Question about 1995 Ford Econoline

1 Answer

Wipers and washers come on when ignition switch is turned on

Even when I unplug the turn signal and wiper harness, they still run all the time with ignition on. Ignition off they stop

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Probably the wiper motor. Typically the wiper control supplies a ground and the motors sometimes fail by shorting internaly to ground. The only fix is motor replacement or tear down and repair.

Posted on Mar 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

In my 2007 Saturn Vue there is what I think is an air pump which is cracked that one port is not connected to anything.


There is a electric motor that pumps washer fluid . Located in the bottom of the washer fluid tank .
Wash Operation (Front and Rear Wipers)
The front and rear washer systems use the same windshield washer fluid pump. When either the front or rear wiper is in the washer position voltage will be supplied to one side of the windshield washer fluid pump (depending on whether it is front or rear), while the other side of the pump is grounded.
At this point, the windshield washer fluid pump sprays solvent onto the windshield. When the front or rear washer is activated, the BCM receives an input from the switch that is activated. The BCM will control the wipers while in the WASH mode. The BCM will control either the front wiper relay or the rear wiper relay to turn on the wipers. The windshield wipers operate at low speed for 3 swipes and returns to the park position.

When turning on the washers do you hear the motor run ? Have some one try it while you listen at the washer fluid tank ! These pump motors do go bad .
turn OFF the ignition.
Disconnect the harness electrical connector of the windshield washer fluid pump.
Connect a test lamp from the windshield washer pump control circuit to a good ground .
Turn ON the ignition, with the engine OFF.
Press the front washer switch.
Does the test lamp illuminate?
YES or NO !

Nov 18, 2016 | Saturn Cars & Trucks

1 Answer

Foxguard jp2 immblsr on triumph stag will not de activate or go into service mode.Ignition switch operates as normal but dash lights stay off wipers and washers dont work .


Your half way there. All you need is a wiring diagram to trace the wire from the ignition to that fuse. Most likely it is one wire from the ignition, then it splices to the different fuses. In my experience the splice fails(corrosion), Some times you loose one area, some times all. Depends on which side of the splice is corroded the most. Splices are hard to find. Even harness diagrams can be as much as 2 feet off. I usually find the color code of the wire and run a new wire. In your case, it would be from the ignition switch to the fuse panel.

May 08, 2016 | 1977 Triumph Stag

1 Answer

Why is my windshield wipers running in the off position, it's like they are running in the intermittent position, but it's in the off position.


When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Schematic Reference: Wiper/Washer Schematics


1

Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Symptoms - Wiper/Washer Systems

2

  1. Turn the ignition ON.
  2. Turn the windshield wiper/washer switch OFF.
Are the windshield wipers always on?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

Disconnect the windshield wiper/washer switch connector.
Are the windshield wipers always on?
Go to Step 4 if yes
Go to Step 7 if no

4

  1. Disconnect the windshield wiper motor connector.
  2. Test the windshield wiper switch signal 1 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 5

5

Test the windshield wiper switch signal 2 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 6

6

Test the windshield wiper motor high speed circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 9

7

Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 8

8

Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement - On Vehicle in Steering Wheel and Column.
Is the repair complete?
Go to Step 11
--

9

Inspect for poor connections at the windshield wiper motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10

10

Replace the windshield wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the repair complete?
Go to Step 11
--

11

Operate the system in order to verify the repair.
Did you correct the condition?
The Wiper / Washer System consists of the following components:
?€¢
Windshield wiper / washer switch


?€¢
Windshield wiper system module / motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
Instrument panel cluster (IPC)


?€¢
ACC 15-amp fuse


?€¢
WSW 30-amp fuse

Jan 04, 2016 | 2002 Pontiac Bonneville

1 Answer

2007 Pontiac g6 wipers stay in upright position


Hey Derek , here is how the wipers park position is suppose to work !
Windshield wiper motor park operation is controlled by the body control module (BCM) using an input from the park switch within the wiper motor assembly. The BCM monitors the windshield wiper motor park switch circuit to determine if the windshield wiper blades are at the bottom of the glass. The circuit will be pulled to ground by the wiper motor park switch while the windshield wiper motor is operating. When the wiper switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the BCM will continue to operate the motor until the wipers reach the park position. If the ignition is turned OFF while the wipers are in mid-cycle, the wipers will stop immediately where they are. The BCM will park the wipers the next time the ignition is turned ON.
The wipers will not park when they are commanded ON and OFF with a scan tool. The BCM will park the wipers the next time the wiper switch is turned ON and OFF.
The BCM provides stall protection for the wiper motor by monitoring the park switch. If the park switch does not transition for 3 seconds while the wipers are operating, the BCM will assume that the wiper motor is stalled, and will de-energize the wiper relay until the wiper switch is cycled OFF and ON again.
Check for a voltage signal on the yellow wire at the wiper motor assembly , this is signal to the BCM ! If there is no signal you need to replace the windshield wiper motor assembly ? If there is a signal need to have Tech 2 scan tool hooked up to see if The BCM is the problem ! Relay #39 an #40 are the high an low wiper relays in the under hood fuse block ! Do you have a volt meter ,do you know how to do electrical testing ?

Sep 21, 2015 | Pontiac Cars & Trucks

1 Answer

When the key is turned wipers come on, and the right turn signal blinks fast. We think it might be a short in the wires but can't find out where. Is there something else that could be causing the


Technically, the wipers and turn signals are on two different circuits. But its possible the wires have melted together. One place to look would be in the steering col where the wiper switch and turn signal switch come together.
You could try unplugging the harness to see if the wipers still run.

Jan 18, 2013 | 1999 Dodge Stratus

2 Answers

Windshield wipers won't shut off


Turn wipers to off then turn the car off. We have the same problem in our 1986 Pontiac parisienne brougham

Nov 23, 2012 | 1986 Pontiac Parisienne

1 Answer

Windsheild washer and wipers wont go off.


I assume you mean the harness for the switch, because if the wiring harness for the motor is unplugged it should not have a way to get power.
There is a wiper relay and a front electronic module, either one could be faulty and causing the motor to have power with the switch off.

Sep 22, 2012 | 1999 Ford Windstar

3 Answers

1996 Dodge Grand Caravan wipers continue to run after ignition is turned off. The only way to stop them is to disconnect the battery or unplug the wiper motor. The switch will turn on the wipers (after...


The multi- function switch (turn signal switch) Your wipers are control by this switch. This problem is very common on dodge and chrysler with this switch failing.

Sep 13, 2009 | 1996 Dodge Caravan

1 Answer

2000 Jetta 2.0 gasoline engine. Multiple electrical problems. headlights will not turn on, only hi beam and only while holding lever up. A/C blower motor, wipers, and turn signals shut off as soon as...


most likely you have a very bad ignition switch, the only other pathway for switched acc. to operate when key is off is if someone has had the wires feeding the fuse box crossed. so unless you had recent wiring done by an amature, you need and ignition switch. after replaceing you may still need to replace some fuses or bulbs that didn't like being powered at the wrong time.

Mar 31, 2009 | 2000 Volkswagen Jetta TDI

Not finding what you are looking for?
1995 Ford Econoline Logo

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...