Whenever I use the keyless entry or the power locks, it makes a click, but none of the doors lock or unlock. I checked the fuses and they are all fine. Could there be a relay that is maybe on the verge of dying?
An expert who has achieved level 2 by getting 100 points
An expert who has answered 20 questions.
An expert that has over 10 points.
An expert whose answer got voted for 2 times.
Re: 2002 Dodge Neon power locks are weak
I would start by lubricating the lock mechanism, this would be done best if the door panel was taken off. If this doesn't do the trick then you will need to replace the auto lock solenoid that is in the door.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
20 out of 32 products in Alarms, Remote Car Starters, Keyless Entry & Locks ..... ofKeyless Entry & Car Alarms allow you to lock and unlock power door locks.
How to program your keyless entry keypad - Ford Ownerhttps://owner.ford.com/.../locks.../how-to-program...Ford Motor CompanyDiscover how to lock and unlock your doors and how to program memory settings that will adjust seats & mirrors for each driver.SecuriCode™ Keyless Entry Keypad - Ford Ownerowner.ford.com/.../locks.../securicode-keyless-entr...Ford Motor CompanyLearn how to set a 5 digit SecuriCode on the Ford keyless entry keypad. ... Sign out. Register/Sign In · Your Vehicle. Service & Maintenance. Service & .... vehicle's SecuriCode keypad to lock and unlock your doors without having to use a key. ... Thekeypad will go into an anti-scan mode if you enter the wrong code seven ...How Programming Your Keyless Entry Can Make ... - Ford Life
Programming Electronic Door Lock Control System
NOTE: The electronic door lock control processor (14B001) erases all
previous keyless entry remote transmitter (15K601) from memory when the keyless
entry remote transmitters are programmed or reprogrammed. The electronic door
lock control processor can store up to four keyless entry remote transmitters in
To program (or reprogram) keyless entry remote transmitter into the
electronic door lock control processor, perform the following steps:
Turn ignition switch to the RUN position and momentarily short the two
terminals of the program connector taped to the wire assembly and located behind
the glove compartment. All doors should lock and then unlock. Remove shorting
Press any button on keyless entry remote transmitter. All doors should lock
and then unlock to verify the keyless entry remote transmitter has been
programmed. If door locks do not respond, press button again (up to three times
maximum with the same keyless entry remote transmitter).
Repeat the above step to program additional keyless entry remote transmitters
into the electronic door lock control processor (up to four keyless entry remote
Turn ignition switch OFF. All doors should lock and then unlock.
IF DOOR LOCKS LOCK AND UNLOCK.WHILE HAND OPERATING DOOR LOCK SWITCH.YOUR REMOTE KEYLESS BATTERY WEAK.IF DOOR LOCKS DONT WORK BY USING YOUR HANDS TO WORK THE SWITCH.LOOK FOR A BLOWN FUSE OR CIRCUIT BREAKER.
I would check the obviouse first, That would be the battery in the remote. You can replace them from a radio shack store. Next find out the make of the keyless remote and email the manufacturer or call them. In fact thats how i solved my remote problem. There are also discount outfits on the net that will sell you another remote. You must give them the make and model and vin.
The keyless entry is designed to work with the doors closed (closed - not locked). If the door ajar sensor thinks the door is open the keyless entry is disabled. When you manually lock the door it might tighten the door just enough to activate the keyless entry. I would try slamming all the doors closed and then see if the keyless entry works. If it still wont work have the wiring checked on the front door lock.