Question about 1998 Plymouth Grand Voyager

1 Answer

What is it called? bar from strut to stabilizer arm?

1998 Grand Voyager, bar broke and I don't know what it is called.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 359 Answers

If on the front end, you will have the spring, with the strut coming down in the center, then you will have a sway bar with a thin rod that connects to the arm, then you will have a small rod coming straight out with a boot and nut on the end at a 90deg angle, and that will be the tie rod and tie rod end. And in the center of the wheel will be your axle, I hope I described what you are looking for. Good luck

Posted on Feb 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change the front coil spring on my 2 litre td suzuki grand vitara


you broke that spring, really< or is this another job? do say job .
no year, wow, that does make it hard,
as all books are indexed by year, first.
so i cant get off the dime. (parked here)

ill guess and its a 2000.
car has struts.
alldata.com (DIY)

I never do change, just remove. sorry, login and read it all.

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Support the vehicle at the frame with a hoist or jackstand.
  3. Support the control arm with a floor jack.
  4. Remove or disconnect the following:
    • Front wheel
    • Brake caliper and rotor
    • Locking hub or drive flange, if equipped
    • Axle shaft snapring and thrust washer, if equipped
    • Wheel speed sensor, if equipped
    • Stabilizer bar link
    • Lower ball joint
    • Strut bracket bolts
  5. Lower the floor jack and remove the coil spring.

Feb 23, 2015 | Suzuki Cars & Trucks

1 Answer

What is piece called


part of the steering linkage or a stabilizer bar ?

Feb 01, 2014 | 1998 Jeep Grand Cherokee

2 Answers

2004 chrysler pacifica is clunking on very small bumps. Not during braking though. I've looked at struts and they seem okay. Nothing loose that I can see or feel. Ideas?


JACK UP THE FRONT OF THE CAR AT THE FRAME TILL THE TIRE IS OFF THE GROUND.THEN TRY MOVING THE STRUT AND THE SPRING!!ALSO LOOK AT THE SWAY BAR LINKS CONNECTED TO THE LOWER A ARM OR STRUT!!

Nov 16, 2013 | Cars & Trucks

2 Answers

I'm trying to change my struts on my 1994 ford thunderbird. I bought the full assembly with the springs and everything already together.. How do I go about doing this?


  1. Remove plastic cover at upper strut mount. Remove automatic ride actuator (if equipped). Remove 3 upper strut retaining nuts and collar plate from the mounting studs in engine compartment.
  2. Raise vehicle on hoist. Remove tire and wheel assembly. Remove lower strut mounting bolt and nut. Remove nut at stabilizer link upper mounting stud. Separate link studs from spindle and stabilizer bar using Joint Separator.
  3. Support lower control arm assembly with jack. Raise control arm with jack until stabilizer link can be separated from spindle. Position link aside.
  4. Remove and discard spindle to upper control arm nut and bolt. Lower jack to separate spindle form upper control arm. Support spindle aside with wire or other means. Remove jack from lower control arm and remove strut assembly.
  5. Reverse disassembly instructions to install new strut on each side.
  6. Check alignment/have vehicle aligned.

Jun 02, 2011 | Ford Thunderbird Cars & Trucks

1 Answer

Front end bushings what are they how are they


Well there are stabilizer bar bushings, control arm bushings and strut mount bushings. The stabilizer bushings are usally bolted around the the stabilizer bar and attach to the frame. The control arm bushings are usally pressed into the control arms. The strut mount bushings are on top of the struts. Normally they are replaced as needed. The strut mount bushings are good to do when replacing the struts.

Mar 12, 2010 | 2005 Subaru Outback

1 Answer

How to change 1998 Plymouth grand Voyager front sway bars


unbolt the sway bar links from the control arms and the two brackets holding it to the frame. make sure if you jack it up jack up the front end. if you jack up one side and not the other and take the sway bar loose it will be loaded and could cause injury if not careful as long as both front tires are off the ground the sway bar will not be loaded and will be safe to deal with

Oct 19, 2009 | 1998 Plymouth Grand Voyager

1 Answer

Replacing front struts


Okay....here is the steps first....and then the directions on how to use the tools:

  1. Raise and properly support the vehicle.
  2. Remove the front wheel.
  3. Detach the shock absorber lower mount by removing the two bolts.
  4. Remove the retainer nut, retainer, cushion and shock absorber.
  5. Detach the cushion retainer from the shock absorber.
  6. Compress the coil spring with a commercially available spring compressor.
  7. Detach the stabilizer bar.
  8. Support the upper suspension arm and steering knuckle securely.
  9. Remove the cotter pin.
  10. Loosen and remove the nut.
  11. Using a ball joint removal tool, detach the lower ball joint from the lower control arm.
  12. Loosen the suspension arm set bolt.
  13. Remove the suspension arm set bolt nut.
  14. Remove the nut from the strut bar front set bolt.
  15. Pull out both set bolts.
  16. Remove the lower suspension arm and coil spring. To install:
  17. Installation is the reverse of removal. Note the following torque specifications:
    1. Strut bar front set bolt: 221 ft. lbs. (300 Nm)
    2. Lower suspension arm set bolt: 148 ft. lbs. (200 Nm)
    3. Lower ball joint nut: 80 ft. lbs. (110 Nm)
    4. Lug nuts: 83 ft. lbs. (110 Nm).

May 13, 2009 | 1998 Toyota Tacoma

1 Answer

Front Sway bar(Stabilizer bar)


please give good rating if this helps


Section 04-01: Suspension and Wheel Hubs, Front 1996 Taurus, Sable Workshop Manual REMOVAL AND INSTALLATION Stabilizer Bar Removal
  1. Raise vehicle on a hoist. Refer to Section 00-02 .
  1. Support vehicle with hoist or safety stands behind front sub-frame (5C145).
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use extreme care not to damage boot seal. Do not use power tools to tighten nut, or bearing and seal damage will result. Install nut using hex hold feature to prevent the stud from rotating.
    Remove and discard nuts retaining stabilizer bar link (5K484) assembly to front stabilizer bar (5482) and front shock absorber (18124) with an 8 mm closed-end wrench and an 18 mm open-end wrench.


    ccf2026.gif

  1. Remove nuts retaining steering gear (3504) to front sub-frame, and move steering gear off the front sub-frame.
  1. With another set of support safety stands under front sub-frame, remove two rear subframe retaining bolts. Lower rear of the front sub-frame to obtain access to stabilizer bar brackets (5486).




  1. Remove front stabilizer bar U-bracket bolts and replacestabilizer bar brackets and/or front stabilizer bar as required. Discard lower suspension arm stabilizer bar insulator (5493) and bolts.
Installation
  1. Clean front stabilizer bar to remove dirt and contamination in area of stabilizer bar insulator installation position.
  1. Lubricate inside diameter of new lower suspension arm stabilizer bar insulator with Rubber Suspension Insulator Lube E25Y-19553-A or equivalent meeting Ford specification ESF-M99B112-A. Do not use any mineral or petroleum based lubricants as they will deteriorate the rubber lower suspension arm stabilizer bar insulators.
  1. Install new lower suspension arm stabilizer bar insulators onto front stabilizer bar and position them in approximate location.
  1. Install stabilizer bar bracket on front sub-frames and install new bolts. Tighten to 30-40 Nm (22-29 lb-ft).
  1. Raise front sub-frame and install new front sub-frame-to-body retaining bolts. Position steering gear onto front sub-frame and install retaining nuts. Tighten to 115-135 Nm (85-99 lb-ft).
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use extreme care not to damage boot seal. Do not use power tools to tighten nut, or bearing and seal damage will result. Install nut using hex hold feature to prevent the stud from rotating.
    Install stabilizer bar link to front shock absorber and to front stabilizer bar, making sure that the stabilizer bar link is properly positioned. The letters "Top LH" and "Top RH" are moulded into the stabilizer bar link for correct assembly to the front shock absorber strut.
  1. Install new nuts and secure stabilizer bar link assembly to front stabilizer bar and front shock absorber. Tighten to 77-103 Nm (57-75 lb-ft) at front shock absorber strut and 47-63 Nm (35-46 lb-ft) at front stabilizer bar.
  1. Remove safety stands.
  1. Lower vehicle.

Apr 11, 2009 | 1995 Ford Taurus

1 Answer

1998 Ford Escort clunk under LF over bumps


Hi the most common fault on escort suspension is worn track control arm bushes followed by anti roll bar bushes i think you call them stabiliser bushes i would agree with your ford tech guy re the strut bushes let me know if it solves it

Mar 26, 2009 | 1998 Ford Escort

Not finding what you are looking for?
1998 Plymouth Grand Voyager Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...