Question about 1996 Dodge Caravan

1 Answer

I need a engine diagram for a 1996 caravan with a 3.0 ltr. the front area where timming belt and harmonic balance is.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 6,674 Answers

Check this link, scroll down to 3.0L engine, and also see fig# 13. click on picture to expand/enlarge.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528003c39d

Posted on Feb 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a diagram of where the front main seal is on a 93 2.5 4cyl dodge caravan 5 speed ive been told I just need to pull a pulley and the seal should be right there


you do have to take of that pully also the timming cover timming belt timming gear but first you have to put the engine to top dead center on time beafor you do all that ok good luck

Sep 07, 2013 | 1993 Dodge Caravan

1 Answer

1998 dodge grand caravan serpentine belt directions,diagram 3.3 ltr


0900c1528003c191.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 11: Accessory drive belt adjustment-3.3L and 3.8L engines
All of the belt driven accessories on the 3.3L and 3.8L engines are driven by a single serpentine belt. The belt tension is maintained by am automatic tensioner.

  1. Disconnect the negative battery cable.
  2. Raise the front of the vehicle and safely support it with jackstands.
  3. Remove the right front splash shield.
  4. Release tension by rotating the tensioner clockwise.
  5. Remove the belt and install a replacement.
  6. Proper belt tension is maintain by the dynamic tension.
  7. Install the right front splash shield. Lower the front of the vehicle.
  8. Connect the negative battery cable

May 03, 2012 | 1998 Dodge Grand Caravan

1 Answer

How do I replace a crankshaft censor? Do you have a diagram?


Crankshaft sensor would be mounted close the the harmonic balancer pulley. It senses the rotation of the engine. It would have a magnet and copper coil winding inside similar to the coil in a speaker cone. When metal passes by the device in close proximity such as a rotating pulley, it induce small amount of electric current. The harmonic balancer pulley would have notch on it so the when that notch passes through the sensor it would cause a sudden drop in in current and that is how it senses the the position of the crankshaft. So look where all the belts are at the main pulley that drives all the belt is the harmonic balancer. You would see a pair of wires connected to it. If you see a small device mounted close to it in such a way so it senses its rotation thats the crankshaft position sensor.

Jun 26, 2010 | 1992 Dodge Grand Caravan

1 Answer

I'am trying to set the timing for a 96 mit.eclipse


you have to line up all 3 of your tjmjng marks.Is your engine single head or double overhead cams The marks have to line up.Firstyou have to remove the belt.Then remove harmonic balancer to get to the timing gear sprocket.It has a blade attached to it with 3 fins in between the fins is a little dip that is the crankshaft position.align that dip with the mark below the crankshaft position sensor.then you have to do the same with your camshafts.Then replace the belt and spin the the crankshaft clockwise to the aligment mark they should all stop on their marks.

Apr 18, 2010 | 1996 Mitsubishi Eclipse

1 Answer

1998 grand cherokee limited crankshaft crack?


To identify the crankshaft, with the belt removed, it is the only item that will turn when you crank the engine over.
I've seen harmonic balancers fail but rarely a crankshaft.
Some P/S systems will "push" some fluid out when you steer without the pump running. Concentrate on repairing/replacing the balancer, then re-diagnose the P/S problem after that is taken care of.

Dec 15, 2009 | 1996 Jeep Grand Cherokee

2 Answers

How to remove the harmonic balancer pulley on a '96 dodge caravan 3/0L?


i have a 1998 caravan my harmonic balancer fell off my qquestion is is there 2 separate keys that hold on the timing gear and the balancer pulley on, i have been to the dodge dealer and they printed me out pics but i still don't know for sure if the timing gear has it's own key or there is just 1 long key that holds both the timing gear and the balancer ......PLEASE HELP

Nov 22, 2009 | 1996 Dodge Caravan

1 Answer

I cant find my crank sensor


The 3.0 doesn't have a crank sensor. It has a pick-up in the distributor for crank reference. But this wouldn't keep the engine from cranking. Is the old belt wrapped up around the harmonic balancer causing it to lock up?

Apr 08, 2009 | 1996 Dodge Caravan

1 Answer

Harmonic balancer bolt direction for loosening??


CCW , and your going to at least put the new timing belt on and balance to check for compression. you can run an engine without the covers installed or accessories hooked up

Feb 05, 2009 | 1996 Isuzu Rodeo

2 Answers

Bearing


check your harmonic balancer they where notorius for going bad on buicks.Remove the belt and grab the balancer and see if you can rock it back and forth by hand. if you can its the balancer

Sep 21, 2008 | 1996 Buick LeSabre

Not finding what you are looking for?
1996 Dodge Caravan Logo

Related Topics:

273 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...