Question about 2000 Jaguar S-Type

1 Answer

Timing and firing order

A technican open my cylinder head for the gasket replacement, but they can not get the timing non the firing order of the engine bask

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 74 Answers

Hi the firing order is 1 5 3 6 2 4

Posted on Mar 06, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Only three cylinder fire


Have you checked the valve clearence on number three piston It will not fire if the valves are held slightly open.

Mar 10, 2013 | Cars & Trucks

3 Answers

I have 2003 chevy impala (V6 3.4 liter) i recently replaced both head gaskets. The car was running fine and now with engine back together engine want turn over sounds like its not firing but the plugs...


Did you get the timing set correctly when you reattached the cam to the timing chain? It sounds like you didn't have the #1 Top dead center or the cams were in the wrong position when you reset the timing chain. The cam shaft and Crank will actually look like they are set correctly two times. Once when it is in time and once when it is out of time 180 degrees. If you are more than 5 degree out of time or more than 5 degrees from the point where it is 180 degrees out of time the engine normally won't fire at all. The easiest way to check and verify this is to do compression checks on the cylinders, you will find you have little or no compression on several cylinders if this is the case. To correct it remove the timing chain and set the crank to #1 Top Dead center. Then go to the head that is on the #1 side, line the cam up so that both valves are closed for the number 1 and line that mark up. You have to find the firing order to make sure the intake is open getting ready to close for the next cylinder that going to fire and the exhaust valve is closed, then make teh final adjustment to line that cams timing mark up then replace the timing chain. This should get everything roughly within 5 degrees of zero and should get the motor so it will start.

Mar 02, 2011 | 2003 Chevrolet Impala

1 Answer

Cylinder layout and coil pack numbers for 1993


try this. firing order is 1,2,3,4,5,6.dc1ac54.jpg

Jan 01, 2010 | 1993 Pontiac Grand Prix

2 Answers

1990 300zx non turbo has miss on 2 cylinders


dude, i think you have two spark plug cables cross over. go to your local autozone and find a "firing order" if it was a blown head gasket it would show on the compression test but i'm pretty sure its a spark plug cable cross over.

Jun 23, 2009 | 1990 Nissan 300ZX

1 Answer

Need firing order


4 cylinder Fire order = 1342
Distributor rotation = clockwise. good luck

May 27, 2009 | 2000 Dodge Caravan

1 Answer

I fix the head cylinder of my 2004 jetta I can't get it starer


It's possible that while changing the head gasket you inadvertantly change the timing, check to make sure that the #1 cylinder if firing in th proper order,

Apr 10, 2009 | 2004 Volkswagen Jetta

1 Answer

BLOWN HEAD GASKET ON 1997 F250 7.5L


bolt torque speces for 1995 F-250 7.5L camshaft sprocket bolt,harmonic balancer bolt,timing cover bolts and water pump bolts?

Apr 02, 2009 | 1997 Ford F250 SuperCab

2 Answers

95 volvo 940 running rough


Have you checked compression on non firing cylinders? Likely has blown head gasket between these two cylinders if located side by side.

Jun 24, 2008 | 1995 Volvo 940

Not finding what you are looking for?
2000 Jaguar S-Type Logo

263 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Raygin
Raygin

Level 2 Expert

322 Answers

yadayada
yadayada

Level 3 Expert

63801 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...