Question about 2001 Chevrolet Corvette

2 Answers

Replace turn signal bulbs on 2001 corvette - 2001 Chevrolet Corvette

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Rears are simply remove the two screws on the lens and remove the tail light from the Vette, twist the connector to get to the bulb. Reverse instructions to install. For the fronts jack up the front, remove the small closeout panel under each side, push the brake cooling duct to one side and twist the bulb socket out of the light to get to the bulb. Reverse instructions to install.
sebring1962@yahoo.com

Posted on May 15, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

The rear procedure listed is good, However, the front can be accessed much easier and quicker if you use the procedure stated for the replacement of the 2000 'Vette front directional bulb.
Dave

Posted on Jul 11, 2009

5 Suggested Answers

  • 75 Answers

SOURCE: trying to replace front turn signal in 2001 chevy

to replace the the turn signal and headlamp bulbs, you need to pull the lights out from the front

to do so first you'll have to remove the plastic cover that spans over the radiator (there should be 6 push-in plastic clips holding it in, I use a wire crimping tool, but a couple flat screwdrivers or pliers if careful can work as well)

now, if it's just the cornering lamp that you need, then a large screwdriver or small pry-bar can be used to pop the lamp out

To see where to pry it helps to have a flashlight and look between the headlamp and cornering lamp, there's a clip that holds it in place, just pry against the clip [towards the center of the car, be firm as it is stiff, but if you just yank it, it may brake as it's plastic]

The clip should be around (though below) where the tip of the fender ends. The corner lamp should just pop out with enough prying

For future reference, replacing the headlamp bulbs you get to this point then remove the 2 bolts you can see the brackets the headlamps are mounted to, and they should then come out

Posted on Aug 03, 2010

c17hydro
  • 2984 Answers

SOURCE: how do i change rear turn signal bulb on 89

Rear Turn Signal, Brake and Parking Lights 1984–89 VEHICLES

  1. If removing an inner bulb, remove the license plate. For outer bulb replacement, reach from under the vehicle.
  2. To remove the inner rear brake light, you must reach behind the license place and under the vehicle to access the bulb and socket
  3. Remove the socket from the lens by releasing the locking tab and twisting
  4. Once the bulb and socket are pulled from the rear of the lens, grasp it from behind the license plate opening
  5. Then, pull it out of the side and replace the bulb
  6. Remove the bulb from the socket and replace.
  7. Installation is the reverse of the removal procedure.

Posted on Apr 05, 2009

  • 36 Answers

SOURCE: Left turn signal blinks fast in rear and regular in front

Very simple the bulb is out. When the blinker does that its telling you the bulb needs to be replaced

Posted on May 17, 2009

shocktroop40
  • 155 Answers

SOURCE: front turning light does not work, i replaced the bulb, and when i turn the truning signal does not turn off.

Sounds like you have a bad ground. Follow the wiring harnesses under the hood and in the trunk, there should be a ground wire going to the chassis or to the body. If they are all clean and tight, you might be looking at a bad light socket.

Posted on May 28, 2009

pdbaker6
  • 70 Answers

SOURCE: front turn signal replacement 2001 camaro- cannot get it to seal

take your skirting loose on the bottom side of the bumper and go in that way

Posted on Jun 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

This is on a 2001 Chevy Corvette with 70,000 gentle miles. One or the other of the front daytime running lights (turn signals) keep burning out. The recepticle (connection plugs) looks burned, and the...


this is just a stab in the dark, try cleaning the battery to engine ground and the engine to body(frame) ground, i have a strande geeling that during startup you are getting a voltage spike through the lights

Nov 10, 2010 | 2001 Chevrolet Corvette

1 Answer

How to change the front turn signal on a 2001 corvette


For the 2001 Corvette it's simple for replacing it. Using a Sylvania yellow bulb, part# 3157NA LL or 4157NA LL

Reach inside the air intake opening just below the turn signal and push the black friction-fit hose back and down so it is out of your way. With the fingers of one hand, you can press the top of the black plastic duct (air intake) down to make room for your other hand to squeeze into the opening. Reach inside the hole and locate the wiring harness and lamp socket for the turn signal. The harness is on the bottom of the lamp assembly, so that the bulb is essentially sticking upwards into the reflector housing. Turn 1/4 turn and pull wiring harness out of the opening. Change the bulb and reverse the process. Takes about 4 minutes.

Aug 26, 2010 | 2001 Chevrolet Corvette

1 Answer

JUST BOUGHT 1999 CORVETTE. RIGHT WIDOW DOES NOT


The window is likely due to a worn window motor. The reason the turn signals are flashing fast is due to a burned bulb on the right side. Replace the bulb and that will go away. Let me know if you need anything else.

May 23, 2010 | 1999 Chevrolet Corvette

1 Answer

Turn signals come on but do not blink.


ARE THE FRONT AND REAR TURN SIGNAL INDICATOR BULBS ON STEADY AS WELL?

Sep 29, 2009 | 1972 Chevrolet Corvette

1 Answer

Changing front directioal signal bulb on 2000 corvette need free how to


Turn your ignition on and your headlights. Turn the key off and then the headlights. They should stay open. Open the hood. Remove the rubber 'bump stop' located next to the headlamp on the side that has the bad bulb. Be careful to not change the location of the lock nut.
Now you have a big opening that will allow you to reach down to the rear of the directional signal and remove the socket and bulb by turning counter clockwise. Replace the bulb. I like to put some dielectric compound or at least some vaseline on the base wires of the new bulb.
Test. Reverse procedure for reassembly. Congratulations....... you just saved $70.00!!! Dave

Jul 01, 2009 | 2001 Chevrolet Corvette

1 Answer

Front turning light does not work, i replaced the bulb, and when i turn the truning signal does not turn off.


Sounds like you have a bad ground. Follow the wiring harnesses under the hood and in the trunk, there should be a ground wire going to the chassis or to the body. If they are all clean and tight, you might be looking at a bad light socket.

May 28, 2009 | 1996 Dodge Neon

3 Answers

Left turn signal blinks fast in rear and regular in front


Very simple the bulb is out. When the blinker does that its telling you the bulb needs to be replaced

May 17, 2009 | 2001 Chevrolet Corvette

1 Answer

How do i change rear turn signal bulb on 89 corvette, notmine???


Rear Turn Signal, Brake and Parking Lights 1984–89 VEHICLES
  1. If removing an inner bulb, remove the license plate. For outer bulb replacement, reach from under the vehicle.
  2. To remove the inner rear brake light, you must reach behind the license place and under the vehicle to access the bulb and socket
  3. Remove the socket from the lens by releasing the locking tab and twisting
  4. Once the bulb and socket are pulled from the rear of the lens, grasp it from behind the license plate opening
  5. Then, pull it out of the side and replace the bulb
  6. Remove the bulb from the socket and replace.
  7. Installation is the reverse of the removal procedure.

Apr 05, 2009 | 1989 Chevrolet Corvette

2 Answers

Front turn-signal bulb burned out.


It is a tight squeeze, but you can get your arm down past the headlight to the brake cooling duct and pull the brakeduct off the nose of the car back and to the side. Then you can reach through that hole and replace the turn signal blub

Jun 13, 2008 | 2001 Chevrolet Corvette

Not finding what you are looking for?
2001 Chevrolet Corvette Logo

1,069 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...