Question about 2000 Chevrolet Camaro

1 Answer

Turn signals on my 2000 camaro dont blink - 2000 Chevrolet Camaro

Posted by on

  • Anonymous Apr 23, 2009

    where is the flasher



1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

This is most likely a problem with your flasher. The turn signals and four-ways operates using a flasher that connects and disconnects the circuit rapidly creating the on-off effect. When these go bad the the wire inside can get weak and no longer had enough heat to pull the bridge off. Also this will most likely be located within the interior fuse panel. Hope this works.

Posted on Mar 10, 2009

  • waynejenkins Oct 15, 2010

    It is clipped on the panel behind the drivers door fuse panel. If you pull the headlamp switch bezel you can look down behind it and see where it is clipped on, and reach under the dash and see the edge of the clip where it over hangs.



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Right turn signal dont blink. replaced flasher still eont blink.

if the flasher is bad, then both sides will not work. you have a bad bulb in the system, you must track it down. note there is more than just one bulb in front and one in back, the side markers blink also so you must check them all. take a bulb out and put 12 volts to it from the battery.

Mar 16, 2011 | 1997 Chevrolet Camaro

1 Answer

Can't find turn signal flasher on 2000 chevy camaro

look on driver side at the fire wall if not their look undash driver side .look undash for both places.

Dec 11, 2010 | 2000 Chevrolet Camaro

1 Answer

My 1984 camaro turn signal lights dont blink but are lit. Also, when i turn my lights on, my tachometer, oil pressure and temperature gauge stop working.

The turn signals use a small relay for the flash, it's located in the interior fuse panel under the dash (small metal/plastic can)'s the only thing in the fuse panel that's not a fuse.

They're a few dollars at Autozone and easy to replace.

The short/overload killing the dash gauges will be a bit harder to troubleshoot...Do the gauges die with the parking lights, or only after the switch is all the way out to headlights?

Apr 01, 2010 | 1984 Chevrolet Camaro

1 Answer

My turn signals wont blink. What do i need to do to get them to start blinking? they turn on in the back, but they just dont blink.

the blinker rewlay went bad im not sure where it is in your car but most likely near the fuses itll be a black box either square or cylindrical

Jul 09, 2009 | 1997 Chevrolet Camaro

1 Answer

My hazards in my 1997 camaro rs work, but the back and front turn signals dont. The lights for the signals dont work in the dash either, just the lights for the hazards

check the signal flasher ( little silver or colored can in fuse panel or under dash. 4 ways have 1 flasher and the signals have a seperate flasher. Put hazards on to hear click, to determine which flasher is which. Hope this helps

Apr 13, 2009 | 1997 Chevrolet Camaro

2 Answers

Locating the turn signal flasher box

The flasher unit is built into the 4 way flasher switch I am not sure about yours let me know if it is thanks

Apr 04, 2009 | 2000 Chevrolet Camaro

2 Answers

Hi i have a 2002 chevy camaro and the turn signals will not blink

You need to replace the flasher. I'm not sure where it is located, but I can look it up if you need me too

Apr 01, 2009 | 2002 Chevrolet Camaro

2 Answers

97 camaro turn signals fail to work

sounds like two problems. the front turn signals operate through the drl module. It's behind the radio. if you cut and splice the dk. blue to dk. blue w/ white, lt. blue to lt. blue w/ white on the black connector it will bypass the drl but all other functions will work. some say to disconnect the blue connector to bypass however this will discontinue other features, e-brake indicator, rear hatch button, ect. As for the rear light, i would check the rear lamp harness connector behind the interior plastic drivers side for power on the right signal feed and the splice ground.

Mar 21, 2009 | 1997 Chevrolet Camaro

1 Answer

My turn signals stay on

You have daytime runing lights. When you turn the signal off does it just stay on or does it flash? If it just stays on and you have some light dimming problems, it is more than likely a bad ground on the front signal sockets. This can be repaired by cleaning or replacing the sockets. Another cause of this problem can be traced to bad bulbs,a very easy fix.Good luck Moe

Feb 15, 2009 | 2000 Chevrolet Camaro

Not finding what you are looking for?
2000 Chevrolet Camaro Logo

Related Topics:

250 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides