Question about 1984 Chevrolet Camaro

1 Answer

How do i get my 1984 camaro windsheild wipers off to change them?

I didnt get replacment blades i bought the whole assembley and cant figure out how to get the old ones off please help!

Posted by on

  • Sam Shamblin May 11, 2010

    It would seem that a lot of your problem description is missing. Could you provide more information as to the nature of your problem.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,055 Answers

Drive it too auto zone and they will change them for you free of charge as long as you bought them their

Posted on Feb 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1990 Suburban needs new wipers, I bought the blades, however I dont know how to remove the old ones because it seems to have a different set up. you cant find just blades anymore it comes with the...


The 1990 Chevrolet Suburban has the most common hook-end wiper arms. Locate and press the tab or button where the wiper blade is inserted into the hook of the wiper arm and pull wiper blade out of hook. You may have to rotate and flex the blade to make enough clearance for the hook to pass through.

1990 Chevrolet Suburban Wiper Blade Installation Videos (hook-end arms)

1990 Chevrolet Suburban Wiper Blade Size Options w/Correct Lengths & Attachments

Sep 11, 2011 | 1990 GMC Suburban

1 Answer

The windsheild wippers blades want go down when turned off they stay up in the drivers view?


your wiper motor is bad lost its park position wiper motor has a delay setting which is a micro board and its bad need to replace the wiper motor as a whole. rate this answer if it was helpful comments are welcome. glad to be of assistance.

Nov 24, 2010 | 1990 Ford Probe

1 Answer

Windsheild wiper does not remain in contact for the full stroke.The blade actually raises off the windsheild.1995 volvo wagon. three sets of blades, two sets replaced by mechanics.


Try this:

With ignition on, turn on wiper switch. When wiper arm gets to point where blade does not touch screen, turn off ignition switch so that wipers do not return to park position. It may take a few goes to stop arm in the right position so repeat process until it is in the best position.

Check main wiper arm and bend slightly towards windscreen so that blade touches screen and there is some spring pressure from the arm to keep blade on screen. Also check that there is no interference between main arm and the section which supports the rubber blade. If you get blade chatter as the arm sweeps, twist the end of the main arm slightly in the opposite direction to the movement that produces the chatter. It may take a bit of trial and error to get it all right.

Oct 04, 2010 | Volvo 850 Cars & Trucks

1 Answer

How do you change the windsheild wiper so I can replace it


changing the wipe blades is a tough one. Pick the blade up in one hand. In the center of the blade assembly, underneath, there is a button. You'll need a very small screw driver or something small to press the release. push on the release and pull the wiper blade off.

Jul 06, 2010 | 2005 Chevrolet Silverado

1 Answer

How do I change the windsheild wiper arms?


Hi,
Open the cap at the end of the windshield wiper arm at the cowl of the Blazer. This will reveal the bolt that secures the wiper arm to the wiper linkage. Unbolt the wiper arm using a 3/8-inch ratchet and socket. Place the bolt to the side, as you will reuse it later. Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of work to break it free, but with the right amount of wiggling, it will disengage. Then you can replace the new windsheild wiper arms to it.

Thank you !!

May 26, 2010 | 2001 Chevrolet Blazer

1 Answer

How do you replace the rear windshield wiper blade? I bought a 13" wiper blade but I couldn't figure out how to change it.


like most hatchbacks, you hafta replace the whole rear wiper arm assembly. Go to a Toyota dealers' parts counter.

Jan 16, 2010 | 2005 Scion xA

1 Answer

How to get the old wiper blade assembly off 87 S10 Blazer


With the pin style blades, if you look into the top of the blade at the point were the pin goes through, you will see what looks like a spring or a coil on its side. Use a small screwdriver and push down on that coil at the same time that you try to push the wiper off the pin. I have changed more of these than you can think of, and they are never easy, you have to get things in just the right possition before it will come all the way off. Once you do one the other will come off easier. One word of caution,don't let the wiper arm slip out of your hand and smack the windsheild, it can break it.

Sep 18, 2009 | 1987 Chevrolet S-10 Pickup

1 Answer

Remove and replace wiper blade assebly 89 chevy silverado


there is a keeper on the inside of the arm. its easier to get to if you remove the whole arm. lift the wiper arm and near the pivot point there is a little flat bar that sticks out along the arm itself. its about a quarter inch long. pull that out alittle and slide the arm off the peg. makes it easier for me. if you cannot get the wiper off still, destroy it. your replacing it anyway and the arm is pretty sturdy.

Jun 03, 2009 | 1989 Chevrolet K1500

1 Answer

I have a 1990 Dodge Caravan, and I replaced the windsheild wiper motor and can hear it running, but the wiper blades are still not working; is there anything else that I'm not checking?.....


hi if your can hear it running and all the arms are attatched from the motor to the wiper arm assembley then look at the main arm that comes from the motor where it is bolted on see if its tighted up if so turn your wipers on and watch the main arm nut which is fastened to the motor see if the nut if moving but not the arm as it will be held by splines and these wear off if the nut is not moving and you are sure the motors running then you need to get a new motor

Oct 01, 2008 | Dodge Caravan Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...