Question about 1998 Ford Explorer

1 Answer

Fuel pump line removal

I can not get the fuel lines off the fuel pump on top of gas tank they sold me a tool thats plastic and fits around line but how does it work

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

It goes around the line itself and you push it into the part where it looks like a spring in it and at same time pull apart while it is in there

Posted on Feb 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How To Drain Fuel Tank On 2005 Jeep Liberty Gas Tank


here is the Cherokee page.
read chapter, 14, page 19 on..
shows all way there, and is not easy.
why do this.
is pressure low
pump dead
is there 12vdc to pump cranking, (no? then dont do this)

http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

i have the KJ pages here. (line # messed up)
Two different procedures may be used to drain fuel
tank: through the fuel fill fitting on tank, or using a
scan tool.
The quickest draining procedure involves removing
the rubber fuel fill hose (7) (Fig. 25) from fuel tank
fitting.
As an alternative procedure, the electric fuel pump
may be activated allowing tank to be drained at fuel
rail connection. Refer to DRB scan tool for fuel pump
activation procedures. Before disconnecting fuel line
at fuel rail, release fuel pressure. Refer to the Fuel
System Pressure Release Procedure for procedures.
Attach end of special test hose tool number 6541,
6539, 6631 or 6923 at fuel rail disconnection (tool
number will depend on model and/or engine application).
Position opposite end of this hose tool to an
approved gasoline draining station. Activate fuel
pump and drain tank until empty.
If electric fuel pump is not operating, fuel must be
drained through fuel fill fitting at tank. Refer to following
procedures.
(1) Release fuel system pressure.
(2) Raise vehicle.
(3) If equipped, remove fuel tank skid plate.
(4) Thoroughly clean area around fuel fill fitting
(6) (Fig. 26) and rubber fuel fill hose (1) at side of
fuel tank. After cleaning, loosen fuel fill hose clamp
(2) at tank.
(5) Before removing rubber hose (1) (Fig. 26) from
fitting, note hose orientation while referring to marks
(3) and (4).
6) Disconnect rubber fuel fill hose at fuel tank fitting
(2) (Fig. 27). Using an approved gas holding
tank, drain fuel tank through this fitting.
Tank Removal
(1) If equipped, remove fuel tank skid plate and
tow hooks. Certain equipment packages will also
require removal of the trailer hitch. Refer to Tow
Hooks, Trailer Hitch or Skid Plate in 23, Body for
removal/installation procedures.
(2) Disconnect and separate fresh air tube (6) (Fig.
28) quick-connect fitting.
(3) Disconnect air tubes at front of NVLD pump
(9) (Fig. 28).
(4) Disconnect NVLD pump (9) (Fig. 28) electrical
connector.
(5) Disconnect fuel pump module electrical connector
jumper. This is located near front of fuel tank.
(6) Support tank with a hydraulic jack.
(7) Remove 4 fuel tank strap bolts (10) (Fig. 28) (2
at front of tank; 2 at rear of tank), and remove both
tank support straps.
(8) Carefully lower tank a few inches.
(9) Continue lowering tank while guiding remaining
hoses and lines through plastic isolator sleeve (3)
(Fig. 29).
(10) If fuel tank is to be replaced, remove NVLD
pump and fuel pump module from tank. Refer to
Fuel Pump Module Removal/Installation procedures.
end , tank out.

why not login to alldata.com and read
or buy the FSM,, and get all pages of chapter 14, end to end.

Oct 19, 2015 | 2005 Jeep Liberty

1 Answer

Need simple fix for my plow truck


Most larger lawn mowers run plastic fuel tanks so look around for a tank that will fit in your tanks space. Have you checked for an after market plastic tank for your machine as the rust problem may have been corrected by the maker of the fuel tanks. Use plastic lines ( suitable for use with fuel-- silicon lines are good but expensive)

Mar 01, 2014 | 1990 Mitsubishi Montero

1 Answer

Where is fuel pump locate


It's in the gas tank. If you've never pulled a tank off to replace a pump, I advise you to buy a Haynes or Chilton repair manual for your Olds to follow the procedure-not immensely difficult, but pretty involved. All lines to the tank removed, electrical plugs disconnected, filler hose removed, then lower and drop the tank-2 straps usually hold it up-(helps to have as little gas as possible in the tank, or it will be quite heavy-in that case, use a floor jack with some wood padding to avoid denting the tank), remove tank away from car. To get to the pump, remove the locking ring (on top of tank) with a brass punch or wooden dowel (so no sparks, see?) or be very careful if you use a steel punch or big screwdriver-NOT RECOMMENDED-but I have done it without sparks, so just be careful. pull the locking ring off and pull out the pump and fuel sender unit. Take off old pump, and replace with new-hopefully it is a OEM-original equipment manufacture-Aftermarket brand pumps just do not perform as well as original (olds) equipment. If the pump has failed, it is good practice to also replace the fuel pump relay-a failing pump can sometimes damage or shorten the life of the fuel pump relay, or so I've heard. Common tools and ratchets are needed for the job-possibly also a release tool for the fuel line fittings-if you have those types of fittings, I think you do, called quick connect fittings.
There's lots of other procedures to get the tank off-like lowering tank, then remove lines and electricals from top of tank, probably the exhaust will have to be lowered, you can siphon gas out the filler neck after lowering the tank a bit. You need to know how to relieve fuel pressure before disconnecting lines, but if little or no gas is in the lines, there won't be pressure. You just need a repair manual to do it step by step-...and label all lines removed, so you know where they go back on the tank.
If I haven't discouraged you yet, buy the manual, and get set for a dirty Saturday afternoon. Essentials like beer and pot are a given. lol.

May 06, 2013 | 1998 Oldsmobile Eighty Eight

1 Answer

How do I dissconnect the fittings on the outside top of 1998 s10 pickup fuel tank for removal to replace the fuel pump.Seems impossible to know how to understand how the fittings work.


the fuel lines on this vehicle are held on by a clip that is just inside the fuel line itself .it is circuler and made of plastic. just past that is a raised ridge that the clip holds onto(you cant see the ridge) if you want to remove the clip their is a special tool that you can buy ( normally come in a set of different sizes) they are fairley cheap . if you dont want to buy the tool you might be able remove the clip by using a screwdriver to pry the clip as evenly as posible all the way around the line( havent tried it myself as i have the disconnect tools .but have been told it can be done. be carefull not to damage the clip

Dec 02, 2010 | 1998 Chevrolet S-10 Pickup

1 Answer

How to change fuel pump?


safely raise and support the back of the vehicle. The fuel pump will be on the passenger side of the fuel tank.

remove the fuel lines from the pump. Be careful as any residual pressure in the lines will spray out and get you. Wrap a rag around the connector before you remove it to reduce the spray.

Unbolt the passenger side fuel tank strap. You will need to do this to remove the wiring harness to the pump.

Remove the 6 bolts holding the pump to the fuel tank. An 8mm socket should work. If the tank is full gas will start coming out at this point. Have a drain pan ready to catch it.

Pull the pump out of the tank. This can be a bit of a rubix cube but the pump will come out without having to pull or drop the tank.

Please be careful! anytime there is fuel vapor or spilt fuel there is the chance for fire.

Use new clips in the fuel line fittings. There should be one black clip and one white clip. They only go into the fitting with the tab facing the line. If you put them in backwards the lines will pull off.

Sometimes they use a quick connect fitting that a release tool needs to be used to get the fittings off of the fuel pump. They can be purchased at any good auto parts store. There are two sizes and most parts stores will carry the tool that has both sizes in one tool.

Make sure you replace the fuel filter when replacing the pump.

Oct 20, 2010 | 2002 Ford Crown Victoria

1 Answer

2003 5.3L Chevy Tahoe. The fuel pump needs replaced


The connectors tend to get dirt and debris in where the special tool slides in which prevents the little tabs from disengaging from the raised ring on the plastic pipe. Pull the line towards the pump as if you were trying to push it on even further and use compressed air to blow out any crud where the tool goes. Then insert the tool and push it in firmly while pulling the line toward the tool a bit to relieve the pressure on the little internal metal retaining clips and at that point with a little wiggling the line should come off. I've taken off dozens and they can be exasperating to say the least. IF all else fails and you are certain that you are going to replace the pump module and absolutely can not get the lines disconnected for the stubby plastic fittings on top of the old one then you could simply break off the plastic fittings on the old pump so you can work on getting the fittings disconnected once you have the tank out. I've had to do this a couple of times but it means that the old pump module can't be used again since the fittings would be broken off of it. Be extremely careful working around the tank as it will be full of gasoline fumes and extremely flammable!

Jun 11, 2010 | 2003 Chevrolet Tahoe

3 Answers

How to remove fuel pump on Neon 1998 ? can I reach from inside the vehicle ?


on a dodge neon the fuel pump is in the SIDE of the tank... NOT the top. to remove the pump follow these steps...
******* first unplug battery and remove ********
1. unbolt passenger side tank strap and lower side of tank.
2. a. if tank is plastic, CAREFULLY unscrew plastic retainer ring but do NOT remove.
b. if metal tank, unscrew metal retainer flange but do NOT remove
3. unplug electrical connector and fuel line from pump. move aside.
4. completely remove retainer BE CAREFUL not to disturb pump.
5. have drain pan or wide-shallow bucket available to collect gas. (if tank is full this will need to be able to hold 7-8 gallons)
6. gently twist and pull pump out till gas comes fourth. catch gas in pan/bucket.
7. remove pump when gas stops flowing.
8. install is reverse of removal.
9 BE CAREFUL not to wrinkle gasket or lose gasket into tank when installing or the tank will leak around pump.
10. tighten retainer but DO NOT OVER TIGHTEN.
11. reconnect plug and fuel lines check for leaks.
12. reattach tank strap and fasten
13. refill tank with clean gas. check for leaks.
14. put battery back in. connect battery, start your neon and check for leaks one last time.
15, have fun. this will take about 4hrs to do by yourself with proper tools.

Apr 24, 2010 | 1998 Dodge Neon

2 Answers

Need directions on replacing 2000 dodge durange 4.7 ltr fuel pump


WHAT YOU WILL NEED TO DO FIRST IS JACK THE TRUCK UP AS HIGH AS SAFELY POSSIBLE.. BE SURE TO USE JACK STANDS THAT WAY THE TRUCK DOENT FALL OVER.. ONCE UP IN THE AIR HE WILL NEED TO TAKE THE GAS TANK OUT OF THE TRUCK.. THERE ARE TWO STRIPS HOLDING THE TANK INTO PLACE..THEN WHEN HE GETS THE TANK ON THE GROUND, REMOVE ALL THE FUEL LINES.(THERE ARE CLIPS ON THE PLASTIC LINES BE EASY) THEN WHEN HE GETS THE LINES LOOSE, THERE IS A METAL RING ON THE TOP ON THE FUEL TANK..HE CAN USE A SCREW DRIVER TO GET THE RING OFF( HE WILL SEE HOW TO TAKE IT OFF WHEN HE LOOKS AT IT) WHEN THE RING IS OFF PULL THE FUEL PUMP ASSEMBLY OUT OF THE TANK AND REPLACE THE FUEL PUMP (THE WHOLE FUEL PUMP WILL JUST NEED PULLED OUT, NO SCREWS) ..JUST REPEAT THESE STEPS BACKWARDS TO REINSTALL .. THIS SHOULD SOLVE YOUR $700 PROBLEM..GOOD LUCK AND THANKS FOR USING FIXYA.COM...KEITH..

Mar 14, 2009 | 2000 Dodge Durango

2 Answers

1999 jeep cherokee do you have to remove the fuel pump to replace


The combination Fuel Filter/Fuel Pressure Regulator is located on the fuel pump module. The fuel pump module is located on top of fuel tank.

The filter/regulator may be removed without removing fuel pump module although fuel tank must be removed.

REMOVAL
  1. Remove fuel tank. Refer to Fuel Tank Removal/Installation.
  2. Clean area around filter/regulator.
  3. Disconnect fuel line at filter/regulator. Refer to Quick-Connect Fittings for procedures.
  4. Remove retainer clamp from top of filter/regulator. Clamp snaps to tabs on pump module. Discard old clamp.
  5. Pry filter/regulator from top of pump module with 2 screwdrivers. Unit is snapped into module
  6. Discard gasket below filter/regulator.
    1. Before discarding filter/regulator assembly, inspect assembly to verify that O-rings are intact. If the smallest of the two O-rings can not be found on bottom of filter/regulator, it may be necessary to remove it from the fuel inlet passage in fuel pump module.
    INSTALLATION
    1. Clean recessed area in pump module where filter/regulator is to be installed.
    2. Obtain new filter/regulator (two new O-rings should already be installed)
    3. Apply a small amount of clean engine oil to O-rings. Do not install O-rings separately into fuel pump module. They will be damaged when installing filter/regulator.
    4. Install new gasket to top of fuel pump module.
    5. Press new filter/regulator into top of pump module until it snaps into position (a positive click must be heard or felt).
    6. The arrow molded into top of fuel pump module should be pointed towards front of vehicle (12 O'clock position).
    7. Rotate filter/regulator until fuel supply tube (fitting) is pointed towards front of vehicle (12 O'clock position).
    8. Install new retainer clamp (clamp snaps over top of filter/regulator and locks to flanges on pump module).
    9. Connect fuel line at filter/regulator. Refer to Quick-Connect Fittings for procedures.
    10. Install fuel tank. Refer to Fuel Tank Removal/Installation.
WARNING: THE FUEL SYSTEM IS UNDER CONSTANT FUEL PRESSURE EVEN WITH THE ENGINE OFF. THIS PRESSURE MUST BE RELEASED BEFORE SERVICING FUEL TANK .

Two different procedures may be used to drain fuel tank (lowering tank or using DRB scan tool).

The quickest draining procedure involves lowering the fuel tank.

As an alternative procedure, the electric fuel pump may be activated allowing tank to be drained at fuel rail connection. Refer to DRB scan tool for fuel pump activation procedures. Before disconnecting fuel line at fuel rail, release fuel pressure. Refer to the Fuel System Pressure Release Procedure for procedures. Attach end of special test hose tool number 6541, 6539, 6631 or 6923 at fuel rail disconnection (tool number will depend on model and/or engine application). Position opposite end of this hose tool to an approved gasoline draining station. Activate fuel pump and drain tank until empty.

If electric fuel pump is not operating, tank must be lowered for fuel draining. Refer to following procedures.

FUEL TANK REMOVAL
  1. Disconnect negative battery cable at battery.
  2. Release fuel system pressure. Refer to the Fuel System Pressure Release.
  3. Raise and support vehicle.
  4. If Equipped: Remove fuel tank skid plate.
  5. Remove 4 fuel hose shield mounting bolts and remove fuel hose shield from body.
    1. Remove fuel tank fill hose and vent hose clamps at fuel tank filler tube. Remove both hoses at fuel filler tube.
    2. Remove exhaust tailpipe heat shield mounting bolts and remove shield. CAUTION: To protect fuel tank from exhaust heat, this shield must reinstalled after tank installation.
    3. Place a hydraulic jack to bottom of fuel tank. WARNING: PLACE A SHOP TOWEL AROUND FUEL LINES TO CATCH ANY EXCESS FUEL .
      1. Disconnect fuel supply line from fuel extension line near front of fuel tank. Refer to Fuel Tubes/Lines/Hoses and Clamps. Also refer to Quick-Connect Fittings for procedures.
      2. Disconnect EVAP canister vent line near front of tank.
      3. Disconnect fuel pump module electrical connector (pigtail harness) near front of tank. Harness connector is clipped to body.
        1. Remove two fuel tank strap nuts. Position both tank support straps away from tank.
        2. Carefully lower right side of tank while feeding both fuel hoses through access hole in body. Fuel Tank Full And Not Drained Using DRB Scan Tool: To prevent fuel loss through hoses, keep left side of tank higher than right side while lowering. Do not allow hose openings to drop lower than top of tank.
        3. Continue lowering tank until clear of vehicle. Place tank on floor with left side (hose side) higher than right side
          1. Drain tank by removing fuel fill hose at tank. Fuel fill hose is largest of 2 hoses. Insert the drain hose (from an approved gasoline draining station) into hose opening. Drain tank until empty.
          2. If fuel pump module removal is necessary, refer to Fuel Pump Module Removal/installation for procedures.
          INSTALLATION
          1. If fuel pump module is being installed, refer to Fuel Pump Module Removal/installation for procedures.
          2. Install fuel fill/vent hoses to tank fittings. To prevent hose from kinking, rotate each hose until index mark on hose is aligned to index tang on fuel tank.
          3. Install hose clamps to hoses. Position clamps between index marks on each hose.
          4. Position fuel tank to hydraulic jack.
          5. Raise tank into position while guiding fuel fill and vent hoses into and through access hole in body.
          6. Continue raising tank until positioned to body.
          7. Attach two fuel tank mounting straps and mounting nuts. Tighten nuts to 10 Nm (90 in. lbs.) torque. Do not over tighten nuts.
          8. Install both fuel hoses to fuel fill tube. Tighten both retaining clamps.
          9. Position fuel hose shield to body. Install and tighten 4 mounting bolts.
          10. Connect fuel pump module pigtail harness electrical connector near front of tank.
          11. Connect fuel pump module supply line near front of tank. Refer to Quick-Connect Fittings for procedures.
          12. Connect EVAP hose near front of tank.
          13. Install exhaust tailpipe heat shield.
          1. Install fuel tank skid plate (if equipped).
          1. Lower vehicle and connect battery cable to battery.

Feb 08, 2009 | 1999 Jeep Cherokee

1 Answer

Fuel pump hose fittings


is there plastic clips that hold the lines if there is not there is a tool that you put in the end of the line that releases the line

Dec 14, 2008 | 1998 Chevrolet K1500

Not finding what you are looking for?
1998 Ford Explorer Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...