Question about 1993 Nissan Altima

2 Answers

What tools need to change starter 1993 nissan altima

What size sockets or anything else do i need

Posted by on


2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 1,596 Answers

A Basic METRIC Socket set AND Combo Wrench set Will Do The JOB

Posted on Feb 21, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I cant start my 93 nissan altima all i hear is clicking

Posted on Jul 15, 2012


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What are the tools I need to change my starter on a 2006 Nissan Altima

A screwdriver, rachet, an extension, and 8,10,12, and 14 MM sockets.

Dec 20, 2016 | 2006 Nissan Altima

1 Answer

I need to know what tools are needed to change the starter

a socket set from size 6mm to at least 16mm and a ratchet honestly i think that is all that is required. the small socket size will be for disconecting wires. the bigger size socket will be used to take the mounting bolts off. you might need a philips head screw driver or a flat head screw driver I am not entirely sure because almost every veicle is different but some sockets a ratchet and maby a screw driver should be all you need. i hope this helps and if it doesnt i am sorry. be carefull and have a nice day!

Dec 23, 2011 | 1993 Suzuki Sidekick

1 Answer

What are the steps in changing all 3 belts on my 1993 Nissan Pathfinder 2WD? What tools and socket sizes will I need?

Go to and punch in your yr/mk/model of car and you will be able to view an online Chiltons manual for free.

Jun 25, 2010 | 1993 Nissan Pathfinder

1 Answer

Where is 97 Nissan Altima starter

The starter is located between the engine and the firewall. Behind the engine. The easy way to get to it is by going underneath the car. Make sure you do this safely using jack stands and wheel blocks. The starter is bolted to the transmission housing.

Feb 13, 2010 | 1993 Nissan Altima

1 Answer

Where is the starter relay for a 1993 Nissan

the car had only theft warning relay location on the front right fender check fuse link location on the front left side fender

Dec 14, 2009 | 1993 Nissan Altima

1 Answer

Howm do I replace a starter on a 1995 Nissan

Nissan 240SX/Altima 1993-1998 Repair Guide

(see Figures 1, 2 and 3)

Fig. 1: The starter is located to the left of the oil filter housing on the engine block

Fig. 2: The starter motor is removed from the bottom side of the engine compartment

Fig. 3: When installing, be sure to align the starter's mounting bolt holes with those in the engine block
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. Remove the starter support bracket, as required.
  4. Label and disconnect the starter electrical harness.
  5. Support the starter from beneath the vehicle using a jackstand.
  6. Remove the starter mounting bolts.
  7. Carefully lower the starter from the vehicle.
To install:
  1. Position the starter on the engine and support it using a jackstand.
  2. Install the starter mounting bolts and tighten to 30-37 ft. lbs. (40-50 Nm).
  3. Connect the starter electrical harness.
  4. Install the starter support bracket, as required.
  5. Lower the vehicle.
  6. Connect the negative battery cable.

Hope helped with this (remember rated this help) Good luck.

Nov 27, 2009 | 1995 Nissan Altima

1 Answer

How to change the frt side marker lights on a 1993 nissan altima

Front upper signal lights are attached to the vehicle by a single screw.
After the screw is removed, carefully pull forward and out.
Remove the socket by twisting counterclockwise, then depress and twist the bulb 1/8 turn

Mar 23, 2009 | 1993 Nissan Altima

1 Answer

How do losen belt on 20003 Nissan Altima?

you need to go rent a serpintine belt removal tool form autozone, it is a long pole with a socket or wrench end, and it will aloow you to loosen the tensioner pulley....

Nov 05, 2008 | 2003 Nissan Altima

1 Answer

I need to change an axle in a 1993 nissan altima

the axle nut should be a 36mm
will also need a 17mm to remove three bolts holding ball joint to control arm and a pry bar to pop axle out of transmission. if replacing right side will need tounhook support bearing

Oct 10, 2008 | 1993 Nissan Altima

Not finding what you are looking for?
1993 Nissan Altima Logo

236 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

77194 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides