Question about 2000 Mazda MPV

1 Answer

Indentication of the two "pistons" that hold up hatchback door

These two parts need to be replaced

Posted by on

  • Mike Butler
    Mike Butler May 11, 2010

    Is there supposed to be pictures somewhere?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mazda Master
  • 64,052 Answers

Lift gate support gas cylinders is what they are called

Posted on Mar 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine diagram


check for indent or small slot on crown of piston. This faces to the front of the engine (Timing cover end) con-rods will also need to be in the pistons correctly

May 18, 2013 | 2006 Ford Bantam 1.6i

1 Answer

The hatch back hatchback door on my hatchback hydunai 2008 accent won't stay open when the door is opened and lifted up, how do you fix this


You might want to replace the two holding levers positioned on the left and right side of the hatchback door.

Jul 08, 2012 | 2007 Scion xA

1 Answer

How do I fix the door/lock of my 1991 Acura Integra? I can only open the driver side door from the outside


There are only 2 places that you have the problem on the inside door handle. one is at the handle,and the little plastic holder that holds the rod to the handle broke, or the plastic clip the the door lock mechanism broke. the first can be removed without taking the door apart. the inside door handle has a screw holding it in place. you can remove the handle and see if its broken. the second requires you to remove the door panel, to replace the clip that hold the rod to the lock. I door handle in the car is a dealer item only(sorry to tell you that), the clip for the lock, you can get at the auto parts store. hope this helps

Jan 11, 2011 | 1991 Acura Integra Hatchback

1 Answer

How to replace rear pads on 2002 saturn


You will need to unbolt the caliper, usally 2 bolts, take the caliper off the rotor, remove the pads. You will need a larger c-clamp or a caliper piston tool to compress the piston, if there are two indentations in the face of the cylinder piston, you will need a brake tool to turn the piston, clockwise a few times press in the piston and repeat until the piston is completely back into the caliper. Install the new pads and put the caliper back on. Make sure you pump up your brake peddle a few times after the job, before you take off.

Mar 11, 2010 | Saturn S-Series Cars & Trucks

2 Answers

My 1998 range rover hatchback will not unlock.all


: The keyfob may have lost synch, put the key in the door and turn to lock, hit the lock button and hold for a second. then do the same for unlock.

Dec 24, 2009 | 1995 Land Rover Discovery

3 Answers

How do you push the piston back into the caliper when replacing the brakes on a MAXX LT.


Most pistons can be pushed back in with a wooden hammer handle, or similar, after loosening bleeder.

Aug 19, 2009 | 2007 Chevrolet Malibu Maxx LTZ Hatchback

4 Answers

1996 olds aurora back brake pad replacement, how to compress the pads to get the caliper back over the pads?


Special tool is a 1" cube with tabs on each side that fits into indentations on the brake piston and can be purchased for $10-12 @ most discount parts stores. Use 3/8" ratchet with short extension and 'special tool to carefully turn piston onto internal hand brake screw. Take care to not tear dust boot. When piston is fully collapsed, make sure to align piston indentations perpendicular to brake pad as there are bumps on pad that fit into them. Also while screwing in piston either remove about 2/3 of brake fluid in master cylinder and refil afterwords or open the bleeder valve on brake piston assembly. Bleed if necessary.

Jul 18, 2009 | 1996 Oldsmobile Cutlass Supreme Coupe

1 Answer

Contiuous beeping of Lexus hatchback sensor


you have a Bad Door Sensor and need to replace it to get this Beeping to stop. Go to the Back and Hold in the Switch with your Finger and see if it will stop.

Jan 19, 2009 | 2006 Lexus Gs 300

1 Answer

Changing rear brakes on a 2001 volkswagon jetta


You probably have a screw-in caliper piston design like my 99 A4 has. You need a tool that is made for screwing the calipers in - AutoZone has them as part of their tool loan program. Look at the face of the piston - if you see two indents or notches across from each other on the face, then you have screw-in pistons and need the kit to do them.

Jul 25, 2008 | 2000 Volkswagen Golf

Not finding what you are looking for?
2000 Mazda MPV Logo

Related Topics:

255 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

64052 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...