Question about 2001 BMW Z3

1 Answer

How do you replace the waterpump on a bmw z3 2.2

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,596 Answers

3.0 Coupe

Removing and installing complete water pump (M52 / S52 /M52TU/ M54 / M56)

Remove alternator
drive belt, refer to Engine, Cooling and Exhaust - Engine - Drive Belts, Mounts, Brackets and Accessories - Drive Belt - Service and Repair - Procedures See: Engine\Drive Belt\Service and Repair
Note: M52/S52 The water drain plug is located on the exhaust side between cylinders 4 and 5 in the engine block (illustration).
M52TU / M54 / M56 The water drain plug is located on the exhaust side on cylinder 2 in the engine block.
Drain and dispose of coolant.

Installation:
Replace seal.
Tightening Torque, refer to Specifications - Mechanical. See: Specifications
Vent cooling system and check for leaks, refer to Engine, Cooling and Exhaust - Cooling System - Service and Repair - Procedures. See: Service and Repair
Release belt pulley,Release water pump.,Tighten two screws (M6) into thread of water pump and water pump out of timing case.

Installation:
Replace O-ring and coat with coolant as anti-friction agent.

2.5L Roadster
SAME PROCEDURE FOR PICTURES Email Me @ aol.com

Posted on Feb 21, 2009

3 Suggested Answers

  • 117 Answers

SOURCE: Will the wheels from a BMW Z3 M fit a 1999 BMW Z3 2.8 ltr roadster?

yes they will you just may need to use a wheel spacer

Posted on Jul 01, 2008

  • 1 Answer

SOURCE: replaced water pump in 2001 bmw z3 and now car won't start

I would suspect that you pulled a wire off when you were installing the water pump. Check to see if you have spark

Posted on Feb 20, 2010

T0Max
  • 32 Answers

SOURCE: How do you replace the hood badge? 98 BMW Z3

Allow some warm water mixed with dish soap to penetrate around the edges of the old ornament. Gently slide a pry tool into the top or bottom center. The hold downs (plastic clips that SHOULD pop) are going to be on the left/right middle. While continuing to pour some warm water and dish soap around the pry point, work the pry tool around the circle. If you don't have a pry tool, use a non-ridged butterknife wrapped in electrical tape. It will take some force to remove, but it will come out.

Please note, you CANNOT re-use the clips. Your new hood ornament should have some with it.

Remove ALL old adhesive from the paint surface so that the new ornament will go on smoothly. Best of luck!

Posted on Apr 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bmw 316i e36 when idol car doesnot overheat but after driving for about 2km car starts overheating


Have you checked your coolant levels as well as thermostat and waterpump functions? These can all atribute to engine overheating.

Jul 12, 2011 | 1997 BMW 318

1 Answer

I wanna know how to replace a water pump on my 1998 BMW 528i


You need to drain radiator, pull fan shroud, pull fan/fan clutch, reeve belts and pulley then unbolt waterpump. You do beed special tools for fan clutch and pulley removal. BavAuto.com or Pelican parts .com have parts, tools and good info on how to do the job successfully.

Mar 31, 2011 | 2000 BMW 5 Series

1 Answer

I have a 1993 BMW 325i, I am having cooling in which the car overheats profusely when running for a little while. I just replaced the thermostat and I am getting ready to go check the waterpump to see if...


U may have a faulty fan clutch,If the fan is turning very slowly while the engine is running its faulty.Also you may have a restriction in the radiator,one way to check the radiator is to remove the hoses and flush water through it to see if it flows straight through.A common issue is the fan clutch be sure to check it first.

Feb 03, 2010 | 1993 BMW 3 Series

2 Answers

1998 bmw overheating at times has had the waterpump


This is typical of BMW 318 and others I suppose.
If after changing the radiator, the hoses, the water pump then the other cause is leakage of coolant at the back of the engine block.

This is hidden but there is a hard plastic outlet which gives away after 5 or more years. If the leakage is serious you can notice the coolant disappearing very fast.

Worse it could be the gasket leaking.

Oct 26, 2009 | 1999 BMW 318 ti

1 Answer

1991 bmw 318is 4 door 16 valve motor, runs hot and radiator cold


you may have bad waterpump,the impeller on pump may be borken, just because it doesnt leak doesnt mean its good.also could have exhaust entering cooling system (bad headgasket) if pump is good have a block test done.

Sep 29, 2009 | BMW 318 Cars & Trucks

1 Answer

Remove waterpump/ fan


go to www.autozone.com you can view repair manuals there

Mar 28, 2009 | 1996 BMW 318

1 Answer

Thermostat location


you didn't mention what size engine you have, so i assumed its a 1.8L. thermostat is located at the housing just above the waterpump on the front of the engine. its #5 in the attached link http://www.realoem.com/bmw/showparts.do?model=CJ11&mospid=48077&btnr=11_1393&hg=11&fg=35

Jan 27, 2009 | 1997 BMW Z3 Roadster

1 Answer

1995 740il bmw


look under the hood.... or up at the underside of the hood.... there should be a sticker with the serpentine belt routing.

Robert

Jul 17, 2008 | 1995 BMW 7 Series

Not finding what you are looking for?
2001 BMW Z3 Logo

1,644 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Fred Sops

Level 2 Expert

271 Answers

Al Clark

Level 2 Expert

290 Answers

Doberman

Level 2 Expert

246 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...