Question about 1999 Mazda 626

1 Answer

97 mazda 626 v-6 some times car will start other times it dont fire at all when warm or cold when running it runs good

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 158 Answers

Hello if you car doesnt want to stat all the time,then the next time it dosent hold up on the ignition switch and turn the key. If it does then you have a switch problem.This is common in the mazda 626

Posted on Feb 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 mazda 626 cranking over but not firing problem:


Good Morning, those are good little cars, they are the sister car to the ford probe. Most of the problems with those when they are not getting any spark is related to the distributor and the electronics within breaking down with age. Whether it is a 4 cylinder or a 6 cylinder that is where I would start first is trying my local salvage yard for a good one and putting it in its place. With all the ones we have had over the years 97% has been the same thing.

Oct 23, 2010 | 1994 Mazda 626

1 Answer

My 2001 626 is slow to start when cold. Battery is new and it cranks fine, just takes about 15-20 seconds of cranking before it fires off. Car starts normally when warm and we have tried several types of...


It could be that you have picked up a batch of dirty fuel that has clogged the gauze input filter that is part of the fuel pump inside the fuel tank.

Jul 29, 2010 | 2000 Mazda 626

1 Answer

Bad hot starting


he may need to replace the ignition coil... when its hot it gets faulty its more likely to give a bad run then you have to wait for it to get cold to have a good run

Jan 30, 2010 | 1999 Mazda 626

1 Answer

'95 Mazda 626 LX 6cyc - Heat is spuradic...I notice the temp gage will spike and then the heat will get warm and it will return to the normal range?


You have air in your cooling system. Fill your cooling system when the car is cold. First check the radiator if it has a cap, fill that first, replacethe cap tightly, then fill the overflow tank to the indicated level. Start it and turn the heater to the full hot position. Let it run untill it reaches opperating temperature. Quickly squeezing the upper radiator hose 3 or 4 times every now and then to "burp" the system. look for leaks. If this does not solve the problem you may possibly have a headgasket leak.

Dec 17, 2009 | 1995 Mazda 626

1 Answer

97 model 626 will run fine then when warm will not start is getting feul and has good spark


Your problem is either lack of compression which is due to piston rings worn and having more than 4thou per inch per bore which when cold compression could be 100PSI but when the engine gets hot and expands and all metal parts do then compression could be down to 85 to 90 psi and you havent enough **** to **** in the fuel to burn and run, OR the engines is getting to hot . or the head gasket might be blowing slight compression into the cooling system which will cause the same.
Let me know more information about the problem Ron

Oct 20, 2009 | 1997 Mazda 626

1 Answer

Mazda 626 six cyl runs ok for 20mins then misfires and runs rough


check the belt timing. could be firing early or late.

Apr 30, 2009 | 1995 Mazda 626

1 Answer

My new 94 mazda 626 2.0 is very hard starting


tap on the gas a couple of times then try to start it.

Apr 28, 2009 | 1994 Mazda 626

2 Answers

Mazda 626 timing


If the timing was 180 out it wouldn't run at all.
Do a compression test to make sure all the cylinders are in good condition, go back over your timing and make sure you aren't overlooking something like two plug leads swapped?, it sounds like it's only firing on two.

Aug 17, 2008 | 1996 Mazda 626

4 Answers

Mazda 626 engine cut off when excel over 3000 rmp


my 1988 mazda 626 starts okay then dies everytime it idles down to normal idle speed. i replaced the throttle control sensor and the mass air sensor. i replaced the rotor in the distributor but is still dies. if you throttle up to about 1500 rpm it keeps running. any ideas???

Aug 04, 2008 | 1994 Mazda 626

Not finding what you are looking for?
1999 Mazda 626 Logo

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...