Question about 1984 Chevrolet K1500

1 Answer

Ignition removal process for 1984 chevy 1/2 ton

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,596 Answers

This Outlines Removal Of Both LOCK CYLINDER<< Mechanical)) And The Ignition SWITCH ITSELF<< ELECTRICAL))

  1. Remove steering wheel as outlined previously.
  2. Remove turn signal switch as outlined in ``Turn Signal Switch, Replace'' procedure.
  3. Place ignition switch in ``Run'' position, then remove lock cylinder retaining screw and lock cylinder.
  4. To install, rotate lock cylinder to stop, while holding housing as shown, Fig. 6. Align cylinder key with keyway in housing, then push lock cylinder assembly into housing until fully seated.
  5. Install lock cylinder retaining screw. Torque screw to 40 inch lbs. for standard columns, or 22 inch lbs. for adjustable columns.
  6. Install buzzer switch, turn signal switch and steering wheel


CABALLERO, EL CAMINO, C, K, R, V & 1986---87 G MODELS
The ignition switch is mounted on top of the mast jacket inside the brake pedal support and is actuated by a rod and rack assembly.
  1. Disconnect battery ground cable.
  2. Disconnect and lower steering column. On some models, it may be necessary to remove the upper column mounting bracket if it hinders servicing of switch. Use extreme care when lowering steering column to prevent damage to column assembly. Only lower steering column a sufficient distance to perform ignition switch service.
  3. On Caballero and El Camino, rotate ignition lock to ``Off'' unlocked position.
  4. On C, K, R and V models, rotate ignition lock to ``Off'' locked position.
  5. If lock cylinder has been removed, pull switch actuator rod up to stop, then pushrod down to second (Caballero or El Camino) or first (C, K, R and V models) detent as shown, Fig. 7.
  6. Remove column mounted dimmer switch, if equipped, then remove switch retaining screws and switch.
  7. Reverse procedure to install, noting the following:
    1. Place gear shift lever in neutral.
    2. Place lock cylinder and switch in positions noted in steps 3 and 4.
    3. Fit actuator rod into hole in switch slider and secure switch with retaining screws, ensuring switch does not move out of detent.
    4. Install and adjust dimmer switch, if equipped, as outlined in ``Column Mounted Dimmer Switch, Replace'' procedure.
    5. Torque retaining screws to 35 inch lbs., then check switch operation.

Posted on Feb 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a diagram of 1999 chevy 1/2 ton 4x4 rear brake brackets


Go to you nearest auto part. Store. They will print one up for you or when you get the kit it will diagram with it

Mar 06, 2013 | 1994 Chevrolet K1500

1 Answer

Wiring diagram for distributor on 1984 chevy k10 1/2 ton


i need a diagram for putting back together a steering column in a 1984 chevy

Jan 15, 2012 | Cars & Trucks

1 Answer

How to remove the wiper switch in a 1984 chevy truck


Remove dash bezel . Remove plug from switch itself. Remove screws holding switch in place. Repeat process to re-assemble.

Mar 15, 2011 | 1984 Chevrolet Chevy

1 Answer

How to remove and replace the ignition switch cylinder in a 1976 chevy cheyenne 1/2 ton pickup?


Remove the horn button, nut the pull the wheel off with a puller.Remove the lock plate retaining spring using a Lock plate press. Remove the directional switch screws (3).. Lift that switch out of the way to remove the ignition lock screww
Pull out ign Lock Cylinder

Reverse this procedure to install

Jun 02, 2010 | 1977 Chevrolet Silverado 2500

1 Answer

My head lights only work when i keep the starter ingaged, also not charging. new alt batt and starter. 1984 chevy 3/4 ton


Replace the ignition switch,it only has aux.out put power in start position,not in the run position.

Jan 03, 2010 | 1984 Chevrolet C1500

2 Answers

84 chevy 4 wheel drive auto hub removial


Remove the cap,look close and you vill see a snap ring inside the ¨pipe¨ take out the ring and then you should be able to pull out the hub.

Jan 06, 2009 | 1984 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

1,976 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...