Question about 2004 Jeep Grand Cherokee

1 Answer

Passenger rear power window does not work, other 3 windows do work

Posted by on

  • jnsmith3800 Apr 11, 2009

    2004 Jeep Grand Cherokee rear window will go down but not come back up. Going down can hear the motor, try to get it back up -no sound at all. Wiring issue?

  • Razr4lfe May 14, 2009

    i have to same problem except i just replace to motor/regulator assembly

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 512 Answers

Possible a bad motor assembly or wiring problem...id bet motor /regulator assembly is bad

Posted on Feb 22, 2009

5 Suggested Answers

AutoDoc
  • 169 Answers

SOURCE: passenger window will not rais

Remove the door panel and unplug the window lift motor. Connect a test light across the harness plug and try the switch in both directions. If it lights in both the motor is bad or the regulator is stuck. You can put an ammeter in line and apply power again. If the amperage is high,the regulator is probably stuck. Good Luck.

Posted on Aug 25, 2008

emissionwiz
  • 60985 Answers

SOURCE: 2005 Camry rear right Power window not working

Like I said you need a new window lift motor.

Posted on Aug 27, 2008

  • 39 Answers

SOURCE: passenger window and rear vent window stopped working

YOU PROBABALY MAVE A BROKEN WIRE IN THE HARNESS THAT GOES FROM THE DRIVERS DOOR TO THE INSIDE OF THE VEHICLE

Posted on Jul 24, 2009

  • 1986 Answers

SOURCE: no power to the passenger rear window

I assume you've tried with the driver's door switch and the rear passenger switch and nothing happens. If so, then it's unlikely that both switches went bad and it points to a bad motor...
You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. You can test the switches at this point to see if they work. If not, you can then pull off the weather seal and access the regulator, motor inside the door that will be held in by several bolts

Posted on Aug 24, 2009

dttech
  • 4803 Answers

SOURCE: rear window and passenger windows will not

The last couple of times I have seen this complaint, the "Lock" button on the master (driver's door) switch had been depressed. Unlatching the lock button (pushing it again) solved the problem. On most cars, when the lock button is depressed, the windows can still be operated by the driver, but prevent the windows from being operated by the passengers. Toyota is different. If the lock button is depressed, nobody, including the driver can work the wndows.

Posted on Oct 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the right front door panel on a 2004 buick le saber


Did you test it or are you guessing just because it won't open or close ? How To Install Remove Front Door Panel Buick Lesabre 00 05 1AAuto com both right an left are the same .
Power Windows System Components
The following components are used to control the power windows:
?€¢
Driver Door Module (DDM)


?€¢
Passenger Front Door Module (PDM)


?€¢
LH Rear Door Module (LRDM)


?€¢
RH Rear Door Module (RRDM)


?€¢
Driver Door Switch Assembly (DDSA)


?€¢
RH Front Power Window Switch


?€¢
LH Rear Power Window Switch


?€¢
RH Rear Power Window Switch


?€¢
LH Front Power Window Motor


?€¢
RH Front Power Window Motor


?€¢
LH Rear Power Window Motor


?€¢
RH Rear Power Window Motor


?€¢
Class 2 serial data circuit


?€¢
Power door serial data circuit


?€¢
PWR WDO 30 Amp Circuit Breaker


?€¢
DRVMDL Fuse (10 amp)


Driver Door Switch Assembly and Driver Door Module logic, Driver Door Module internal driver operation


?€¢
PASS MDL Fuse (10 amp)


Front Passenger Door Module logic and internal driver operation


?€¢
RRDR MDL Fuse (10 amp)


Left Rear Door Module and Right Rear Door Module logic and internal driver operation


Do you know about computer controlled power windows ?
Power Windows Operation
The vehicle is equipped with power windows controlled by the door modules. Each passenger door window can be operated, either from a switch built into the driver door switch assembly (DDSA), or from a switch mounted locally to its associated door. The driver door window can be operated only from the driver door window switch built into the DDSA.
When a window is operated from the DDSA, the DDSA interprets the window switch signal as a specific window switch request and sends the information to the driver door module (DDM) via the power door serial data circuit. The DDM examines the request and checks to see if it has received any class 2 serial data messages from any of the other vehicle modules (i.e. ignition switch position) prohibiting the movement of the window. If the window being operated is the driver door window, and if no prohibitive class 2 messages have been received, the DDM then applies voltage and ground to the driver door window motor to move the window glass as requested. If the window being operated is a passenger door window, and no prohibitive class 2 messages have been received, the DDM sends the request, via the power door serial data circuit, to the appropriate passenger door module. The passenger door module then applies voltage and ground to the passenger door window motor to move the window glass as requested.
When a passenger door window is operated from the power window switch mounted locally to its associated door, the passenger door module first checks to see if the DDM has received any prohibitive class 2 serial data messages. If there are no prohibitive messages, the passenger door module powers the associated passenger door window motor.
Both front door windows have the express down feature. This allows the front door windows to be fully opened by momentarily pulling the appropriate window switch lever to the second detente and then releasing.

Oct 30, 2016 | Buick Cars & Trucks

1 Answer

2003 gmc envoy Windows fuse


Are all windows not working ? Two separate circuit breakers left & right . Both in rear fuse box . Fuse Block - Rear Beneath the left rear seat
Check for broken wires inside the rubber boot from body to doors.
Do you know about electronic control modules ?
The power window system consists of the following components:
?€¢
Driver door module (DDM)


?€¢
Passenger door module (PDM)


?€¢
Body control module (BCM)


?€¢
LR power window switch


?€¢
RR power window switch


?€¢
Window up and window down relays in each of the rear passenger window switches


?€¢
Window lockout switch


?€¢
Reversible power window motors in each of the doors (circuit breaker protected)


?€¢
LT DOOR CB 25A (System power for left rear window)


?€¢
RT DOOR CB 25A (System power for right rear window)


The power window system will operate anytime the retained accessory power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The DDM contains 4 power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the 2 front windows have 3 positions Up, Down and Express Down, while the switches for the rear windows have only 2 positions, Up and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has 2 positions Up and Down. Each of these switch positions is a direct input to the PDM.
The 2 rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a class 2 message from the DDM, can control the set of relays which will activate the rear window motors.

Check

Oct 21, 2016 | 2003 GMC Envoy

2 Answers

Driver door will not work lock or windows


They hooked into wiring they shouldn't have >
Power Window System Components
The power window system consists of the following components:
?€¢
Driver door module (DDM)


?€¢
Passenger door module (PDM)


?€¢
Body control module (BCM)


?€¢
LR power window switch


?€¢
RR power window switch


?€¢
Window up and window down relays in each of the rear passenger window switches


?€¢
Window lockout switch


?€¢
Reversible power window motors in each of the doors (circuit breaker protected)


?€¢
LT DOOR CB 25A (System power for left rear window)


?€¢
RT DOOR CB 25A (System power for right rear window)

Power Window System Controls
The power window system will operate anytime the retained accessory power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The DDM contains 4 power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the 2 front windows have 3 positions Up, Down and Express Down, while the switches for the rear windows have only 2 positions, Up and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has 2 positions Up and Down. Each of these switch positions is a direct input to the PDM.
The 2 rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a class 2 message from the DDM, can control the set of relays which will activate the rear window motors.

Jan 10, 2016 | 2004 GMC Envoy

1 Answer

Is there a fuse for the window switch


Which window switch ? RT DOOR CB-circuit breaker , do you know what a circuit breaker is ? 25A (System power for right rear window)
LT DOOR CB 25A (System power for left rear window
The power window system will operate anytime the retained accessory power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The DDM contains 4 power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the 2 front windows have 3 positions Up, Down and Express Down, while the switches for the rear windows have only 2 positions, Up and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has 2 positions Up and Down. Each of these switch positions is a direct input to the PDM.
The 2 rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a class 2 message from the DDM, can control the set of relays which will activate the rear window motors.


The power window system consists of the following components:
?€¢
Driver door module (DDM)


?€¢
Passenger door module (PDM)


?€¢
Body control module (BCM)


?€¢
LR power window switch


?€¢
RR power window switch


?€¢
Window up and window down relays in each of the rear passenger window switches


?€¢
Window lockout switch


?€¢
Reversible power window motors in each of the doors (circuit breaker protected)


?€¢
LT DOOR CB 25A (System power for left rear window)


?€¢
RT DOOR CB 25A (System power for right rear window)


If you not sure about any of this I suggest you take your vehicle to a ASE certified repair shop .

Oct 08, 2015 | 2002 Chevrolet TrailBlazer

1 Answer

I need the wiring schematics for driver door panel and all switches in a 2003 Chevy Tahoe. My window won't go down on that side and I'm sure I have a short somewhere because my switch works with all other...


You don't know what your getting into , The door switches have electronic control modules incorporated ,DDM- Driver door module an PDM passenger door module .
The power window system consists of the following components:
?€¢
Driver Door Module (DDM)


?€¢
Passenger Door Module (PDM)


?€¢
Body Control Module (BCM)


?€¢
RR power window switch


?€¢
Window up and window down relays in each of the rear passenger window switches


?€¢
Window lockout switch


?€¢
Reversible power window motors in each of the doors (circuit breaker protected)


?€¢
LT DOOR CB 25A (System power for left windows)


?€¢
RT DOOR CB 25A (System power for right windows)


The DDM contains four power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the two front windows have three positions UP, Down and Express Down, while the switches for the rear windows have only two positions, UP and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a Class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has two positions Up and Down. Each of these switch positions is a direct input to the PDM.
The two rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a Class 2 message from the DDM, can control the set of relays which will activate the rear window motors.
You need a scan tool to diagnose these systems
Power Window Inoperative - Driver Door

1

Did you perform the Door Systems Diagnostic System Check?
Go to Step 2
Go to Diagnostic System Check - Door Systems

2

Operate the driver power window in the UP and DOWN directions.
Does the driver power window operate properly?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
Go to Step 3

3

  1. Install a scan tool.
  2. Monitor the driver window status data parameter in the driver door inputs list.
Does the driver window status data parameter display an active state?
Go to Step 11
Go to Step 4

4

  1. Monitor the driver window status data parameter in the driver door module inputs list.
  2. Activate the driver power window switch in the up and down positions.
Does the driver window status data parameter change accordingly?
Go to Step 5
The data link connector (DLC) allows a scan tool to communicate with the class 2 serial data line. The serial data line is the means by which the microprocessor-controlled modules in the vehicle communicate with each other. Once the scan tool is connected to the class 2 serial data line through the DLC, the scan tool can be used to monitor each module for diagnostic purposes and to check for diagnostic trouble codes (DTCs). Class 2 serial data is transmitted on a single wire at an average of 10.4 kbps.

You

Mar 24, 2015 | Cars & Trucks

1 Answer

3 of my 4 power windows stopped working on my 2002 PT cruiser


Sounds like a fuse. Find the fuse box when you visit Autozone and get the fuse replaced.

Mar 09, 2014 | Cars & Trucks

2 Answers

Power windows on 3 of 4 dont work on 1997honda crv


most likely the switch got wet. unplug and check conections

Mar 14, 2013 | Honda CR-V Cars & Trucks

6 Answers

Windows won't roll down


Does the rear window work from the passenger switch?

Oct 07, 2009 | 2003 Cadillac CTS

1 Answer

98 chevy blazer power window issue


sugest fuse ck 1st thing. Master bypasses individual controls. Power supply to rear windows is interupted. Ck for connevtor under front seats. Fuse may be labrled accessory or per win.

May 12, 2009 | 1998 Chevrolet Blazer

1 Answer

Rear side windows


This may be just a case of inadvertently hitting the window lock out n th driver door window switch by mistake. Check that first. Here's some background on window operation

Principles of Operation
The driver power window regulator motor is controlled directly by the master window/door lock/unlock switch (and its integrated "auto down" module). Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The driver power window regulator motor is a reversible motor that is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The passenger power window regulator motor is controlled directly by the passenger power window switch and can also be controlled by the master window/door lock/unlock switch. Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The passenger power window regulator motor is a reversible motor, which is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The power rear quarter glass is also directly controlled by the master window/door lock/unlock switch. The power rear quarter glass power latches also utilize reversible motors. The power rear quarter glass power latches are operated by applying power and ground to the motor leads to open the window, and then reversing polarity on those same leads to close the window.
Symptom Chart Condition Possible Sources Action
  • All windows are inoperative
  • BJB Fuse:
    • F20.
  • Circuit.
  • Power window relay.
  • Front door power window switch.
  • GO to Pinpoint Test A .
  • Single power window is inoperative
  • Front door power window switch.
  • Front door power window regulator.
  • Circuit.
  • Driver door power window switch.
  • GO to Pinpoint Test B .
  • Vent power window is inoperative — quarter window glass power latch
  • Circuit.
  • Quarter window glass switch.
  • Quarter window glass power latch.
  • GO to Pinpoint Test C .
  • The one touch down feature is inoperative
  • Master window regulator and door lock switch.
  • INSTALL a new master window/door lock/unlock switch. REFER to Switch—Master Window Door Lock/Unlock .
  • The back window will not defrost
  • CJB Fuses:
    • F30 (10A).
    • F32 (20A).
    • F34 (20A).
  • BJB Fuse:
    • F27 (45A)
  • Circuit.
  • Heated back window switch.
  • SEC/timer module.
  • Rear window defrost relay.
  • GO to Pinpoint Test D .
  • The back window defrost will not shut off automatically
  • SEC/timer module.
  • Circuit.
  • Rear window defrost relay.
  • GO to Pinpoint Test E .

Jan 28, 2009 | 1999 Mercury Villager

Not finding what you are looking for?
2004 Jeep Grand Cherokee Logo

Related Topics:

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...