Question about 2003 Subaru Baja
How do I remove the hardware for replacing the headlights on a Subaru Legacy 2003
If your just trying to replace the bulbs you'll have to twist the grey cover on the back side of the head lamp lens assembly either clockwise or counter. they are usually very hard to turn because they have a water tight sealing O-ring that your turning against. But, it is much easier to turn the drivers' side if you remove the battery, I recommend it. Once you have the covers off you will see the back of the bulb being held in by a little wire hold-down, you can unhinge it just like a safety pin(push it in,down,& let it spring it's self out and away from the bulb). Then just pull on the white wire to free the bulb, DO NOT TOUCH the new bulb glass with your fingers cuz the oils will cause the bulb to explode once the bulb is turned on. Then just install in reverse order in which you removed it all. Sometimes the simplest actions take the most complex explinations, don't they? Hope this is what you were asking about, & I hope it helps...
Posted on Aug 09, 2009
These are easy. for the passenger side you will need to remove the two clips that hold the duct onto the front grill. once these are removed you will be able to pull this off and get it out of your way. now you will see a gray round plastic cover with wires coming out of it. just turn it in the direction indicated for removal. Now just disconnect the bulb and clip and replace the bulb. On the driver side you will need to pull the clip that holds the washer fluid neck filler and get this out of your way to access the drivers side bulb. These bulbs are around 22 dollars and dual bulbs meaning they are the low beam and the high beam in one.
Posted on Jun 26, 2009
If your havinf any trouble I suggest you can pick up a repair manual from any part store and if you feel like spending around $26 you can get alldata online for you car for a year I just did it for some wiring diagrams and it helped me out bigtime good luck
Posted on Mar 27, 2009
We have the 05 2.5i with cloth interior. Here is your answer which I'm quoting from the LEGACYGT.COM web site: "at the front of the seat, pull up towards the ceiling, then forward"......Here is the web address of the relevant thread/posts: http://legacygt.com/forums/showthread.php?t=13578
Posted on Oct 18, 2009
the fuel pump is located in the fuel tank, that tank must be pulled to do this. the procedure for removing the tank and pump are very little changed from car to car, here are a good set of general instructions with photos.
Posted on Nov 12, 2009
yes that is correct, remove glovebox , metal bracket in front ( mark which way round this bracket goes it will go back wrong and glove box wont fit ) , unplug electrical plug from heater motor, unscrew 3 bolts/screws from motor replace in reverse..30 min tops..
Posted on Nov 15, 2009
This is correct except your dont need to loosen any screws, at on my 03 galant you dont. The wire clip is a spring clip and just need to be unclipped and it will swing out of the way.
Posted on Aug 22, 2010
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Nov 30, 2014 | 1995 Subaru Legacy
Jul 06, 2012 | 1997 Subaru Legacy
Apr 24, 2012 | 2003 Subaru Legacy
Nov 30, 2011 | 1997 Subaru Legacy
Aug 15, 2010 | 1998 Subaru Legacy
Mar 31, 2010 | 1995 Subaru Legacy
Dec 18, 2008 | 1998 Subaru Legacy
Oct 19, 2008 | 1999 Subaru Legacy
1,541 people viewed this question
Usually answered in minutes!