Question about 2002 GMC Yukon Denali

1 Answer

Just want to know where you pysically plug in the code reader?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 76 Answers

The obd2 connector should be under the drivers side dash.

Posted on Feb 22, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Loss of power engine hunting when stationary

Hi there,
cars are all electrical these days,
buy a cheap code reader off of eBay ( item no. 361240488837 )
plug it into your diognaustic plug and it will give you a problem code so you know what's wrong with the car,
a booklet comes with the code reader with the codes in it, sometimes it will throw up a code which isn't in the booklet so then you have to google the code, hope this helps :)

Dec 13, 2015 | 2000 Ford Focus

3 Answers

Code reader says 1-3-5 is missing but I know 1&5 is firing jERRY b

Intermittent misses can be caused by bad coils, dirty fuel injectors, and bad o2 sensors, to name a few.

Apr 26, 2015 | 2001 Jeep Grand Cherokee

1 Answer

I need to plug in the code reader

These vehicles are OBDI (OBD one) compliant not ODBII (OBD two). Therefore, the scanner required need to be specific for Chrysler vehicles. The diagnostic connector is located above the driverside inner-fender under the hood. To retrieve codes only, turn the ignition key ON-OFF-ON-OFF-ON and the check engine light will flash the codes.

Dec 15, 2013 | Cars & Trucks

1 Answer

Where do i plug a code reader into for a 1999 vauxhall astra 1.6 8v

see right/left side of the passenger cabin ,below the steering column .you will find a big adopter.

Mar 01, 2012 | Vauxhall Astra Cars & Trucks

1 Answer

How do i use use the onboard dianostics on 2003 impala?

You need to plug an OBDII code reader into the diagnostic port - under dash board near steering column - and then retrieve the codes, using the code reader as per owners manual. The codes can then be read from the OBDII reader and looked up in the manual to see what they refer to. Let me know if this helps. Thanks.

Jan 16, 2011 | 2003 Chevrolet Impala

1 Answer

I have a toyota previa 1991 model I would like to know where the dlc connector is located

if you mean "code reader plug" (sorry not much of a car guy, just know what MY '91 has taught me) is under the drivers seat. there is a lever to lean the seat (whole seat, not just back) back. this is where you add oil, check oil and trans fluid. the code reader plug is the grey box thingy nearest the door.
Hope that helped

Jun 18, 2010 | 1991 Toyota Previa

1 Answer

1997 Jetta - OBD2 Code Reader problem...

encrypted software to stop weekend mechanics?sorry but this is becoming a big problem and the newer the car the bigger the problem

Jun 22, 2009 | 1997 Volkswagen Jetta

1 Answer

Can't read codes with code reader

you most likley have a blown fuse. the fuse for the connector and cig lighter are usually on the same circuit . if you have a owner manuel check and see which fuse is for the obd/cig lighter. if you dont have a manuel then check every fuse in the box and see if you find a blown one. the plug whare the scanner connects is what powers the scanner so if you cant find a blown fuse then you know youre not getting power to the plug for some reason.

Apr 24, 2009 | 2004 Ford F150

1 Answer

Ford code reader won't fit test plugs on my 1990 F250

under dash by steering column past the plastic that covers lower dash and get a code reader .

Dec 31, 2008 | 1990 Ford F250

2 Answers

Dashboard check light stays on

It is a generic indicator that tells the owner/tech that the car has "thrown" a code. You need to retrieve the code with a code reader available from auto parts store, online or at the dealer. Some parts stores lend them out. You find the plug, usually under the dash by the fuse box, plug the reader into it, turn the ignition on, DONT START, and let the reader retrieve the ccodes. Turn off car and read the codes, itll say a code and sometimed itll also tell you what it means, like O2 sensor or misfire or other things. O2 is the most common. Then the reader can reset the light if you plug it back in and tell it to. remember dont start the car wiht the reader plugged in.

May 19, 2008 | 2002 Daewoo Lanos

Not finding what you are looking for?
2002 GMC Yukon Denali Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides