Question about 2007 Lancia Beta

1 Answer

Attaching a genuine Lancia rear Evo spoiler to a Lancia Integrale

Hi, I have got a 1991 Integrale Evo and want to attach the rear spoiler to the rear hatch back door. The car has never had a spoiler and I want to position it correctly. Are there some specifications, measurements etc. available to that I locate it in the correct place / position on the rear door / hatch?

Please note that I have had to list this question using the Lancia Beta 2007 product code as there did not seem to be my model available to select from.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lancia Master
  • 3,187 Answers

Place the spoiler in the aria you want to fit it and make measurements, so they equal either side mark with a wipeable pen. and then measure the boot edge to where the spoiler is so its straight. check twice the drill the holes out using the the plate of the spoiler for the markings, check twice then drill measure twice. should fit right and look right.

Posted on Jun 06, 2017

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 141 Answers

SOURCE: Where can i get a

go on line and find the nearest alfa romeo car club kdc744

Posted on Jan 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove car rear spoiler


usually held on by bolts within the boot lid that they are attached to

Mar 19, 2015 | Cars & Trucks

1 Answer

964, rear spoiler won't work


Start by checking remote switch. Test to see if there is power at the spoiler motor. If there is power getting to the motor check for bad ground. Finally remove the cable that drives the spoiler up and down and apply 12v dc to the motor. If the motor turns check to see if you can turn the cable without the motor and that the spoiler moves. I all power checks out and the spoiler won't move by turning the cable, the gearing that the cable attaches to is most likely damaged.

Jan 19, 2014 | 1991 Porsche 911

1 Answer

How do I replace the timing belt and water pump on my 1991 sun bird. 2.0 liter engine


Water Pump: Remove timing belt rear protective covers, Remove lower radiator hose from water pump. Remove water pump attaching bolts then the water pump and sealing ring, Clean engine block and water pump sealing surfaces, then apply a 3/32 inch of RTV sealant to sealing surfaces. While RTV sealant is still wet, install water pump. Tighten attaching bolts finger tight. Install lower radiator hose on water pump, then belt rear protective covers. Install timing belt

Jan 18, 2013 | Cars & Trucks

1 Answer

I need to know how to seperate my transmission from my block


REMOVAL & INSTALLATION C6
  1. Disconnect the negative battery cable.
  2. From in the engine compartment, remove the two upper converter housing-to-engine bolts.
  3. Disconnect the neutral switch wire at the in-line connector.
  4. Remove the bolt securing the fluid filler tube to the engine cylinder head.
  5. Raise and support the truck on jackstands.
  6. Place the drain pan under the transmission fluid pan. Starting at the rear of the pan and working toward the front, loosen the attaching bolts and allow the fluid to drain. Finally remove all of the pan attaching bolts except two at the front, to allow the fluid to further drain. With fluid drained, install two bolts on the rear side of the pan to temporarily hold it in place.
  7. Remove the converter drain plug access cover from the lower end of the converter housing.
  8. Remove the converter-to-flywheel attaching nuts. Place a wrench on the crankshaft pulley attaching bolt to turn the converter to gain access to the nuts.
  9. With the wrench on the crankshaft pulley attaching bolt, turn the converter to gain access to the converter drain plug. Place a drain pan under the converter to catch the fluid and remove the plug. After the fluid has been drained, reinstall the plug.
  10. On 2WD drive models, disconnect the driveshaft from the rear axle and slide shaft rearward from the transmission. Install a seal installation tool in the extension housing to prevent fluid leakage.
  11. Disconnect the speedometer cable from the extension housing.
  12. Disconnect the downshift and manual linkage rods from the levers at the transmission.
  13. Disconnect the oil cooler lines from the transmission.
  14. Remove the vacuum hose from the vacuum diaphragm unit. Remove the vacuum line retaining clip.
  15. Disconnect the cable from the terminal on the starter motor. Remove the three attaching bolts and remove the starter motor.
  16. On 4WD drive models remove the transfer case.
  17. Remove the two engine rear support and insulator assembly-to-attaching bolts.
  18. Remove the two engine rear support and insulator assembly-to-extension housing attaching bolts.
  19. Remove the six bolts securing the No. 2 crossmember to the frame side rails.
  20. Raise the transmission with a transmission jack and remove both crossmembers.
  21. Secure the transmission to the jack with the safety chain.
  22. Remove the remaining converter housing-to-engine attaching bolts.
  23. Move the transmission away from the engine. Lower the jack and remove the converter and transmission assembly from under the vehicle. To install:
  24. Tighten the converter drain plug.
  25. Position the converter on the transmission making sure the converter drive flats are fully engaged in the pump gear.
  26. With the converter properly installed, place the transmission on the jack. Secure the transmission on the jack with the chain.
  27. Rotate the converter until the studs and drain plug are in alignment with their holes in the flywheel.
  28. Move the converter and transmission assembly forward into position, using care not to damage the flywheel and the converter pilot. The converter must rest squarely against the flywheel. This indicates that the converter pilot is not binding in the engine crankshaft.
  29. Install the converter housing-to-engine attaching bolts and tighten them to 65 ft. lbs. (88 Nm) for the diesel; 50 ft. lbs. (68 Nm) for gasoline engines.
  30. Remove the transmission jack safety chain from around the transmission.
  31. Position the No. 2 crossmember to the frame side rails. Install and tighten the attaching bolts.
  32. Install transfer case on 4WD drive models.
  33. Position the engine rear support and insulator assembly above the crossmember. Install the rear support and insulator assembly-to-extension housing mounting bolts and tighten the bolts to 45 ft. lbs. (61 Nm).
  34. Lower the transmission and remove the jack.
  35. Secure the engine rear support and insulator assembly to the crossmember with the attaching bolts and tighten them to 80 ft. lbs. (108 Nm).
  36. The balance of installation is the reverse of removal.
AOD
  1. Disconnect the negative battery cable.
  2. Raise the vehicle on hoist or stands.
  3. Place the drain pan under the transmission fluid pan. Starting at the rear of the pan and working toward the front, loosen the attaching bolts and allow the fluid to drain. Finally remove all of the pan attaching bolts except two at the front, to allow the fluid to further drain. With fluid drained, install two bolts on the rear side of the pan to temporarily hold it in place.
  4. Remove the converter drain plug access cover from the lower end of the converter.
  5. Remove the converter-to-flywheel attaching nuts. Place a wrench on the crankshaft pulley attaching bolt to turn the converter to gain access to the nuts.
  6. Place a drain pan under the converter to catch the fluid. With the wrench on the crankshaft pulley attaching bolt, turn the converter to gain access to the converter drain plug and remove the plug. After the fluid has been drained, reinstall the plug.
  7. On 2WD drive models, matchmark and disconnect the driveshaft from the rear axle and slide shaft rearward from the transmission. Install a seal installation tool in the extension housing to prevent fluid leakage.
  8. Disconnect the cable from the terminal on the starter motor. Remove the three attaching bolts and remove the starter motor. Disconnect the neutral start switch wires at the plug connector.
  9. Remove the rear mount-to-crossmember attaching bolts and the two crossmember-to-frame attaching bolts.
  10. Remove the two engine rear support-to-extension housing attaching bolts.
  11. Disconnect the TV linkage rod from the transmission TV lever. Disconnect the manual rod from the transmission manual lever at the transmission.
  12. Remove the two bolts securing the bell crank bracket to the converter housing.
  13. On 4WD drive models, remove the transfer case.
  14. Raise the transmission with a transmission jack to provide clearance to remove the crossmember. Remove the rear mount from the crossmember and remove the crossmember from the side supports.
  15. Lower the transmission to gain access to the oil cooler lines.
  16. Disconnect each oil line from the fittings on the transmission.
  17. Disconnect the speedometer cable from the extension housing.
  18. Remove the bolt that secures the transmission fluid filler tube to the cylinder block. Lift the filler tube and the dipstick from the transmission.
  19. Secure the transmission to the jack with the chain.
  20. Remove the converter housing-to-cylinder block attaching bolts.
  21. Carefully move the transmission and converter assembly away from the engine and, at the same time, lower the jack to clear the underside of the vehicle.
  22. Remove the converter and mount the transmission in a holding fixture.
  23. Tighten the converter drain plug. To install:
  24. Position the converter on the transmission, making sure the converter drive flats are fully engaged in the pump gear by rotating the converter.
  25. With the converter properly installed, place the transmission on the jack. Secure the transmission to the jack with a chain.
  26. Rotate the converter until the studs and drain plug are in alignment with the holes in the flywheel.
  27. Move the converter and transmission assembly forward into position, using care not to damage the flywheel and the converter pilot. The converter must rest squarely against the flywheel. This indicates that the converter pilot is not binding in the engine crankshaft.
  28. Install and tighten the converter housing-to-engine attaching bolts to 40-50 ft. lbs. (54-68 Nm).
  29. The balance of installation is the reverse of removal.
prev.gif next.gif

Nov 03, 2010 | 1991 Ford F150

1 Answer

Headlight replacement on a 1991 pontiac grand am


Sealed Beam Type
  1. Disconnect the negative battery cable.
  2. Unfasten the headlight bezel attaching screws, then remove the bezel.
8ed2813.gif
Remove the headlight bezel

To avoid turning the vertical or horizontal aiming screws, refer to the illustration before removing the headlight retainer.
  1. Unfasten the headlight retainer attaching screws, then remove the retainer.
e11bb51.gif
Remove the headlight trim screws then...

67522f3.gif
... pull the trim off while holding the bulb

4. Pull the headlight out, then carefully detach the electrical connector.

8d80048.gif
Pull the bulb out far enough to disconnect the wiring


To install:
  1. Attach the electrical connector to the new headlamp.
  2. Place the headlamp into the socket.
  3. Install the retainer, then tighten the attaching screws.
  4. Connect the negative battery cable, then turn the headlight switch on, to be sure the headlights are operating.
  5. Install the headlight bezel and secure using the attaching screws.

Jan 18, 2010 | 1991 Pontiac Grand Am

1 Answer

How do you replace the brake light on the rear spoiler on a 2001 Hyundai Accent?


This is the Spoiler Dude. The spoiler light is attached with screws to the spoiler. You must remove the screws and then the spoiler light will come away from the spoiler. Clip the two wires ( Black & Red ). Attached the new spoiler light ( I can get that for you) with a sleeve. Test the new light with the brake pedal depressed. Screw in the new light and that is it. If you have any questions.
Call Spoiler Dude Paul
719-661-8600
www.spoilerdudepaul@gmail.com

Apr 20, 2009 | 2001 Hyundai Accent

1 Answer

Trying to remove the starter on a 1991 SaturnSL


no there is not a special tool need more info go to collisionrepairadvice.com for more
1991 Saturn SL L4-1.9L DOHC VIN 7 Vehicle Level a_003366.gif Starting and Charging a_003366.gif Starting System a_003366.gif Starter Motor arrow1.gif Service and Repair arrow2.gif blnk_spc.gif Service and Repair Notes
  1. Disconnect battery ground cable.
  2. Remove air inlet tube and fresh air hose, on DOHC models, lift resonator upward to disengage from engine support bracket.
  3. Remove upper starter attaching bolt through access hole near intake manifold support bracket.
  4. Raise and support vehicle.
  5. Using suitable pliers, remove starter shield pin, then lift shield upward to release from solenoid.
  6. Disconnect starter electrical connectors and position aside.
  7. Remove lower starter attaching bolt.
  8. Remove rear starter support bracket attaching bolt.
  9. Rotate starter until bracket clears axle shaft support bracket, pull rearward toward lefthand side of vehicle to remove.
  10. Reverse procedure to install. Torque starter attaching bolts to 26 ft. lbs., starter bracket bolts to 22 ft. lbs. and starter solenoid terminal to 3 ft. lbs.

Apr 11, 2009 | 1991 Saturn SL1

1 Answer

Spoiler


i have a rear spoiler for a 91 mazda protoge 4 door.

Aug 26, 2008 | 1991 Mazda 323

2 Answers

1991 Ford Ranger manual transmission remove


444a343.jpg
  1. Disconnect the negative battery cable.
  2. Remove the gearshift lever assembly from the control housing.
  3. Cover the opening in the control housing with a cloth to prevent dirt from falling into the unit.
  4. Raise the vehicle and support it safely.
  5. On 2WD vehicles, matchmark the driveshaft to the rear axle flange. Position a drain pan under the tailend of the transmission. Remove the driveshaft-to-rear axle flange fasteners and pull the driveshaft rearward to disconnect it from the transmission.
  6. Disconnect the clutch hydraulic line a the clutch housing. Plug the lines.
  7. Disconnect the speedometer from the transfer case/extension housing.
  8. Disconnect the starter motor, back-up lamp and, if equipped, neutral sensing switch harness connector.
  9. Place a wood block on a service jack and position the jack under the engine oil pan.
  10. On 4WD vehicles, remove the transfer case from the vehicle.
  11. Remove the starter motor.
  12. Position a transmission jack, under the transmission.
  13. Remove the transmission-to-engine retaining bolts and washers.
  14. Remove the nuts and bolts attaching the transmission mount and damper to the crossmember.
  15. Remove the nuts and bolts attaching the crossmember to the frame side rails and remove the crossmember.
  16. Lower the engine jack slightly to angle the transmission assembly. Work the clutch housing off the locating dowels and slide the clutch housing and the transmission rearward until the input shaft clears the clutch disc.
  17. Lower the transmission jack and remove the transmission from the vehicle.
To install:
  1. Check that the mating surfaces of the clutch housing, engine rear and dowel holes are free of burrs, dirt and paint.
  2. Place the transmission on the transmission jack. Position the transmission under the vehicle, then raise it into position. Align the input shaft splines with the clutch disc splines and work the transmission forward into the locating dowels.
  3. Install the transmission-to-engine retaining bolts and washers. Tighten the retaining bolts to specifications. Remove the transmission jack.
  4. Install the starter motor. Tighten the attaching nuts.
  5. Raise the engine and install the rear crossmember, insulator and damper and attaching nuts and bolts. Tighten and torque the bolts to specification.
  6. On 4WD vehicles, install the transfer case.
  7. On 2WD vehicles, insert the driveshaft into the transmission extension housing and install the center bearing attaching nuts, washers and lockwashers. Connect the driveshaft to the rear axle drive flange.
  8. Connect the starter motor, back-up lamp and, if equipped, neutral sensing switch connectors.
  9. Connect the hydraulic clutch line and bleed the system.
  10. Install the speedometer cable.
  11. Check and adjust the fluid level.
  12. Lower the vehicle.
  13. Install the gearshift lever assembly. Install the boot cover and bolts.
  14. Reconnect the negative battery cable.
  15. Check for proper shifting and operation of the transmission.
The above was pulled frrom:
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800391da

hope this helps

Jul 02, 2008 | 1991 Ford Ranger Supercab

1 Answer

Nissan Maxima 91 Rear Spoiler brake light broken


some of this cars have 1 fuse per side make sure to chek all the fuses some cars have more than one fuse box

May 29, 2008 | 1991 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

316 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lancia Experts

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

881 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Sam Akber
Sam Akber

Level 3 Expert

987 Answers

Are you a Lancia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...