignition Coil Step1 Look under the hood for a distributor. The spark plug wiresIgnition Coil A,B,C Primary/Secondary malfunction - mag-glass_10x10.gif connect into the distributor cap. If you don't see a distributor, you may have a model with a distributorless ignition system. Step2 Find the ignition coil. On a Dodge Caravan, the ignition coil is at the back of the intake manifold. Disconnect the negative battery cable to prevent injury while you work. Step3 Determine whether you need to remove the windshield wiper/motor module assembly. This won't be necessary on all models. Step4 Disengage the connector securing the wiring harness connector to the Dodge Caravan ignition coil. Then, disconnect the ignition wire from the ignition coil. Step5 Use a socket set to remove the mounting bolts. There are upper and lower mounting bolts. Separate the ignition coil from the mounting bracket. Install the New Ignition Coil Step1 Insert the new ignition coil. Mount the Dodge Caravan ignition coil to the mounting bracket. Step2 Attach the mounted assembly to the intake manifold. With a Torque wrench, tighten the fasteners securing the ignition coil to the mounting bracket with 96 inch pounds of torque (10 Nm). Step3 Tighten the bolts that secure the intake manifold to the bracket with 115 inch pounds of torque (13 Nm). Step4 Connect the wire harness and any other parts you removed, including the negative battery cable.

Posted on Feb 23, 2009

  • Michael Masters
    Michael Masters Feb 23, 2009

    This should help you. Thx for using Fix ya:)

  • crawford watkins
    crawford watkins Sep 21, 2015

    what if all 3 coils are malfunction

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

00 dodge dakota 4.7 codes p0353 and p0354 what that mean


code p 0353 refers to ignition coil C primary/secondary --circuit malfunction===causes ---wiring--ignition coil---ECM
code p 0354 refers to ignition coil D primary/secondary ---circuit malfunction===causes --wiring---ignition coil---ECM
check harness connections to the coils are clean and tight
replace the coils
check connections to the ECM

Nov 19, 2016 | Dodge Cars & Trucks

1 Answer

Dodge po353


Generic code for Ignition coil C primary/secondary circuit malfunction.

Aug 23, 2012 | 1998 Dodge Caravan

1 Answer

How to trouble shoot code p0360


P0360 - Ignition Coil '10' Primary/Secondary Circuit Malfunction

Ignition Coil Primary/Secondary harness is open or shorted
- Ignition Coil Primary/Secondary circuit poor electrical connection
- Faulty Ignition Coil Primary/Secondary
- Faulty Engine Control Module (ECM

Read more: http://engine-codes.com/p0360.html#ixzz21fHBlyUw

Jul 25, 2012 | Chevrolet Silverado 2500HD Cars & Trucks

2 Answers

2005 dodge grand caravan 3.8L code p2305 ignition coil b secondary circuit. has no spark on 2 of 6 cylinders. I have replaced the coil spark plug wires and spark plugs. found some broken wires for the...


Ouch! A case of the raucous rodent! I've been there...Not fun trying to track down and repair all the damage.

First of all, let me explain how the code sets: The computer monitors the PRIMARY side of the coil to determine the burn time on the SECONDARY side of the coil. This can be a little confusing. The code will set when the computer determines that secondary ionization (burn time) was too short, too long, or did not occur at all.
If you have confirmed that there is no spark at the spark plug wires, then that is why the code is setting...ionization is not occurring at all. What can be a little confusing is that this can be caused by a failure in the PRIMARY coil circuit even though the code is indicating that the computer is having a problem with the SECONDARY circuit. (The secondary circuit can malfunction even though the primary side is functioning perfectly, but if the primary side malfunctions, the secondary side ALSO malfunctions - it is impossible for the secondary side to work if the primary side is not working.)

So, I said all that to tell you this: I think you have pretty much eliminated the entire secondary side of the ignition by replacing the whole circuit. So the problem must be on the primary side. (Probably more chewed wires)
There are 4 wires going to your ignition coil. The BROWN/WHITE wire comes from the ASD RElay and supplies battery voltage to the coil assembly. Since the other four cylinders are firing, This wire has to be OK.
The code you are getting is for coil #2. This coil is controlled by computer through the DARK BLUE/TAN wire. If you disconnect your coil connector and probe this wire with a test light connected to the POSITIVE battery post, it should "blink" when to crank the engine over. My guess is that it will not be blinking. You can do this also on the BROWN/ORANGE (coil #1) wire and the DARK BLUE/DARK GREEN (coil #3) wire to see the difference.

Anyway, if the DARK BLUE/TAN wire does not blink, then the wire is broken (chewed?) between the coil and the PCM.

May 08, 2011 | 2005 Dodge Caravan

1 Answer

Codes p0351 miss and is goverened at 2800 rpms.


P0351 is Ignition Coil A Primary/Secondary Circuit Malfunction.
Possible causes: - Open or short in the ignition coil circuit - Ignition coil circuit shorted to ground - Ignition coil connector - Damaged ignition coil - Damaged PCM or
Possible solution - If damage, repair ignition coil circuit - Replaced ignition coil - Replaced PCM or ECM When is the code detected? The test fails when the Powertrain Control Module (PCM) or Electronic Control Module(ECM) does not receive a valid pulse signal from the ignition coil.
P0351 Description: The ignition signal from the Powertrain Control Module (PCM) or Electronic Control Module(ECM) is sent to and amplified by the power transistor. The power transistor turns ON and OFF the ignition coil primary circuit. This ON/OFF operation induces the proper high voltage in the coil secondary circuit.
Hope this helps :)

Mar 07, 2011 | 2002 Dodge Intrepid

1 Answer

I have no spark in cylinders 2,4,6 on my 2002 Ford escape and three codes 354,355,356 Which means the same . After checkin those Three coils I found out , there is no negative Any advise?


P0354 - Ignition Coil D Primary/Secondary Circuit Malfunction.

Description of DTC:
The ignition signal from the Powertrain Control Module (PCM) or Electronic Control Module(ECM) is sent to and amplified by the power transistor. The power transistor turns ON and OFF the ignition coil primary circuit. This ON/OFF operation induces the proper high voltage in the coil secondary circuit.

Symptoms:
- Lack/Loss of Power
- The engine may be harder to start
- Engine hesitation
- Check Engine Light On
- No spark

Possible Causes:
- Open or short in the ignition coil circuit
- Ignition coil circuit shorted to ground
- Ignition coil connector
- Damaged ignition coil
- Damaged PCM or ECM

Possible Solutions:
- If damage, repair ignition coil circuit
- Replace ignition coil
- Replace PCM or ECM



P0355 - Ignition Coil E Primary/Secondary Circuit Malfunction.

P0356 - Ignition Coil F Primary/Secondary Circuit Malfunction.

Jan 18, 2011 | 2002 Ford Escape

1 Answer

Miss fires and stots off when I give it gas as codes 1391 ,0351, 0352, 0353,


P1391 - Not a valid obd code.
B1391 - Oil Level Switch Circuit Failure
C1391 - Not a valid obd code.
U1391 - Not a valid obd code.
Its possible you may have misread this code. If it is B1391 that would be the only code with 1391 for your vehicle.

P0351 - Ignition Coil A Primary / Secondary Circuit Malfunction. The ignition signal from the Powertrain Control Module or Electronic Control Module is sent to and amplified by the power transistor. The power transistor turns ON and OFF the ignition coil primary circuit. This ON/OFF operation induces the proper high voltage in the coil secondary circuit.

Possible Causes:
- Open or short in the ignition coil circuit
- Ignition coil circuit shorted to ground
- Ignition coil connector
- Damaged ignition coil
- Damaged PCM

P0352 - Ignition Coil B Primary / Secondary Circuit Malfunction.
Same repair info as P0351.

P0353 - Ignition Coil C Primary / Secondary Circuit Malfunction.
Same repair info as P0351



Solutions:
- If damage, repair ignition coil circuit
- Replaced ignition coil
- Replaced
PCM or ECM

Jan 16, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

97 dodge grand caravan es 3.8. I keep getting code


CODE PO353 IGNITION COIL C PRIMARY SECONDARY CIRCUIT FAILURE MALFUNCTION.

Jul 25, 2010 | Dodge Grand Caravan Cars & Trucks

1 Answer

Engine codes P0354 P0351 engine skips low power


These codes are for a malfunctioning ignition coil/s.
P0351= ignition coil A primary/secondary circuit malfunction.
P0354= ignition coil D primary/secondary circuit malfunction.
visually check the coil packs for burn marks, damage, loose wire connectors, and the wire harness to each of the coils for damage. How long has this been happening? Has any work been done recently? Did the engine compartment recently get wet?

May 23, 2010 | 2000 Dodge Durango

Not finding what you are looking for?
1998 Dodge Grand Caravan Logo

544 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

69199 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6817 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...