Question about 1998 Chevrolet S-10 Pickup

1 Answer

I have a 1998 Chevy S-10 and I am havin problems with the dash

Removing the dash to replace the heater core and am having problems loosening the left side and pulling the radio.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 94 Answers

If it wont pull out then something is definetly holding it in. Take your time and double check everything

Posted on Feb 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How do you replace a heater core on a 95 impala ss


How to Replace the Heater Corein a Chevy Impala

Replacing your Chevy Impala'sheater core is no easy task. There are several parts you must carefully removeor reposition to disconnect the core from the heating, ventilating and airconditioning (HVAC) module. This module and the core are located behind thecar's floor ducts.

1. Jack up the car and drain the Impala's cooling system.Loosen the water pump's drain bolt and let the coolant drain into a pan. Closethe drain bolt and lower the car afterward. 2. Remove the heater outlet and inlet hose from theheater core (reposition the hose clamps to do so). Take off the right consoleextension panel, body control module and left side extension panel on the frontfloor console 3. Disconnect the leftinstrument center support bracket (pull away the carpet at its bottom to reachthe nuts). Remove the accelerator control pedal from its position in the frontof the dash. 4. Disengage the center floorducts by raising the outlet duct while pushing the ducts down. Rotate theoutlet duct forward in the car and pull down to remove it from the HVAC module. 5. Use a small chisel to removeall the heat stakes from the heater core cover. Loosen the nut behind the fuelline bracket. Remove the dash panel's stud at the heater hoses. 6. Pull the core's cover downenough to reach the HVAC module's locating pins. Slide the cover rearward untilthe drain tube clears the dash front. Remove the cover by sliding it down,rearward, and to the right. You can now remove the core.
Installing the New Core
1. Install the new core into the HVAC module,attaching a new seal onto the drain tube. Attach the core cover from the rightside, sliding it up and forward into position. 2. Align the draintube with the front dash hole and the core cover holes with the HVAC locatingpins. Install the core cover screws, cutting and folding back the soundinsulator near the center screw to ease that screw's installation. 3. Reinstall the dash panel stud at theheater hoses, tightening the nut behind the fuel line bracket. Align the centerfloor duct with the HVAC and push it up while rotating rearward to install it.Put the floor ducts and outlet duct back into the Chevy Impala. 4. Attach theaccelerator control pedal. Pull the carpet back and position the left centersupport bracket, then tighten the bracket nuts. 5. Reconnect theleft side front floor console extension panel and the body control module tothe car. 6. Put on the outlethose and inlet hoses to the core, securing them with their clamps. Refill thecooling system with the proper mixture of water and coolant.
Read more: How to Replace the Heater Core in a Chevy Impala ' eHow.com

Nov 10, 2010 | 1996 Chevrolet Impala SS

1 Answer

I need to replace the heater core & blower motor on a 1996 Chevy S-10. I need info on removing the dash.


i could send you directions with images to replace heater core need email address and 8th digit of vin, W or X

Feb 07, 2010 | 1996 Chevrolet S-10 Pickup

1 Answer

How do i remove the heater core from my 1998 chevy 4x4 pu


start by removing glove box . then locate core and just start removing what you need to so you can get to it This is NOT a easy quick fix so take your time and remember how it came apart and where all the parts go

Dec 14, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

Heater core


HI. This is not an easy job but, im sure you will be able to accomplish this with a little guidance. I have put together a guide for you to follow. Its a step by step guide and, it will help you with this replacement of your heater core.


REMOVING THE OLD CORE--

#
Step 1

Jack up the car and drain the Impala's cooling system. Loosen the water pump's drain bolt and let the coolant drain into a pan. Close the drain bolt and lower the car afterward.
#
Step 2

Remove the heater outlet and inlet hose from the heater core (reposition the hose clamps to do so). Take off the right console extension panel, body control module and left side extension panel on the front floor console
#
Step 3

Disconnect the left instrument center support bracket (pull away the carpet at its bottom to reach the nuts). Remove the accelerator control pedal from its position in the front of the dash.
#
Step 4

Disengage the center floor ducts by raising the outlet duct while pushing the ducts down. Rotate the outlet duct forward in the car and pull down to remove it from the HVAC module.
#
Step 5

Use a small chisel to remove all the heat stakes from the heater core cover. Loosen the nut behind the fuel line bracket. Remove the dash panel's stud at the heater hoses.
#
Step 6

Pull the core's cover down enough to reach the HVAC module's locating pins. Slide the cover rearward until the drain tube clears the dash front. Remove the cover by sliding it down, rearward, and to the right. You can now remove the core.
Installing the New Core


INSTALLING THE NEW CORE---

#
Step 1

Install the new core into the HVAC module, attaching a new seal onto the drain tube. Attach the core cover from the right side, sliding it up and forward into position.
#
Step 2

Align the drain tube with the front dash hole and the core cover holes with the HVAC locating pins. Install the core cover screws, cutting and folding back the sound insulator near the center screw to ease that screw's installation.
#
Step 3

Reinstall the dash panel stud at the heater hoses, tightening the nut behind the fuel line bracket. Align the center floor duct with the HVAC and push it up while rotating rearward to install it. Put the floor ducts and outlet duct back into the Chevy Impala.
#
Step 4

Attach the accelerator control pedal. Pull the carpet back and position the left center support bracket, then tighten the bracket nuts.
#
Step 5

Reconnect the left side front floor console extension panel and the body control module to the car.
#
Step 6

Put on the outlet hose and inlet hoses to the core, securing them with their clamps. Refill the cooling system with the proper mixture of water and coolant.


Inspect the foam seal for the core on the lower HVAC case. Replace it with adhesive black foam tape if damaged.

Please rate and have a good day:)

May 06, 2009 | 2006 Chevrolet Impala

3 Answers

Replacment of heater core on 01 chevy S-10


Have replaced my heater core in my 2001 regular cab 4wd in december 2009. Had to pull the complete dash including the complete metal dash behind the dash that you see. Also had to remove the right passenger side inner fender well to acess the remaining two bolts that hold the heater core cover to the firewall. Its an insane job to do but the repair shop books call for 9 1/2 hrs to do the job. I'm not an expert but this is what it takes.

Mar 01, 2009 | 2001 Chevrolet S-10

1 Answer

1988 Chevy Blazer Heater Core Replacement


first determine if the heater core is located high or low by raising the hood checking against the firewall {by following the heater hoses to the fire wall} if it is high need to remove the dash. if it is low get on your back and start removing clips and screws no special tool needed.

Feb 14, 2009 | 1998 Chevrolet Blazer

2 Answers

1998 chevrolet k-1500 heater-core replacement


Remove the heater hose clamps and the hoses from the engine side of the firewall. From the inside under the dash on the pass. side, remove the lower panel screws and slowly pry the lower cover down and the heater core will slide out of the heater box. Installation is reverse of removal.

Sep 20, 2008 | 1995 Chevrolet S-10 CA Edition

1 Answer

Heater core


Ok to replace the heater core in the allante you must first take the door off the glove box by removing 4 screws in the corners by the hinges. Remove the valence below the dash on the passenger side.

Now follow these steps

1. remove the radio module disconnect all wires and set it aside
2. Remove the bracket that holds the engine control module slide it out and away
3. Remove the duct control unit slide it down and out from under the dash
4 remove the screws that hold the duct work together, rotate to right and then down from under the dash
5. After the prior the heater core is in view. it has two 8 mm screws holding it in place remove them
6. Now go under the hood with a long extension loosen the clamps on the heater core
7. with at least a 12 inch thin bent flat screwdriver at a 90 degree angle loosen the hose and wiggle it off the heater core nipples
8. Go back into the cockpit and remove the heater core by sliding rearward and to the right
9. Angle hater core down and slide out.
10. reverse to reassemble.

Aug 11, 2008 | 1993 Cadillac Allante

Not finding what you are looking for?
1998 Chevrolet S-10 Pickup Logo

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...