Question about 1995 Nissan Pickup

2 Answers

Rear Window was broken have a new one, but how do I replace it?

It is a 1995 Nissan Pickup the rear window has a slide with a latch, I want to replace the whole thing with a matching (unbroken) one. How do I go about getting that done?

Posted by on

  • Anonymous Apr 09, 2009

    Rear Window was broken have a new one, but how do I replace it?" problem, and notify you when a new solution is offered.

  • yadayada
    yadayada May 11, 2010

    have a glass shop do it

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

On the interior, there is a rubber lip surrounding the window. This rubber lip holds the glass in place. Here is how to remove without breaking stuff: Collect about 6 sticks (more is better) that are flat and preferabley made of something a little bendable. The ones I use are plastic and measure 8 inches by 1/4 inch by 1 inch and taper down to a blunt, rounded blade at the end.
From the interior, pull back the rubber lip where it meets the cab... not the glass. Where the lip meets the cab, you jam one of the sticks in place so it holds the rubber lip away from the cab of the truck (towards the glass). Start near a corner. About 4 inches away, do this again. Keep doing this until you have all the sticks in place. I found that doing this around one end of the glass (driver or passenger side) allows me to work that end out and the rest will come out with minimal hassle.
To install:
Place window on stand and wrap rubber gasket around window.
Run a string that is about an 1/8 or 3/16 diameter into the groove that grabs the pinchweld of the cab. The string should be long enough to overlap. Overlap by at least a couple of inches. Tape excess string to interior of window.
Have help to jam the bottom of window INTO the cab opening and try to center as best you can.
While applying LIGHT pressure to outside of window, pull one end of string. What you are watching for is that the rubber lip at least catches the cab pinchweld. If you miss this, you will have to start over. (Sometimes you can save it if you have a hook tool handy. A hook tool is essentially a screwdriver bent sharply at a 90 degree angle.)
If you do it right, as you pull the string, it will pull the rubber lip toward the interior of the truck and it will catch the pinchweld of the window opening. A little messaging and slapping of the window will fully seat the glass.
You are done.

Posted on May 10, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 120 Answers

Very easy to do take out from inside the seal u need two people to do it

Posted on Feb 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 s10 blazer rear window latch broken


it is easier and best to replace the hole window with latches. The latches do not come off. A junk yard would have the back window. I have one in my shop with the same problem

Nov 25, 2012 | 1996 Chevrolet Blazer

1 Answer

Broken rear window latch


If self-installing and budget is a concern, I would suggest calling your local junkyard to see if you can purchase a replacement from them. If no luck, try pricing online vs your local auto retailer as parts are usually cheaper online.

Jun 29, 2012 | Dodge Cars & Trucks

1 Answer

Rear passenger window will not go up. the motor works but window does not move.


remove your door panel and make sure your window is still on the track and that none of the plastic holders are broken

Jan 20, 2011 | 1995 Nissan Maxima

3 Answers

Toyota hilux surf 1995 rear electric window broken


make sure rear wiper is all the way off or at rest position

Mar 26, 2009 | 1995 Toyota 4Runner

1 Answer

Broken door handle - 2001 Nissan Quest SE


first you van order parts at discount from tascafordparts.com.
quest & mecrury villager are the same vehicle made at the same assembly plant. good luck to all. If you were in detroit area, I wold help you.

Trim Panel —Sliding Door Removal
  1. Remove the sliding door trim panel finish panel.
532ac84.gif 2. Remove the sliding door trim panel 2965fbe.gif Latch Remote Control —Sliding Door Removal
  1. Remove the rear sliding door trim panel. For additional information, refer to Section 501-05 .
  1. Position the watershield aside.
  1. If equipped, disconnect the sliding door power door lock actuator electrical connector.
f373e91.gif
  1. NOTE: Mark the position of the sliding door rear latch cable adjusting bracket before removing the bolt.
  2. Disconnect the sliding door rear latch cable.
  3. Remove the bolt.
  4. Remove the sliding door rear latch cable adjusting bracket from the latch remote control.
  5. Disconnect the sliding door rear latch cable from the latch remote control.
b8f2f32.gif
  1. Remove the 4 sliding door front latch bolts.
NOTE: If necessary, transfer parts to the new sliding door latch remote control.
Remove the sliding door latch remote control.
  1. Remove the bolts.
  1. Remove the sliding door latch remote control.
cb5ee71.gif
Handle —Exterior, Sliding Door Removal
  1. Remove the sliding door latch remote control. For additional information, refer to Latch Remote Control—Sliding Door .
  1. Remove the sliding door exterior handle.
    1. Remove the nuts.
    1. Remove the sliding door exterior handle.
0c820f3.gif

Mar 08, 2009 | 2001 Nissan Quest

1 Answer

Can't open tailgate and rear window


if you take off interior panel.....push out the dent with a bar....then try button if no work go back inside and you should see bars going down from handle to latch area...pull up on it and should pop the trunk

Dec 02, 2008 | 1995 Isuzu Rodeo

1 Answer

Car windows rear


this car has a cable regulated window,check to see if guide for cable is not worn or broken.These regulators tend to be very expensive.Look at junk yard .

Oct 02, 2008 | 1990 Nissan Maxima

1 Answer

Rear driver side window


HAVE YOU REPLACED LATCH? IF SO YOU NEED TO ADJUST

Aug 27, 2008 | 2003 Kia Sedona

Not finding what you are looking for?
1995 Nissan Pickup Logo

1,421 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...