Question about 2005 Chrysler Pacifica

Open Question

Trick to remove rear rotor/caliper on '04 Pacifica?

Posted by on

  • Anonymous Apr 03, 2009

    is there any thing special that i have to do to remove my rear roters on 2004 pacifica it feels like a clip or something is holding it on

×

6 Suggested Answers

  • 116 Answers

SOURCE: Rear Rotor removal problem

you have to adjust the parking brake down, using a flat head screwdriver you must turn the starred adjuster wheel counter clockwise to adjsut the parking brake down and allow you to remove the rotor

Posted on Apr 11, 2009

  • 22 Answers

SOURCE: replace rotors 2003 nissan pathfinder

You'll need to remove the wheel bearings then they will come out. It will be the hub/rotor as an assembly once you remove it then you can unbolt the rotor from the back. Once you take the wheel off you'll see the hub cover take that off (its either bolted in or a metal cover you need to pry off with a flat head screw driver and hammer)

Posted on Apr 27, 2009

jmgldsmth
  • 1869 Answers

SOURCE: R&R rotors and calipers on 2005 Ford 500 to do brake job

use a large c-clamp to bottom out the caliper pistons remove the caliper bolts .slip out the pads and remove the caliper from the disk
hang the caliper from a coathanger wire to avoid damaging the brakeline after replacement of the pads;brake bleeding is not needed Rotors are held on to the axle like a wheel; with bolts

Posted on May 29, 2009

fcsr
  • 43 Answers

SOURCE: removing the stereo

These instructions are available at www.carstereohelp.com/strchrysler.htm

Posted on Nov 13, 2008

  • 651 Answers

SOURCE: I need to replace rear break light (driver side) on pacifica 04

if there aren't any screws on the out side, you'll have to gain access from the trunk.

Posted on Dec 03, 2008

  • 335 Answers

SOURCE: Rear rotor on a 2007 chrysler town and country won't budge.

Sounds like you have that old "rust" problem. Rust and calcium build up around the hub and behind the rotor. Wire brush as much as you can around the hub. Using a medium hammer tap the rotor near the hub between the studs. Take care not to hit the studs because this will damage the threads. Sometimes applying some heat with a small butane torch will help free the rotor. Do not heat severely, this will cause warpage. Take your time and you will be successfull. Good luck Moe

Posted on Apr 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much to replace 2006 chrysler pacifica back brake pads


Depends on many factors. 1 Are you doing the labor yourself? 2 Have the bad pads damaged the rotors? 3 Is the axle leaking grease? 4 Is the caliper leaking? 5 Are the calipers stuck? 6 What quality level pads do you want? 7 Are you using the dealer, a good shop, or some "Big Box" store?

Oct 08, 2015 | 2006 Chrysler Pacifica

2 Answers

Brake esemble diagram


Hey Stan the man,need your vehicles info.,year,make,model and engine size and Tommy on the spot here will send you a picture diagram of your rear brake assembly.There's a special spring tool you can get at auto parts store to remove and install springs,me got one.

Oct 15, 2012 | Cars & Trucks

1 Answer

How to replace rear pads on a 2008 Chrysler Pacifica


Pacifica 2006-2008
Brake Calipers

Print I hope this helps,Good luck


Removal & Installation


NOTE Using a brake pedal holding tool, depress the brake pedal past its first inch of travel and hold it in this position. This will isolate the master cylinder from the hydraulic brake system and will not allow brake fluid to drain out of the reservoir while the brake lines are open.

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Negative battery cable Rear wheels Banjo bolt retaining the brake hose to the caliper. Be sure to plug the end of the brake hose or cover it with a plastic bag to prevent contamination from entering the hydraulic system. Caliper guide pin bolts Caliper assembly from the brake adapter by rotating the bottom of the caliper away from the rotor, then lift the caliper with the pads away from the adapter abutment Brake pads by pushing (outboard) or pulling (inboard) from the caliper fingers and piston

    0996b43f80204c0d.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Brake hose banjo fitting (1), caliper guide pin bolt (2), caliper adapter (3), caliper (4), copper seal washers (5) and banjo bolt (6)


To install:
  1. Completely compress the caliper piston
  2. Install or connect the following:
    NOTE The outboard pads are side oriented, make sure the spring clip is installed so it is positioned downwards when the caliper is installed.


    Inboard pad clip against the piston cavity and press the pad until the clip is seated making sure the pad backing plate is flush against the piston


    Outboard pad making sure the locating pins are positioned against the ramps. Slide the pad onto the caliper and ensure the locating pins are squarely seated into the holes on the caliper and the pad is flush against the caliper fingers.
  3. Make sure the abutment shims are in place on both slide abutments.
  4. Retract the caliper guide pins to clear the caliper adapter bosses.

    Brake caliper. Staring with the upper end, position the caliper and shoes over the rotor and align the outboard pad upper edge with the caliper slide abutment. Rotate the lower end of the caliper into position Caliper guide pin bolts and tighten to 200 inch lbs. (23 Nm) Banjo bolt with new washers on each side of the hose fitting and tighten to 35 ft. lbs. (47 Nm) Wheels Negative battery cable
  5. Bleed the brake system and road test the vehicle

Jul 25, 2012 | 2008 Chrysler Pacifica

1 Answer

2008 pacifica how do I remove rear brake pads. The caliper assembly doesn't simply slide out once the attaching bolts are removed.


Pop the pads loose with a screwdriver the caliper comes right off. Took me a few minutes the first time

Dec 16, 2011 | 2005 Chrysler Pacifica

1 Answer

Replace rear brake pads


Rear disc brake pads offer better performance and are not as affected by moisture like conventional brake shoe style brakes are. Rear disc brakes are similar to front disc brakes. The main difference is that rear disc brake systems must incorporate the emergency brake system. There are two methods widely used for the emergency brake with rear disc systems. The first system is a brake shoe inside the brake disc that is actuated by the emergency brake lever. The second is a screw style actuator inside the brake caliper. When activated the brake pads are forced into the brake disc and held tightly by the emergency brake lever.
READ COMPLETELY BEFORE STARTING
Step 1 - Identify Rear Disc Brake Components
rear_brake_pads.jpg Rear disc brake assembly includes; rear brake disc, rear brake pads, brake caliper mount and a caliper mounting screw. (Note: Some vehicles do not have the rotor mounting screw.)
Step 2 - Removing the Rear Brake Caliper Mount Bolts
rear_brake_pads_2.jpg To replace rear brake pads and rotors the rear brake caliper needs to be removed. First loosen the rear brake caliper mount bolts and remove them. Turn counter clockwise.
Step 3 - Lift Rear Brake Caliper from The Caliper Mount
rear_brake_pads_3.jpg After the caliper mount bolts have been removed, gently lift the brake caliper from the caliper mount. Inspect the caliper slides; they should move freely in the caliper mount. Remove rear brake pads and hardware.

Step 4 - Removing Caliper Mount Bolts
rear_brake_pads_4.jpg With a socket wrench or other appropriate removal tool, loosen the rear brake caliper mounting bolts. Remove bolts and lift the caliper mount and remove it from the vehicle. Remove the retaining screw from the disc mounting hole. Tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub holding on tightly, using both hands. You do not want to drop the rotor.

Step 5 - Removing Rear Brake Rotor
rear_brake_rotor.jpg Remove the retaining screw from the disc mounting hole, tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub, hold on using both hands and do not drop.

Step 6 - Install New Brake Rotor
rear_brake_rotor_2.jpg Check the new rotor against the old brake rotor to make sure they are the same size. Clean the mating surface on the wheel hub before the new brake rotor is installed. Reinstall rotor retainer screw.
Step 7 - Reset Rear Brake Caliper
rear_brakes_7.jpg Before new brake pads can be installed, the rear brake caliper must be reset. The reset tool winds the piston back into position so the new brake pads will fit. This style of brake caliper will not compress with a clamp tool; it can only be reset with the proper reset tool.
Step 8 - Reinstall Rear Caliper Mount and Install New Rear Brake Pads
rear_brake_rotor_3.jpg After the caliper has been reset, reinstall caliper mounting bolts and make sure the bolts are tight. Then match up the old brake pads to the new brake pads. They should be exactly the same except, of course; the old ones will be worn out. Check the new brake pads for proper fit and install any brake hardware that is required.
Step 9 - Remount Rear Brake Caliper
rear_brake_rotor_4.jpg Reinstall the brake caliper, align brake pad hardware and reinstall caliper mounting bolts. (Note: align the rear peg of the brake pad to the groove in the caliper piston.) Recheck and retighten all caliper and caliper mount bolts. Bleed brake system to relieve any air in the system. Before driving the vehicle, push the brake pedal down and let it up slowly. This operation forces the brake pads to travel to the brake rotors. DO NOT DRIVE VEHICLE until proper brake pedal operation resumes. When test driving vehicle listen for any unusual noises during the operation of the brakes.
WARNING! Always have the vehicle under inspection on level ground, in park with the emergency brake on. Always wear protective eyewear, gloves and necessary clothing before inspection or work begins. Never crank an engine over when anyone is near the battery or engine. Always have an operational fire extinguisher close by, obey all first aid instructions in the event of an injury. Never stand in front or behind a vehicle when cranked over or running. When engine is cranked over keep hands and clothing away from rotating components. Never move a car without proper brake pedal operation.

Jun 01, 2010 | 1995 Saab 900

1 Answer

What is involved with putting on new rotors


remove tire brake, caliper and secure do not let hang off of brake hose, then remove brake caliper adapter, the rotor. install in reverse order and torque fasteners to specs.

Mar 23, 2010 | 2004 Chrysler Pacifica

1 Answer

How do i replace front pads on 2005 chrysler pacifica


PLEASE DON'T FORGET TO RATE!!!!

Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Front wheels
  3. Place a C-clamp over the caliper as illustrated, place a screw drive head against the outboard pad and hook against the rear of the caliper. Slowly tighten the screw drive and retract the caliper pistons into their bores and breaking the outboard brake pad from the caliper fingers.
  4. Once the pad is free, slide the caliper in on the guides to provide clearance between the rotor and inboard pad.
  5. Place an appropriate prytool through the center opening in the top of the caliper behind the inboard pad between the pistons using care not to contact the piston boots. Pry the pad to free it from the pistons.
  6. Remove the two caliper guide pin bolts and position the caliper aside. Remove the brake pads.
24539c8.gif
Place a C-clamp over the caliper as illustrated

6ccd8b6.gif
View of the caliper guide pins and boots (1), anti-rattle clips (2), brake rotor (3), outboard pad (4), caliper adapter (5) and inboard pad (6)

To install:
  1. Completely compress the caliper pistons
  2. Install or connect the following:
    • Brake pads with anti-rattle clips onto the adapter
    • Caliper and align the guide pin bolt holes with the guide pins. Install the pin bolts and tighten to 32 ft. lbs. (43 Nm).
    • Banjo bolt with new washers on each side of the hose fitting and tighten to 35 ft. lbs. (47 Nm)
    • Wheels
    • Negative battery cable
  3. Check and adjust the brake system fluid level and road test the vehicle.

Nov 01, 2009 | 2005 Chrysler Pacifica

2 Answers

Cant remove wheel hub


here is procedure

Section 04-01: Suspension and Wheel Hubs, Front 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Wheel Hub Bolt Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Refer to Section 04-04 .
  1. Remove disc brake caliper (2B120), and front disc brake rotor (1125). Refer to Section 06-03 .
Brake Shoe and Lining Removal
  1. Remove brake master cylinder filler cap (2162). Check fluid level in brake master cylinder reservoir (2K478). Remove brake fluid until brake master cylinder reservoir is half full. Discard removed fluid.
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Remove wheel and tire assembly from front disc brake rotor mounting face. Use care to avoid damage or interference with disc brake caliper (2B120), front disc brake rotor shield (2K004) or front wheel knuckle (3K185).
  1. Remove rear brake pin retainers (2N386). ( I think it is a T 40 torx bit you need)
  1. NOTE: It is not necessary to disconnect hydraulic connections.

    Lift disc brake caliper from front disc brake caliper anchor plate (2B292) and front disc brake rotor (1125). Do not pry directly against metal caliper piston or damage will occur.
  1. Position disc brake caliper out of the way and support with wire to avoid damaging the disc brake caliper and front brake hose (2078).
  1. Remove outer brake shoe and lining (2001) assembly from front disc brake caliper anchor plate.
  1. Remove inner brake shoe and lining assembly.
  1. Position lug bolt (1107) to clear front wheel knuckle (3K185).
  1. Remove lug bolt from wheel hub (1104).



7548d8f.gif

Installation
  1. Install lug bolt into wheel hub.
  1. Using a lug nut (1012), seat wheel hub bolt into wheel hub.
  1. Install front disc brake rotor and disc brake caliper. Refer to Section 06-03 .
  1. Install wheel and tire assembly. Tighten lug nut to 115-142Nm (85-104 lb-ft).

May 25, 2009 | 1996 Mercury Sable

1 Answer

Rear brake rotor replacment


206-04: Rear Disc Brake 2000 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Disc Removal
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  2. Disconnect the brake hose.
  3. Remove bolt.
  4. Disconnect the rear wheel brake hose (2A442).
  5. Remove the copper washers and plug the brake hose.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc.
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.

Mar 28, 2009 | 2000 Ford Explorer

1 Answer

How to take the front caliber off the 04 expedition


To remove the front caliper, you must pop pop off the anti rattle spring, pay close attention as to how it attaches so you can reinstall it, then pop off the hex bolt covers on the rear of the caliper, then using a 7mm hex driver, loosen the two hex bolts that fasten the caliper to the caliper bracket, and pry the caliper away from the rotor from the bottom first then slide it off.

Dec 06, 2008 | 2001 Ford Expedition

Not finding what you are looking for?
2005 Chrysler Pacifica Logo

Related Topics:

291 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...