Question about 2000 Chevrolet Tracker

1 Answer

Where does it go after the alt belt ratering is missine under hood

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 120 Answers

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sounds like birds chirping under hood..belt n


Bad over run pulley for the alt? Bad idler or tensioner bearings? could be a bad accessory like compressor, water pump, timing belt pulleys. . Best to list yr, make and model if you are requesting help if you want any real info

Sep 12, 2014 | Cars & Trucks

1 Answer

Whinning noise when acceration. Engine accelarates fine but there is also a whinning noise


check alt bearing,open hood & listen while running,turn off engine and remove drive belt then start engine to see if noise goes away.

Jul 10, 2014 | 2008 Jeep Compass

1 Answer

I need a belt diagram for a serpentine belt on a 1996 sentra


there should be a diagram of the belt routing on the car under the hood top of radiator. If not get a manual it will show you how the belt routes and how to remove and install the alt. otherwise ask your parts store to look up the job and print the directions for you

May 28, 2012 | Cars & Trucks

1 Answer

Missin hose's from brake booster under the hood i need a picture of where they run to


It would help lots to know on what. But a general answer for your general question, the booster vacuum hose will go to the intake manifold vacuum source.

Sep 04, 2011 | Dodge Dakota Cars & Trucks

1 Answer

Chevy Silverado z-71 engine belt diagram 2000


Most trucks have a belt diagram right under the hood. If yours is missins. contact a gm dealer for a replacement sticker. Probably a couple bucks.

May 06, 2011 | 2000 Chevrolet Silverado

1 Answer

Our 2001 camry lost power going down the road and died. We looked under the hood and the pulley that comes off the engine that runs the alternator belthad came apart. If the pulley came apart and that belt...


I'm not sure about the belt set up, it should be on a sticker under the hood. But losing your alt can cause the car to die due to loss of electrical power to run the computer, fuel pump, coils, ext. on some cars you can run for awhile on the battery, but eventually it'll die. Some cars are set up to die if the alt fails so that the rest of the cars systems can still be used

Apr 11, 2010 | 2001 Toyota Camry

1 Answer

I need diagram for alt. belt for 93-94 eclipse


Look under the hood. A lot of autos have a belt diagram printed on paper glued to the underside of the hood or the radiator shroud. If yours doesn't, go to any auto parts store and pick up a Hanes or Chilton shop manual for your car. Tons of good info.

Oct 30, 2009 | 1993 Mitsubishi Eclipse

1 Answer

1993 beretta serpentine belt diagram


well its hard to describe but here goes. the belt will run across the top from the PS pump to the alt. from the alt to the inside of the water pump, then to the outside of the a/c comp . then around the crank pulley, then up to the inside of the tensioner, then up around the outside of the PS pump. It will be easier to put the belt around all the pulleys except the alternator, release the tensioner and with the belt loose, slide it over the alt pulley. GOOD LUCK. I hope you fixed the problem with the belt, they just dont fall off for no reason. ck tensioner pulley, water pump.

Sep 18, 2009 | 1993 Chevrolet Beretta

1 Answer

Alternator need to be replace


under the hood find the alternator, then on the alternator there a bolt on the side that is long you have to loosen it last after u loosen the bolts that are holding the alt then the long bold last it loosens the belts ,take the belts of then but new one one and but the bolts that hold the alt on first dont tighten them then the big bolt make it tight how u need not to tight and then tighten the bolts that hold the alt tigher,if my info was of any help to you please leave a comment,thank you.

Sep 03, 2009 | 1998 Lincoln Town Car

Not finding what you are looking for?
2000 Chevrolet Tracker Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6864 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...